Download SOLAR WATER GARDEN SYSTEM

SOLAR WATER GARDEN SYSTEM
instructions manual
Manufactured for
www.aquatecequipment.com
PO Box 648, Maddington, Western Australia, 6989
Telephone (08) 9452 2444
Email [email protected]
www.aquatecequipment.com
SOLAR WATER GARDEN SYSTEM
instructions manual
Congratulations on your purchase of this product by AquaPro,
the answers for your watergarden made easy!
AP800SP
VOLTAGE (V)
12-20
POWER (WATTS)
Variable
MAX HEIGHT (M)
1.5
FLOW MAX (L/H)
800
Cable Length (m)
5.0
DESCRIPTION AND FEATURES
INSTALLATION
Your Aquapro solar system has been
manufactured with advanced technology to
provide you with the best quality system
for your pond or water feature.
1.Unpack the contents of your kit
and locate all parts ready for assembly
(as above).
• Aquapro Solar Pumps are suitable
for use in many different applications
including; fountains, water features,
small ponds and hydroponics.
• Your Solar Pump has a single moving
part (an impellor set) therefore enabling
easy cleaning and maintenance.
• The pump motor electrical components
are encapsulated in epoxy resin,
ensuring safe operation under water.
• The Solar Pump has a robust bearing and
shaft design so no oil/ grease lubrication
is required.
• The flow can be controlled by turning the
voltage control, allowing the pump to
use less power and therefore run longer.
2.Attach the mounting bracket to the solar
panel frame and either screw to a solid
surface or attach the garden spike, and
position in a convenient location in full
sunlight, facing north.
3.The control/battery housing must be
placed in a covered location out of the
weather. Connect the cable from the
solar panel to the plug on the side of
the housing. Connect the plug from
the pump into the socket on the front
of the housing.
OPERATION
1.Once installed, allow the solar pump
to charge at least eight hours in direct
sunlight to fully charge the battery.
2. When the solar panel is in the sunlight
and the battery is charging, the
“charging indicator light” will blink every
2 seconds.
3.To turn the system on, press the ON
button in the control housing. The green
POWER ON LED indicator light will glow,
indicating the system is ready to use.
4.To choose a mode, press the mode
button and the indicator light will
alternate between the “SOLAR
POWERED (DAY MODE)”,THE
“BATTERY POWERED (NIGHT MODE)”
and the “CHARGING MODE”. In the
SOLAR POWERED (DAY MODE) the
pump operates in direct sunlight only
and any surplus power is used to charge
the battery. In BATTERY POWERED
(NIGHT MODE) the pump will run for 2
hours only off the battery power then
automatically shut off, it will then run
for 2 hours every 24 hours at the time
when you first activated the night mode.
If you want to run the pump for one
time only off the battery power press
the cycle button and the indicator light
will illuminate. In the CHARGING MODE
the pump does not operate – all energy
from the solar panel is used to charge
the battery. We recommend using the
charging mode when charging for 8
hours the first time you use your pump.
5. The flow rate of the pump can be
controlled by the variable voltage
adjuster dial on the control housing. The
greater the flow on your solar pump,
the more energy consumed, therefore
the operating time will be shorter in
BATTERY POWERED (NIGHT MODE).
6. Your AP800SP Solar Pump also has a
low battery alert. When the battery is too
low, the “LOW BATTERY” indicator light
will blink every 2 seconds. Allow the
system to recharge in full sunlight for at
least 4 hours before turning on.
4.Connect the fountain riser pieces
together, then connect the risers onto
the outlet of the pump and attach either
the bell or the daisy spray nozzle to the
top. If you do not require the fountain kit
go to step 5.
5.Connect tubing to the outlet or attach
fountain kit (step 4), then place the
pump in desired location.
6.Ensure pump is submerged, the pump is
now ready to use.
1
2
SOLAR WATER GARDEN SYSTEM
instructions manual
MAINTENANCE
1 Impellor Cover
Disconnect power cord from the battery
before performing maintenance. Never lift
the pump by the power cord.
2Impellor
3 Pump Base (Sliding)
The only serviceable item is the
impellor set.
4 Pump Motor Body
5Top Of Pump Cover
6 Bottom Of Pump Cover
The motor unit of the pump is
encapsulated with epoxy resin and does
not need lubrication.
7 Filter Sponge
8Fountain Nozzle x2
All Aquapro submersible pumps are water
cooled; if pump becomes restricted it
will overheat and could cause permanent
damage. Ensure pump does not become
blocked or restricted.
9 Battery Housing
10 8 Watt Solar Panel
The power cord cannot be replaced. If
the cord is damaged, the pump must be
discarded.
8
10
If the impellor set becomes worn or
damaged it should be replaced (available
from your dealer or special orders).
Failure to do so may cause serious
damage to pump.
5
9
3
1
The impellor set is a wearing consumable
part. Regular inspections, cleaning, and
maintenance of impellor is necessary to
ensure longer impellor life.
2
1.Disconnect the power cord from the
battery before performing maintenance.
2.The solar panel should be cleaned
periodically with a soft tissue. Regular
cleaning of the panel is recommended to
maintain optimum efficiency.
3.Remove from water, detach tubing/
fountain kit and take apart cage from
pump by pushing the 4 clips on the
sides and lifting the top half.
4.Remove the pump from the cage and
slide off the base of the pump in the
direction of the arrows.
5.Remove the impellor cover by turning
anti-clockwise and pulling out.
6. Gently remove the impellor and shaft,
use long nose pliers if needed. Take care
not to break ceramic shaft, because they
are very brittle.
7.Clean impellor, checking for any signs of
wear or damage.
8.Reinstall the impellor into the motor. The
impellor will pull itself in by magnetic
force, this is normal. (Take care not to
pinch your fingers).
9.Replace the impellor cover making sure
the shaft is located properly on the
impellor cover.
10.Replace the base, place pump back into
the cage, and clip together.
11.Re-attach tubing/fountain kit, submerse
in water, connect to battery, and turn on.
7
4
6
3
4
www.aquatecequipment.com
1Housing
2 Lead-Acid Battery
3Circuit Board
4Control Housing Panel
5 Screw
• Always unplug the pump from the
battery when not in use or before
performing any maintenance on the
pump. Never pull the cord to disconnect
the plug from the battery.
• The impellor set is a consumable
item and is therefore not covered
under warranty.
• Do not install or store the pump where
it will be exposed to extreme hot or cold
temperatures.
• Warranty will be void if any tampering,
removal of warranty labels, or electrical
circuitry is evident.
• Keep out of reach of children or pets.
This appliance should not be used
by children or infirm persons without
supervision.
• Do not cut the cord as this will result in
voiding your warranty.
• Care should be taken to arrange
the power cord so that it cannot be
accidently tripped over or pulled.
1
2
3
4
5
• Do not attempt to repair the pump
yourself. Return to an authorized
service centre or place of purchase if
a fault occurs. (Regular maintenance is
not considered repair and is required
by user).
• Do not use in water above 35°C.
REPLACING BATTERIES
IMPORTANT SAFEGUARDS
If the pump stops working after a long
period of time, the battery maybe beyond
its lifespan. The battery can be replaced.
Use only Aquapro replacement batteries.
To guard against injury, basic safety
precautions should be observed including,
but not limited to the following;
1.Open the control housing by undoing the
screws on the front and carefully remove
the front panel and circuit board. Take
care not to damage any connections.
2.Carefully slide out the battery,
disconnect the terminals, and dispose of
used battery as per local regulations.
3.Reconnect new battery and replace into
the control housing, replace front panel
and screws
5
• The pump should only be used in clean
water. Do not use the pump in any
solvent or liquid that is flammable.
• Do not operate the pump without
water at any time, permanent damage
may occur.
• Do not operate the pump if the
pump or any of the components of the
pump, such as the power cable, have
been damaged.
• Do not break or impact the solar panel,
the monocrystaline solar panel is
fragile and care should be taken not to
damage it.
• The control housing must be covered.
This item is not waterproof.
LIMITED WARRANTY
• Warranty covers only appliance defects
and faulty material and workmanship
within a 2 year period.
• Faults arising due to; accidents, misuse,
not following manufacturer’s guidelines/
instructions will not be covered.
• Batteries are replaceable parts and are
not covered by warranty.
• Warranty will be void if the power cord is
cut or damaged in any way.
• Warranty will be void if any visible signs
of overheating are present.
• Loss of livestock, damage to property,
or personal injury caused by this product
will not be covered.
• Warranty claims caused by installation
faults will not be covered.
• It is the customer’s responsibility to
return the faulty appliance for any
warranty claim, to Aquatec.
• For any warranty to be valid, an original
proof of purchase must be provided.
• Warranty will be void if the solar panel is
damaged in any way.
• Use of any power source, replacement
battery or parts, other than that sold by
Aquapro, will void the warranty.
• Our goods come with guarantees that
cannot be excluded under the Australian
Consumer Law. You are entitled to a
replacement or refund for a major failure
and for compensation for any other
reasonably foreseeable loss or damage.
You are also entitled to have the goods
repaired or replaced if the goods fail to
be of acceptable quality and the failure
does not amount to a major failure.
Note: Please consult your retailer for quality original Aquapro replacement parts for your Aquapro
product. Visit www.aquatecequipment.com for nearest stockists.
6