Download OFFICE OF THE PRINCIPAL e-mail [email protected] ,Tel

OFFICE OF THE PRINCIPAL
R.K.R GOVERNMENT POLYTECHNIC, JANJGIR-CHAMPA Pendri (C.G.) 495668
e-mail [email protected] ,Tel No. 07817-222456
TENDER - DOCUMENT
FOR
PURCHASE OF EQUIPMENTS
(2016- 2017)
fufonk lwpuk dzekad@'[email protected]@2016@495 tkatxhj]fnukad 21-06-2016
1.
Total Value of work
Approx Rs 15 Lacs (Rs. Fifteen Lacs only)
2.
Tender document issued to
3.
Cost of Tender
4.
Money receipt & Date
----------------------------------
5.
Date of issue of tender
----------------------------------
M/s------------------------------------------------------------Rs 500-00 (Rs Five Hundred only)
Issued by
Principal,
Government Polytechnic
Janjgir-champa ,CG
OFFICE OF THE PRINCIPAL
R.K.R GOVERNMENT POLYTECHNIC, JANJGIR-CHAMPA Pendri , (C.G.) 495668
e-mail [email protected] ,Tel No. 07817-222456
No./Tech/GPJ/Tender/2016/495
/Janjgir, Dated 21-06-2016
Sealed Tenders are invited from the intended manufacturer/authorized
dealer/registered suppliers for supply of Goods/ Equipments/ Machine to R.K.R Government
Polytechnic Janjgir-champa (CG). Details are as follows . Suppliers are required to submit
separate tender for each part.
1.
2.
3.
4.
Date of Issue of Tender
Last Date and time for Receiving Sealed Tender
Date and time of opening the tender
Tender fee
5A EMD for Electrical Deptt.
EMD for Electronics Deptt.
5B
EMD for Chemical Deptt.
5C
EMD for Civil Deptt.
5D
EMD for Workshop ( Welding, Carpentry ,
Plumbing)
5E
From 27 June to 26 July 2016
27 July 2016 (3.00 PM)
27 July 2016 (4.00 PM)
Rs 500
Rs 9300
Rs 7950
Rs 12690
Rs 8880
Rs 6570
TERMS AND CONDITIONS
Terms and conditions for supply of Machines/ Equipments are as per following list:
1.
a.
b.
c.
d.
e.
f.
g.
h.
i.
j.
k.
2.
3.
4.
5.
For participation in tender process following signed and stamped documents must be
furnished in envelope A – super scribed as “Technical Bid envelope A”
Income Tax return of 2015-16/clearance certificate and PAN no.
Registration of firm/company
Sales tax clearing certificate
TIN certificate from commercial tax department.
ISO/BIS/ISI certificate for firm/product
Manufacturer/dealer /Agency certificate
Balance sheet /Turnover of firm/company of last three yrs duly signed by CA.
DD for Tender fee (if not submitted earlier ) and DD for EMD
Item specifications /Literature /Brochure / leaflet regarding supplier/firm business.
Acceptance of terms and condition ( signed and stamped copy of tender document)
Any other document which you consider as necessary
Envelope B should contain price bid along with taxes and discount if any and super
scribed as “ Financial Bid envelope B”
Both envelope A & B should be put in a third big envelope and Super scribed as “
Tender for supply and installation of machine/equipment” All envelope should be signed
and should be sealed on all joints
Sealed envelope for the tender should be super scribed as tender Notice No495dated
21.06.2016 should be addressed to Principal, Government Polytechnic, Janjgir Pendri
(CG) Tender for ……………Deptt be clearly mentioned on the envelope (at Left- hands
side Top Corner).
Firstly technical bid and documents envelope-A will be opened and if it is found ok than
only financial bid envelope –B will be opened .
6.
The tender is liable to be rejected if not submitted as per the prescribed conditions and in
the prescribed format in envelope A and B .as given in point 1 & 2 .No further
clarification will be entertained.
7.
The suppliers should quote their offer/ rate in clear terms without any ambiguity. Discount
if any must be clearly specified.
8.
If the same supplier is submitting tender for more than one part then duplicate documents
/certificates are not required. only one set of documents is sufficient.
9.
The tender will be opened on the date and time given above in the presence of
tenderer(s) or their representative who desire to be present.
10.
Tender received after due date and time will not be entertained.
11.
The tender should be submitted in duplicate. Tender form is non transferable.
12.
The tender document is also available on the website www.cgdteraipur.ac.in. tenderer
can downloads the document from the website, in that case he has to deposit DD of Rs
500-00 in favor of Principal, Government Polytechnic , Janjgir at the time of
submission of tender. Otherwise his tender will not be entertained.
13.
A soft copy of the tender should be submitted along with the tender document.
14.
Item no. and page no of the tender form should be strictly in chronological order.
Make/model, name of the manufacturer with complete address should be mentioned
against each item and equipment.
15.
The tender should be sent in firms own letter pad along with terms and conditions .
Printed condition on the back of the tender will not be binding unless separately
mentioned.
16.
The tenderer must furnish complete and detailed technical specification supported by
printed literature/catalogue/leaflet of the equipment offered. Item no.and page no. of
the equipment should be mentioned in it. Incomplete specifications/ absence of
printed literature support may result in to the rejection of the tender.
17.
The rate should be FOR destination(Govt. Polytechnic Jangir Pendri ) on door delivery
basis including all taxes, packing forwarding, transportation etc. Warranty/ Guarantee if
any on any item it should also be stated clearly.
18.
Taxes, if leviable extra, should be clearly indicated, failing which the rate quoted in the
tender will be considered as inclusive of all taxes.
19.
There should be no alterations / corrections made in the Tender. The quoted rate should
be in figures and words both. The tenderer may quote the rate of any or all the items
listed in the tender form. Rates should be quoted separately for individual item and not in
lump-sum for all taken together
20.
The tender should clearly indicate whether the equipment is complete in itself. If in the
opinion of the tenderer, certain accessories are necessary with the type of the
equipment tendered, the tenderer must quote for aforesaid accessories under the
heading “extra but essential”.
21.
The tenderer are required to deposit EMD separately for each head The EMD should be
deposited in the form of Demand Draft/ Bankers Cheque drawn in favor of Principal,
Government Polytechnic, Janjgir (CG) payable at Janjgir against tender 495-Janjgir,
dated 21.06.2016. Tenders received without EMD will be rejected. Requests for relaxing
EMD will not be entertained. EMD by cheque or MO will not be accepted.
22.
In case of non- acceptance of the tender the EMD will be refunded to the tenderer in due
course of time without interest. The EMD will be treated as security deposit in case of
selected tenders EMD/ security deposit will be forfeited in case of breech of agreement
of supply by the tenderer/ supplier. The order shall stand cancelled and security deposit
forfeited if:
(I)
Supplier expresses his inability to execute the order for the quoted items
within validity period of the tender at the rate quoted in the tender and for
makes/ brand quoted in the tender.
(II)
The complete equipment is not supplied within the delivery period
mentioned in the order or within the extended period permitted.
(III)
The supplier executes only a part of the order.
23.
Any Equipment/ Trainers/ Hardware or software breakdown must be attended within 48
hours during the valid warranty period of the equipment/ software, free of cost.
24.
Payment shall be released after the successful installation and demonstration of the
machine equipment at the institution.
25.
The training for at least two persons for handling the machine/ equipments shall provided
by the supplier at his own cost.
26.
The tenderer must have to give demonstration of the machine/ equipments software at
Government Polytechnic- Janjgir wherever necessary at his own cost.
The one time extension in the delivery period may be granted at the discretion of the
undersigned. The penalty at a rate of 2% per month of the full cost of the equipment is
liable to be charged for the extension of the delivery period
Equipment received after the delivery period or dispatched after the delivery period
mentioned in the order will also be subjected to this penalty.
In case of any default in execution of the order, the undersigned reserves the right
to forfeit the EMD/ Security deposit. The undersigned also reserves the right to cancel
the order and forfeit the EMD/ Security deposit in case the tenderer fails to adheres
strictly to all terms and condition of the order/ tender.
If defects of any kind or deviations from the specification are detected and reported to
the supplier, the supplier should make replacement or rectify the defects free of cost
within 30 days from the date of report, failing which the equipment will not be accepted
and will be taken back by the supplier at his own cost and risk, and the EMD will be
forfeited, In case the equipment is sent for repairs to the firm, it should be repaired within
30 days. from the date of receipt of equipment failing which the same will not be
accepted and EMD will be forfeited, However the undersigned may condone the delay in
deserving cases at his/her discretion.
27.
28.
29.
30.
31.
The undersigned reserves the right to increase/ decrease the quantity of the equipment to
be supplied. If equipment supplied are not according to the ordered specifications and
are not of proper quality ,the same will not be accepted .Similarly second hand,
reconditioned, damaged, repaired and substandard equipments and equipment having
poor workmanship would not be accepted . Only brand new equipment calibrated in
metric or SI unit and with fine workmanship will be accepted.
32.
The submission of the tender will be deemed to be the acceptance of all the terms and
condition of the tender as stated herein and/ or elsewhere in the tender document.
33.
Tenders should be valid for at least twelve months from the date of opening of the tender.
The prices should be firm without variations of any kind.
34.
If required "D" form duly completed and signed by the competent authority for reduction in
CST at the time of final payment shall be issued.
The undersigned reserves the right to accept the lowest or any tender and also of
rejecting whole (all) or any part of tender without assigning any reasons for the same or
to split up the tender as he/she may deem fit.
35.
36.
Exact and earliest possible time of delivery should be indicated in the tender against
each item. The delivery period given in the order will be the date of receipt of the
equipment in the institute and not the date of dispatch of the equipment by the supplier.
37.
No advance payment will be made. The successful tenderer will have to execute the
agreement bond in the form as approved by Government of Chhattisgarh
38.
If you have supplied these items to any PSU/ Government/ reputed Private firm/deptt.
Then submit last three years PSU/ Government/ Private Supply record as far as
possible.
39.
The tenderer/ bidder shall provide TIN No along with latest income tax clearance sales
tax clearance certificate from the concerned authority and attach it with the tender.
Tender received without these certificates shall be rejected.
The minimum warrantee period for the equipment supplied by the supplier should
be mentioned clearly and should not be less than one year from the date of installation.
The tenderer will be required to undertake repair/ replacement of defective parts free of
cost at the institution during the guarantee period
40.
41.
All the disputes with regard to the contract of purchase of equipment etc. is subjected to
Janjgir Chhattisgarh Jurisdiction only.
42.
In the event of the order, supplier who are the manufacturer of the equipment will be
required to furnish a certificate to the effect that they are manufacturers of such and
such make whereas the authorized agent/dealer/distributer or stockist will have to
furnish certificate issued by the manufacturer certifying that tenderer is their authorized
agent/ dealer/distributer/ stockiest of that product/item. Without this certificate tender will
not be accepted.
The equipment/ machinery calibrated in metric system need only be quoted.
43.
44.
45.
The tenderer shall guarantee that after sales services will be provided as and when
required. Replacement or repair of part should be done and delivered free of cost at this
institution.
The supplier will render necessary assistances, if required, in the installation of the
equipment/ machinery in the institute/ site free of charge.
46.
47.
48.
49.
No. offer should be made for imported item for which import license has to be
arranged by the undersigned. The entire imported item will have to be delivered in the
institute and payment will be made in rupees.
The payments shall be released only after satisfactory and successful commissioning
and installation of the equipment/ machinery at the designated site/ institute and on
submission of bill by the firm.
The rate quoted should preferably be net, inclusive of all taxes and duties, packing
forwarding, freight, insurance and other incidental charges. In case these charges
quoted extra in addition to the quoted rates, the amount there of or advolerun rate must
be specified.
Period of Guarantee/ Warranty, where applicable should be specified in the tender.
50.
In the event of any dispute arising out of the tender or from the resultant contract, the
decision of the Principal, Government Polytechnic, Janjgir (CG) will be final.
51.
52.
The Tender document/ resultants contract will be interpreted under Indian laws.
If the successful tenderer, on receipt of the order fails to execute the order within
the stipulated period, in full or part it will be open to the Principal, Government
Polytechnic, Janjgir (CG) to recover liquidated damage from the firm at the rate of 2% of
the value of undelivered goods per month or part thereof, subject to a maximum of 5% of
the value of undelivered goods. Alternatively, it will also be open to the Principal,
government Polytechnic Janjgir (CG) to arrange procurement of the required goods from
any other source at the risk and expenses of the tenderer.
The undersigned is not responsible for any loss or damage to the equipments during
transit irrespective of the fact that they are insured or not insured or delivery is ex- go
down or factory station.
53.
54.
No claim shall be entertained in respect of interest on Earnest Money / Security deposit/
Tender Deposit.
55.
Inspection of the equipment will be carried out at the institution after receipt of the
equipments. Any request for the inspection of the same at the firm's factory/ go down /
showroom etc. will not be accepted.
56.
Illustrated operation manuals, pamphlets/catalogue/literature/ working instructions,
trainers, software and hardware, erection/ wiring details as the case may be of the
ordered equipments must be supplied in suitable damp proof cover. Without
operational/instruction manual no equipment/machinery will be accepted.
In case of any variation of specification of any machine /equipment from tendered
specification it should be clearly mentioned . Specification nearest can also be
considered if it is as per technical norms for the given equipment/machinery.
57.
58.
59.
Only actual manufacturer or their authorized agent/dealer and stockiest may submit the
tender .It is mandatory to have ISO/BIS certification for supply/manufacture of the
item/equipments/machineries. Only BIS/ISO /ISI certified item has to be quoted.
The bidder shall submit a signed and stamped (on each page) copy of tender document
as testimony of acceptance of T&C of tender document.
Principal,
Government Polytechnic,Janjgir (C.G.)
GOVERNMENT POLYTECHNIC, JANJGIR (C.G.) 491001
Format for Technical Bid to be put in envelope A only
( This envelope will also contain documents as listed in point 1a to 1k)
S.no.
Name of Items along
with Make and model
1
2
Specifications
given in the
Tender
3
Technical
Specification
the bidder
wants to supply
as per
catalogue/
brochure
Remark
4
5
Signature:
(Name & stamp of the Firm/tenderer)
GOVERNMENT POLYTECHNIC, JANJGIR (C.G.) 491001
The Price offer should be submitted in the following format envelope B only
Sl
No
Name
of
Items
along
with
Make/
Model
1
2
Specifications Technical
Price
of
given in the Specification the
Tenders
which
the Equipment
bidder wants
to supply as
3
per
Catalogue/
Brochure
4
Taxes
(VAT/
CST
etc.)
Cost
of
the
Equipment
Inclusive
of all taxes
Remark
& charges
5
6
7
Signature:
(Name & stamp of the Firm/tenderer)
8
R.K.R. GOVT POLYTECHNIC JANJGIR
Tender no. 495 dated 21.06.2016
DEPARTMENT /WORK SHOP WISE LIST OF EQUIPMENTS & THEIR SPECIFICATIONS
Branch : Electrical Engg.
Lab. Title : Electrical Machine Lab
S.NO
Name of the Equipment
1
2
1
OC AND SC TEST SET UP OF SINGLE PHASE
TRANSFORMER WITH EFFICIENCY REGULATION
3
1KVA Transformer with Tapping at 33% ,66% and 100% Built in Variac Built in
voltmeter and Wattmeter ,built in MCB and Indicators all shrouded terminals.
DC Motor study kit
DC machine with loading arrangement type DC shunt rating : 1 HP , RPM : 1500 (NO
load) control panel made of powder coated metal body with complete safety features like
MCB etc. meters used voltmeter (MC) : 300V, Ammeter (MC) :1A,Ammeter (MC) :
5/10 A, Tachometer : 20,000 RPM Built in DC supply Speed control of DC shunt motor
by field current and armature voltage control, load characteristics of DC shunt motor,
study of self excited DC shunt Motor.
Analog Tachometer
Digital Non-Contact Tachometer
Digital Clamp meter
Type Range 10000 rpm with attachments
Range 10000 rpm Optical Contact Battery Operated type
33/4 digit LCD with 42 segment bar graph battery -1.5 V×2 AAA size DCV : 400/600V,
2
3
4
Specifications
5
±1.0%, ACV : 400/600V, ±1.5%, ACA : 40/ 400 amp ±2.0%, OH
6
Wattmeter 150-300/5-10A
Element Dynamometer Type for 3-phase 3 wire balance & Unbalance load Class 1.5%
7
Wattmeter 150-300-600/10-20A
Element Dynamometer Type for 3-phase 3 wire balance & Unbalance load Class 1.5%
Power Factor 1 Φ
Measuring Range : 0.5 (lead) - 1.0 (Unity) - 0.5 (lag) Range of P.F. Meter : Current
range : 5 A,110-440V
Rheostat
Rheostat
Variac 1 Φ,0-270 V /8A
Unbreakable metal tube type 150 Ω / 3A
Unbreakable metal tube type 110 Ω / 1.2A
Input Voltage 0-240 V AC, 50 HZ. Output 0-270 V AC Air cooled type in closed
enclosure
Variac 3 Φ,0-270 V /8A
Digital Insulation Resistance Testers
Input Voltage 415 V AC, 50 HZ. Output 470 V AC Air cooled type in closed enclosure
Battery Operated 2.5 KV 1000 Mega ohms with battery and LCD display
8
9
10
11
12
13
Branch : Electrical Engg.
1
Lab. Title : - EMMI & Circuit Lab
2
Earth Tester 3 terminal Type
3 terminal Type - 0-10/100 Ohms -hand Generator type with Earth Testing Kit 2 nos. MS
Spikes (45 cm Length) 3 nos. Rolls of flexible
Megger 1 KV
Hand Operated 500 Mega Ohms
1
2
Branch : Electrical Engg.
Lab. Title : - Instrument Lab
pH METER :
Range
: 0-14 pH
Resolution
: 0.01pH
Accuracy
: + 0.01 pH ( relative)
Temp. Comp.
: Automatic with temp. Probe
Buffer : Manuals with keys
Recognition : 4.00 , 7.00 , 9.20 ( Automatic)
Slope Adjustment : 80% to 120%, by default 100%
Calibration
: Auto/Manual 2-Point, 3-Point
OPTICAL PYROMETER
Centigrade and Fahrenheit Measurement Laser Target Pointer Selection Automatic
Data Hold Function Auto Power Off White Type K temperature measurements
Backlight LCD Display Over Range Indication Measurement Range : -20 Deg. To 500
Degrees C. Accuracy 2%.
3 ½ DIGITAL MULTIMETER – Auto ranging with
Protective Holster
Functions Range Accuracy DC Voltage 200mV/2V/20V/200V/1000V ±(0.5% + 4) AC
Voltage 200mV/2V/20V/200V/750V ±(0.8% + 5)
DC Current 200uA/2mA/20mA/200mA/2A/20A ±(1.0% + 5)
AC Current 200uA/2mA/20mA/20mA/2A/20A ±(1.5% + 5) Resistance 200 ±(0.8% + 1)
Temperature -40 ~ 1000 C / 0 ~ 1832 F ±(1.0% + 5)
1
2
3
3
Branch : Electrical Engg.
Lab. Title : -Power Electronics Lab
2
1
SPEED CONTROL OF INDUCTION MOTOR USING
TRIAC
On board firing circuits:- DIAC firing circuit Ramp & Pedestal firing circuit Firing angle
variation: Gradual variation from 0 to up to 180 degree using firing control Pot Pulse
transformer : PT4502, 1:1,Fuse : 1A, Mains Supply : 230 V ±10 %, 50 Hz . Power
Consumption: 2VA (approx.),Universal motor specifications: Single Phase-230V,1.2A, No
load RPM-17000 without load.
70 MHz Digital Storage Oscilloscope
• 70 MHz bandwidth Dual Channel, • 1 GS/s sample rate on all channels,• 2.5k point
record length on all channels,• 7 inch WVGA (800X480) Active TFT Color Display,• 34
automated measurements,• Dual window FFT, simultaneously monitors both the time
and frequency domains.,• Zoom Function,• Auto set and signal auto-ranging,• USB
Interface on front and rear panel.
1
2
Branch : Electrical Engg.
Lab. Title : - Basic Electronics lab
RC COUPLED AMPLIFIER TRAINER.
DC supply 12 V @ 500 mA On panel circuit diagram of RC coupled amplifier, Required
numbers of patch cords and operating manual.
MULTIVIBRATOR TRAINER USING TRANSISTOR
( ALL THREE ).
DC power supply +/- 12 V @ 500 mA On panel three circuits for A stable, Mono stable &
Bi stable multi vibrators , Required numbers of patch cords and operating manual.
1
2
3
BRANCH- ELECTRONICS ENGG.
Branch : Electronics Engg.
1
2
All device characteristics 14 (Discrete Component)
3
Built in rectifier from 230 (AC Supply) Built-in variable DC power supplies of +45 V,
+12 V (2 nos) @ 500 mA,
One 3 ½ digit LED dual range on panel meter to read voltage,
One 3 ½ digit LCD dual range on panel meter to read current,
Various range of resistors, capacitors and inductors mounted on panel,
Variable source for intensity control of lamp provided on panel,
DISCRETE COMPONENTS ON PANEL
Diodes: IN4007 & OA 79 Zener: 5 v 1 & 8 v 2 Transistors: SL 100 & SK 100
UJT: 2N2646 FET: BFW 11 DIAC: D32 TRIAC: BT 136 SCR: TYN 604
LED: 5 mm RED LDR: 5 mm Photo diode. Photo transistor: 2N5777
DC lamp 12 V with leads.
Required number of stackable 2mm patch cords and operating manual,
Feedback Amplifier trainer kit
A. DC power supply 12 V @ 500 mA
B. Four feedback amplifiers on panel
C. Voltage shunt, current shunt, voltage series & current series.
Built in rectifier from 230 (AC Supply)
Transistor Amplifier trainer kit
. On panel NPN transistor amplifier with Study of all amplifier
B. Variable power supply 0 to -12V @ 500 mA
C. Fixed power supply + 12 V @ 500 mA
D. On panel biasing network .Built in rectifier from 230 (AC Supply)
All types Oscillator trainer kit
Fixed DC supply of +5V/500mAOne LED indicator to indicate Power input.On-board
Circuits Hartley Oscillator circuit. Colpitt’s Oscillator circuit. Blocking Oscillator circuit.
Clapp Oscillator circuit. All interconnections are made using 2mm banana Patch cords.
Built in rectifier from 230 (AC Supply)
1
2
3
4
Lab. Title : - Electronics Devices & circuit lab
1
2
UJT Characteristics trainer kit
A. Two variable DC supplies 0 to 12 V & 0 to 5 V @ 500 mA,
B. On panel circuit diagram & UJT,
C. Two dual range digital panel meters.
D. Required numbers of patch cords and operating manual. Built in rectifier from 230
(AC Supply)
RECTIFIER TRAINER - Half & Full Wave Recitifier with
Filters.
A. On panel AC source of 9V- 0- 9V
B. On panel diodes, Capacitors, resistors & inductor
C. Required numbers of patch cords and operating manual. Built in rectifier from 230
(AC Supply)
Ohms law trainer with built in two digital meters.
A. Variable power supply 12 V@ 500 mA
B. On panel circuit diagram with three resistors
C. Two digital panel meters
D. Required numbers of patch cords and operating manual. Built in rectifier from 230
(AC Supply)
Transistor Characteristics (CE/CB/CC) trainer with
built in two digital meters.
A. Two variable DC supplies 0 to 15 V @ 500 mA,
B. On panel transistor & source resistance.
C. Two dual range digital panel meters.
D. Required numbers of patch cords and operating manual. Built in rectifier from 230
(AC Supply)
5
6
7
8
3
Branch : Electronics Engg.
Lab. Title : - Digital Electronics lab
2
1
All Flip Flop trainer kit
On panel gates : 4 NAND gates (7400), 4 NOR gates (7402),4 AND gates (7408), 4 OR
gates (7432) & 6 not gates (7404), 5 Logic input switches with green LED display,5
Logic output red LED display On panel bounce less pulser & clock generator On panel 5
sockets each for +5 V & GND.Built-in power supply DC +5 V @ 500 mA
Required numbers of patch cords and operating manual.
4-bit full subtractor & half subtractor trainer kit
Built-in power supply DC +5 V @ 500 mA
3 Logic input switches with green LED display
3 Logic output red LED display
Two and gates ( 7408 ), one OR gate ( 7432 )
Two not gates ( 7404 ) & Two EX-OR gates ( 7486 ) on panel Required numbers of
patch cords and operating manual
4-bit full adder & half adder trainer kit
Built-in power supply DC +5 V @ 500 mA
3 Logic input switches with green LED display
3 Logic output red LED display
Two and gates ( 7408 ), one OR gate ( 7432 )
Two not gates ( 7404 ) & Two EX-OR gates ( 7486 ) on panel
Required numbers of patch cords and operating manual
1
2
3
3
1
2
Logic training board on counters
4 bit ring counter using 7495
5 Logic input switches with green LED display
4 Logic output with red LED display
On panel pulser
Built-in power supply DC +5 V @ 500 mA
Required numbers of patch cords and operating manual
Encoder/decoder trainer kit
Built-in power supply DC +5 V @ 500 mA
3 Logic input switches with green LED display
3 Logic output red LED display on panel
Required numbers of patch cords and operating manual
Multiplexer & Demultiplexer kit
8- Line to 1-Line multiplexer using 74153/74152On panel address generator4 Logic
input switches with green LED display4 Logic output display On panel bounce less
pulser Built-in power supply DC +5 V @ 500 mA .Required numbers of patch cords and
operating manual
Shift Resistors ( SIPO, SISO, PIPO, PISO) Trainer
Built-in power supply DC +5 V @ 500 mA SIPO ( 74164 ), SISO ( 7491 ), PIPO ( 74194
) & PISO ( 74165 ) 19 Logic input switches with green LED display 16 Logic output
LED display On panel pulser
Required numbers of patch cords and operating manual.
4
5
6
7
3
Branch : Electronics Engg.
Lab. Title : -Electrical & electronics mesurment lab
2
1
Kelvin Double dridge
• Built-in bridge excitation oscillator at 1KHz
• Four primary arms provided to balance the bridge (Two arms are range selections)
• Two secondary arms are provided for range adjustment.
• Provisions to connect the unknown resistance at one arm
• Tolerance : ±5%
• Detector amplifier
• Provision for measurement of unknown resistance.
• Bridge sensitivity control through potentiometer.
Maxwell bridge trainer kit
• Built-in bridge excitation oscillator at 1KHz
• Detector amplifier
• Maxwell bridge with different values of resistors.
• Provision for measurement of unknown inductance.
• Bridge sensitivity control
Hay,s bridge trainer
Built-in bridge excitation oscillator at 1KHz
• Detector amplifier
• Hay’s bridge with different values of resistors.
• Provision for measurement of unknown inductance.
• Bridge sensitivity control
1
2
3
3
1
2
Branch : Electronics Engg.
OP-AMP AS ADDER & SUBSTRACTER KIT
1
2
3
OP-AMP AS INTERGRATOR & DIFFRENTIATOR KIT
OP-AMP AS FILTER (LPF, HPF, & BPF)
WEIN BRIDGE OSCILLATOR TRAINER
4
A/D CONVERTER TRAINER KIT
5
D/A CONVERTER TRAINER KIT
6
3
Lab. Title : -Analog Electronics lab
Instrument comprises of 3 DC Regulated Power Supply, of 0 - 1.5V/150mA (2 Nos.), ±
15V DC & Two Dual Range moving coil meters, different Resistance & Capacitors are
provided on the front panel
741 as Integrator & Differentiator Circuit, Built in power supply, patch chords and
operation manual
Low Pass Filter, High Pass Filter, Band Pass Filter ,Built In sine wave Generator, Built in
power supply, patch chords and operation manual
A. DC supply 12 V @ 500 mA
B. On panel transistorized wein bridge oscillator circuit diagram
C. Variable load resistors
D. Required numbers of patch cords and operating manual.
Three Input Switches
Fixed Clock
One LED indicator to indicate Power input.
On-board Circuits
Analog Circuits using ADC0808
Fixed AC power supply : 230 VAC
Built In power supply.
Patch chords and manual provided
Eight Input Switches
Fixed Clock • One Manual Pulser
One LED indicator to indicate Power input.
On-board Circuits
R-2R Circuit • Binary Weighted Circuit
Amplifier Circuit • DAC-0808 Circuit
Built In power supply.
Patch chords and manual provided
Branch : Electronics Engg.
Lab. Title : - Principle of Communication lab
2
1
Linear 1C trainer kit
A.
B.
C.
D.
E.
F.
AM (modulation /demodulation) trainer kit
A. AF Signal generator 1 KHz
B. Carrier generator 100 KHz
C. Amplitude modulator
D. Amplitude demodulator
E. Power supply +/- 5 V@ 500 mA
F. Required numbers of patch cords and operating manual.
FM (modulation/demodulation) trainer kit
A. AF Signal generator 5 KHz
B. Carrier generator 200 KHz
C. Frequency modulator
D. Frequency demodulator
E. Power supply +/- 12 V@ 500 mA
F. Required numbers of patch cords and operating manual.
Pulse Modulation trainer kit
A. AF Signal generator 1 KHz
B. Carrier generator 8 & 16* KHz
C. PAM modulator & PAM demodulator
D. Power supply +/- 12 V @ 500 mA
E. Required numbers of patch cords and operating manual
1
2
3
4
3
Built-in fixed DC power supplies of GND, +12V, -12V & +5V @ 500 mA,
Resistor bank (22 nos), Capacitor bank (12 nos) & potentiometer bank (5nos)
Different ICs on panel with sockets for individual pins,
ICs: 723, 710, 565, 555, 566, & 741,
Sockets used: 2mm,
Required number of stackable patch cords and operating manual,
1
2
Ask modulation and demodulation trainer kit
Data clock generator
Carrier generator
ASK modulator & ASK demodulator
Power supply +/- 12 V & +/- 5 V @ 500 mA
Required numbers of patch cords and operating manual.
FSK modulation and demodulation trainer kit
Modulating signal generator using 7490 Carrier generator FSK modulator & FSK
demodulator Power supply +/- 12 v & +/- 5 v @ 500 maRequired numbers of patch
cords and operating manual.
PSK modulation and demodulation trainer kit
Modulating signal generator using 7490
Carrier generator
. PSK modulator & PSK demodulator
. Power supply +/- 12 v & +/- 5 v @ 500 ma
. Required numbers of patch cords and operating manual
ANALOG SIGNAL SAMPLING AND
RECONSTRUCTION.
AF Signal generator 20 Hz to 20 KHz, 5 V p-p
Clock generator 2 KHz to 32 KHz to study:
i.
Sample and hold
ii.
Natural sampling
iii.
Flat top sampling
Sampling clock width control 10% to 90%
Low pass filter ,Power supply +/- 12 V. 500 mA and +/- 5 V, 500 mA ,Required numbers
of patch cords and operating manual.
5
6
7
8
3
Branch : Electronics Engg.
1
Lab. Title : - Microprocessor Lab
2
8085 MICROPROCESSOR TRAINER
• CPU 8085 Operating at Crystal Frequency of 6.14MHz.
• RAM 6264 with Battery Backup.
• EPROM
• Keyboard Controller.
• LCD DISPLAY.
• RS 232 INTERFACE.
• TIMER/ COUNTER.
• PROVISION FOR INTERFACE.
• POWER SUPPLY: EXTERNAL OR INERNAL.
• ADDRESS, DATA LINE TO BE AVAILABLE IN FRC CONNECTOR.
8051 MICROCONTROLLER TRAINER
CPU 8051 OPERATING AT 10/12 MHz
• BATTERY BACK UP RAOM UPTO 16KB.
• MONITOR EPROM.
• ASCII KEY BOARD INTERFACE.
• LCD DISPLAY.
• RS 232 INTERFACE.
• ON BOARD ASSEMBLER/DISASSEMBLER
• TIMER/ COUNTER.
• PROVISION FOR INTERFACE WITH PC.
• POWER SUPPLY: EXTERNAL OR INERNAL.
• ADDRESS, DATA LINE TO BE AVAILABLE IN FRC CONNECTOR.
1
2
3
Branch : Electronics Engg.
Lab. Title : - T.V & Audio Engineering & Acoustics Lab
2
1
TV. trainer kit (Monochrome )
CCIR-B-PAL-G, 625 Lines Channels : 230 2-4VHP: I (VL), 5-12VHPIII (VH) 12 100:BANDIV&V, else : SBAND & HYPERBAND Picture Tube Size : 36cms.Diagonal RF
Input Impedance : 75W Circuit Blocks : System Control Circuit, Video IF, Sound, Tuner
Section, Horizontal Oscillator, Horizontal Output, Vertical Oscillator, Vertical output,
Video & Chroma Section, Power Supply, AV sections ON Screen Display to set : Volume
Brightness, Contrast, Colour Channel &Band Selection Tuning Panel Control : ON-OFF
Switch, Stand by Menu Vol + / - Prog + / - Remote Control Function : Volume,
Brightness, Stand by, Colour, Contrast, Channel Selection, Audio Mute, AV Mode, Zoom,
Swap, Scan Child Lock PCB Size : 475 x375mm No. Pf Faults : 21 No. of test Points : 55
I.F. Frequency : Video - 38.9MHz,Audio - 33.4MHz Speaker Size : 50 x125mm
Accelerating Potential : 24KVmax Operating Voltage for EHT : 110V Mains Supply :
230V± 15%, 60Hz on request Power Consumption : 75VA(Approx).
VCR trainer kit
230v + 10% AC, 50Hz single phase. 2. Power consumption : 30 watts. 3. Recording
format : VHS. 4. Video Heads : 3 Heads. 5. TV System : CCIR - PAL - B/G - 625 Line. 6.
Playback system : Rotary-2-head helical scan. 7. Playback output : VHF Channel 3 or 4. 8.
Tape Speed : 23.39 mm/sec. 9. Timer : 100 Year Calendar, 8 programs, 1 month time.
10. Tuner Channels : VHF-2 to 12, UHF-21 to 68. 99-channel position can be
preprogrammed. 11. Basic Features : PLAY, FF, REW, STILL, PIC SEARCH, STOP, SHARP
SOFT, TV/VTR, and TRACKING. 12. Auto facilities : Auto Power ON, Auto rewind, Auto
eject, Auto power OFF, Auto eject, Auto cue and play. 13. Other facilities :
Memory/Repeat/Search facility Lapse time counter & Noise filter. One touch recording.
14. Distortion : 10 to 15% 15. Standard Accessories : 1. Video cassette - E180 2. R.F out
put cable 3. Instructional cum teaching manual
Radio receiver trainer kit (super heterodyne)
Power supply : 220V Ac, 50Hz 2. Audio power output : 450mw maximum. 3. Frequency
range : MW - 520 - 1620 Khz. 4. Intermediate Frequency : 455 KHz 5. Input Circuits : 1)
RF Amplifier,2) Mixer,3) Local Oscillator, 4) IF Amplifier 5) Tuning : With Variable
Capacitor (ganged) 6) detector with AGC control
1
2
3
3
1
2
COLOR TV TRAINER
CCIR-B-PAL-G, 625 Lines Channels : 230 2-4VHP: I (VL), 5-12VHPIII (VH) 12 100:BANDIV&V, else : SBAND & HYPERBAND Picture Tube Size : 36cms.Diagonal RF
Input Impedance : 75W Circuit Blocks : System Control Circuit, Video IF, Sound, Tuner
Section, Horizontal Oscillator, Horizontal Output, Vertical Oscillator, Vertical output,
Video & Chroma Section, Power Supply, AV sections ON Screen Display to set : Volume
Brightness,Contrast, Colour Channel&Band Selection Tuning Panel Control : ON-OFF
Switch, Stand by MenuVol + / - Prog + / - Remote Control Function : Volume, Brightness,
Stand by, Colour, Contrast, Channel Selection, Audio Mute, AV Mode, Zoom, Swap,
Scan Child Lock PCB Size : 475 x375mm No. Pf Faults : 21 No. of test Points : 55 I.F.
Frequency : Video - 38.9MHz,Audio - 33.4MHz Speaker Size : 50 x125mm Accelerating
Potential : 24KVmax Operating Voltage for EHT : 110V Mains Supply : 230V± 15%,
60Hz on request Power Consumption : 75VA(Approx).
MICROPHONE TRAINER
Power Output : 100W RMS at 10% THD
Pre-amplifier Output : 200mV
Line output : 1V/ 1KW
Input Channels : Mic: 5nos; 0.65mV/ 4.7KW
Aux: 2 nos; 50 mV & 150 mV/
470KW
Frequency Response : 65 Hz to 15 KHz +/- 3dB
Tone Controls : Bass, Treble, Master Control
Speaker Outputs : 4W, 8W, 16W, 70-100V Line
Matching
Speakers : 2 nos
Microphones : 2 nos (Dynamic)
Mains Supply : 230V AC ± 10%, 50/60Hz
4
5
3
Branch : Electronics Engg.
Lab. Title : - Basic Electronics lab
2
1
FUNCTION GENERATOR
Frequency range: 0.1-3 MHz.
Voltage Display : 0-10V
Accuracy 1% or better
Operating Modes:Sine ,Square,Triangle,DC Output.
Pulse Duty Cycle Variable
Frequency Counter 50 MHz
Output Voltage 20 Vpp.
Low signal distortion.
Digital display : Seven Segment or LCD for Frequency as Well As Amplitude
Power Supply:220 V +10 %,50 Hz/60 Hz.
70 MHz Digital Storage Oscilloscope
• 70 MHz bandwidth Dual Channel, • 1 GS/s sample rate on all channels,• 2.5k point
record length on all channels,• 7 inch WVGA (800X480) Active TFT Color Display,• 34
automated measurements,• Dual window FFT, simultaneously monitors both the time
and frequency domains.,• Zoom Function,• Autoset and signal auto-ranging,• USB
Interface on front and rear panel.
DIGITAL MULTIMETER
VOLTAGE : 0-1000VDC, 0-750V AC ACCURACY 1% Or Better
CURRENT : 0-10A AC/DC ACCURACY 2% Or Better
RESISTANCE : 0-30M Ohms.
CAPACITANCE : 10uF - 100uF
TEMPERATURE MEASUREMENT
FREQUENCY MEASUREMENT
MICRO AMP MEASUREMENT
NPN & PNP TEST
DIODE & CONTINUITY TEST
AUTO RANGING
LARGE DISPLAY & PROTECTION COVER
Bread Board with power supply
230v ,50 hz, +5v,+12v power supply, different block patch cords and operating manual
1
2
3
4
3
BRANCH-CHEMICAL ENGG.
Lab Title:
S.No
Name of the Equipments
Specifications
2
1
3
Sieve shaker (Gyratory Type) with set of screen
1
2
1. MECHANICAL OPERATION LAB
Ball Mill
Set of sieves 200mm dia and 35 mm height of the each sieves should conform to ASTM
std. The sieve designation should be std(b)850,600,425,300,212,106,75 , 53 and 38
micron .with lid and receiving pan The shaker should be motorized of suitable capacity
to carry 7 sieve of 20 cm dia.of above designated sieve
Cylinder should be made of MS size -300 x300 mm, capacity-5kg , rotation speed-80rpm
power supply-220-320 Volt Feed size-5mm ,product size-200 mesh
Jaw crusher
The jaw crusher should be made of manganese steel with hopper for feeding material
with section 01 no. Max. size for feed 50mm ,product discharge size 5mm ,capacity100-200 kg/hr jaw size -100x150 mm Motor drive single phase 440V. 3.0 HP motor .
Plate and frame filter press
Plate size-200mm X200mm , filter cake capacity-.19cubic feet ,filtration area 1.7 feet
square .feed rate-.8-1.7 GPM ,slurry pressure-60 psi , slurry tank - 40-60 lit. With stirrer
and gear pump . frame-6 plate -7 . Overhead water tank 20- 30 lit.
3
4
TITLE:- 2 CHEMICAL INSTRUMENTATION
PH (digital meter)
PH reading -0-14pH ,resolution -.O1pH , power suppy-230 V A.C. sensor elctrode- glass
type , Tem range 0- 100deg.C display 3 1/2 digit LED display . With calibration facility
Bimetallic thermometer
constant temp.- 0-100 c both electrical element made by metal thermometer
electrode -ice pot type glass
Calibration thermometer using thermocouple
temp. range- 0-50 K , Accuracy-+0.3to -0.3 K sensor type-thermocouple "K" Type
1
2
3
TITLE :-3 FLUID MECHANICS & HEAT TRANSFER LAB
S.No
Name of the Equipments
Specifications
U tube manometer
1
Orificemeter , Venturimeter & Rotameter setup
2
Reynold experiment setup
3
"U" Tube type primary standard manometer used for precision measurement of
pressure, differential pressure. Nominal length -200-2000mm, water column pressure0-20KPaHg column pressure -0-50 K Pa ,media compatibility-glass
fitted with Venturimeter, orifice meter and rotameter to determine the coefficient of
discharge . Orifice plate placed between two flanges with an orifice of suitable Do/Dp
ratio. material-acrylic ,sump tank capacity-50 lit. electric supply-230V ,water circulation
with FHP pump venturimeter for 1" pipe line - Convergent cone-15-17 deg, Divergent
cone-5-7 deg. ,throat dia -1.5-1.8 cm ,Differential manometer tapping at throat &
upstream , with compatible rotameter and measuring tank of 25 lit. capacity and 0.5 hp
circulation pump of standard make . Tanks should be made of SS.
The set up should be for determination of Reynolds’s no. The apparatus should consist
of a glass tube with one end having bell mouth entrance ,connected to a constant
headwater tank ,and the other end a valve should be provided to vary the flow rate,
the tank should be of sufficient capacity to store water; a capilary tube should be
introduced centrally in the bell mouth for feeding dye from a small container placed at
the top of the tank tube material-borosilicate glass ,constant head water tank capacity20-40 lit. Sump tank-50-60 lit. Power supply single ph ,220v 0.3 KW . The pumps should
be of reputed make.
TITLE-4 MASS TRANSFER LAB
Simple Batch Distillation
Should consist of flow measurement device such as rotameter ,distillation still of 5lit
cap. condenser sump tank of 50-100 lit pump for water circulation , ,distillate tank,of
atleast 2lit cap. heater of nichrome temp range 0-200 deg c RTD PT 100 type digital
temp indicator , temp sensor the main units should be made of SS .power supply 1ph
220 v , 2kw
Natural Draft Tray Dryer
consist of stainless steel insulated drying chamber of size 30X 30X 30 cm . Fitted with
digital weighing balance 0-1000gm , and nichrome heater and temp sensor of RTD PT
100 type fitted with digital temp control panel Power supply- 1 ph ,230V, 2-3 kW-
1
2
BRANCH - CIVIL ENGG.
Branch : Civil Engg.
S.No
Lab. Title : - Building construction & Material Testing .lab
Name of the Equipments
Specifications
2
3
1
Cylindrical mould
Cylindrical mould, cast iron, Split150 mm dia 300mm
Enamel Tray
Slump test apparatus
Enamel Tray size 450 x 300 mm
Slump test apparatus with Temping rod, base plate (Dimension of Slump Cone- Bottom
Dia-20 cm, Top Dia-10cm, Height-30cm)
4
Tray
Tray size 650 x 500 x 50 mm
5
Vicat apparatus
Vicat apparatus test weight of 300 g.(1mm Dia Needle & 10mm Dia Plunger)
6
Compaction factor apparatus
Compaction factor apparatus 16mm x 600mm
7
Cube moulds
Cube moulds
Cube moulds 75mm x 75mm x 75 mm
Cube moulds 150mm x 150mm x 150 mm
1
2
3
8
Branch : Civil Engg.
2
3
Automatic Level-24x with aluminum tripod and
telescopic staff
Automatic Level-24x with aluminum tripod and telescopic staff Length 215mm
(8.46in.)
Magnification 24x,Objective aperture 32mm (1.26in.),Resolving power 4"
Field of View(at 100m/328ft.) 1°25'(2.5m / 8.2ft.)
Minimum focus 0.2m (7.9in.) from end of telescope,0.3m (1ft.) from instrument
center
Image Erect,Reticle pattern Cross line,Stadia constant 0,Stadia ratio 100
Focusing knob 1-speed,Sighting aid Gun sight
Accuracy (standard deviation for 1km double run leveling)
Without micrometer 2.0mm
Pendulum compensator with magnetic damping system
Setting accuracy 0.5",Working range ±15'
Sensitivity 10' / 2mm,Horizontal circle Diameter 103mm (4.1 in.)
Graduations 1° / 1gon
Horizontal motion drive Clamp less, endless, double-sided knobs,Water resistant
Operating temperature -20 to +50°C
Digital Theodolite-
Digital Theodolite-Stadia ratio 100,image erect, magnification 30 x, effective
aperture 45 mm, field of view 1°30",stadia constant 0,accuracy 1”,display 2 side,
resolving power 3",length of tube 157 mm with aluminum stand and other
accessories
1
1
2
Lab. Title : - SURVEY .lab
Branch : CIVIL Engg.
Lab. Title : Concrete Technology Lab
2
1
Cement Autoclave Apparatus
1
215 deg. C,2000 Watts, 50 Hz, single phase.
Aggregate crushing value apparatus-
Aggregate crushing value apparatus- Consists of M.S. Cylindrical Container
150mm +/-0.5mm dia x 130mm to 140mm high with base plate 200 to
230mm/sqr x 6mm thick. A Plunger of 148mm +/-0.5mm dia x 100 to 115mm
high. Supplied complete with Tamping Rod, 16mm dia x 600mm long, both ends
rounded, 1 no. Metal Measure 115+/- 0.5mm dia x 180 +/- 0.5mm high.
Flow Table Apparatus (Motorised)
Flow Table Apparatus (Motorised) Consists of a steel table top 76.2cm dia.,
finely machined with ribs and support,steel cam to lift and drop by 12.5 mm,
Conical mould with tamping rod.
2
3
Branch : CIVIL Engg.
1
Lab. Title : Material Technology Lab
2
3
Air permeability Apparatus
Air permeability Apparatus-The apparatus consists one each of permeability cell
12.5mm I.D. manometer 'U' type mounted on stand with a built in stop cock,
perforated disc, plunger rubber stopper, rubber tube 30cm long. Packet of 12
filter paper disc and a bottle of 100ml dibutylphthalate liquid with accessories.
Briquette testing machine-
Briquette testing machine- capacity 9 kN,One standard briquette mould
(single)with base plate.Suitable of operation on 230 V,50 Hz, single phase
supply.
1
2
3
Cement Autoclave Apparatus -Dia 150mm x Depth 500mm,working pressure 21 kg/cm2 at
Branch : Civil Engg.
2
1
Constant Head Permeameter1
Variable Head Permeameter-
2
Soil Lathe motorized3
4
5
Sampling Tube
Extractor frame Hand operated Sieve set .
6
Thermostatically controlled Hot air Oven
7
Lab. Title : - Soil mechanices..lab
3
Constant Head Permeameter-Constant head permeameter cell 75 mm and 114
mm dia,manometer tubes,constant level tank with accessories.
Variable Head Permeameter-permeability cell 4” dia,manometer tubes with
accessories Permeability cell ,Inside diameter: 100 mm,
Stand with ,4 manometer glass tubes 1500 mm: 21, 12, 5 and 3.5 mm inside
diameter,Wooden panel dimensions: 1680x280 mm
Soaking reservoir Made from plated steel Complete with overflow tube
Dimensions: dia. 230 mm x 230 mm high
Vacuum control panel Used for the saturating the samples. Complete with:
Adjustable vacuum valve,Vacuum gauge
Soil lathe consist of a cabinet enclosing motor and gear system with disk and
gripper plate of various size. Arrangement provided to control height and depth
of cutting tool through a lead screw which has speeds 0.8mm/min. And
1.6mm/min. Supplied complete with gripper plate pairs for 38mm, 50mm, 75mm,
and 100mm dia specimens.
Sampling Tube-for collecting undisturbed samples of 38 mm dia
Extractor frame Hand operated - for 38mm,50mm,75mm,100mm dia specimen
Sieve set with pan- 80mm,40mm, 20mm, 10mm, 4.75mm, 2mm, 1mm (GI frame 30 cm
dia) Brass frame 20cm dia-600micron, 425micron, 300micron, 212micron, 150micron,
75micron with pan.
Thermostatically controlled Hot air Oven (50 degree centigrade to 250 degree
centigrade)
Inner chamber made of S.S.and outer made of Mild Steel with Powder coating.
Gap between the walls fitted with glass wool insulation to avoid heat loses.
Heating elements made of high grade chrome plated nicrome wire.
Temp. controlled by thermostat. Temp. range 50°C to 250°C and Accuracy: +-2°C.
Air Ventilation provided on the top of the unit to remove the hot gases / fumes.
All the control switches & pilot lamps fitted on the front panel.
Trays should be supplied with G.I.wire mesh.
Branch : Work shop Engg.
1
2
Lab. Title : - WELDING SHOP TOOLS & EQUIPMENTS
3
1
2
3
4
5
6
7
8
9
10
11
12
Ball Peen Hammer
Blow Lamp
Electric Soldering Iron
Stainless Steel scale
Shear Machine
Elec. Arc welding Transformer .
Apron Leather
Screw Driver .
Screw Driver
Cross Peen Hammer
Pliers
File Flat Bastered
Ball Peen Hammer 500 gm with wooden handle
Blow Lamp of ½ lit Tank Capacity
Electric Soldering Iron 125 watt
Stainless Steel scale 12’’ Aching & printing in inches & mm
Shear Machine Shear Up to 6 mm Thick sheet ( hand shear m/c)
Elec. Arc welding Transformer Single & Double Phase 450 amp.
Apron Leather 24’’x 36’’
Screw Driver engg. Pattern 3 mm dia & 65 mm length (Pie, Taparia, Inder)
Screw Driver engg. Pattern 4.5 mm dia & 75 mm length (Pie, Taparia, Inder)
Cross Peen Hammer 500 gm with handle (Gedore, Pie, Taparia, Inder)
Pliers 6’’ combination Heavy Duty (Gedore, Pie, Taparia, Inder)
File Flat Bastered 12’’ (Jhalani, Pie, Taparia, Inder)
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Fitters Bench Vice
Fitters Bench Vice (6 x 150) no & mm heavy duty double rib (Gedore, Pie, Taparia, Inder)
Hand Drilling Machine
Hand Grinder Portable
Oxy Acetylene Welding torch
Welding shield
Pipe Wrench
D/E Fix Spanner set
Adjustable wrench small
Adjustable wrench
TIN Cutter
Smith Try Square
Welding cable
Electrode Holder
Welding cable luges
Number punch
Smithy Tong
Hand Drilling Machine ½’’Size Wolf , Bosch
Hand Grinder Portable 4” size Wolf Bosch (AG-4)
Oxy Acetylene Welding torch & nozzle set, high pressure weld up to 30 mm
Welding shield (Hand screen)
Pipe Wrench 12” (300 mm). (Gedore, Pie, Taparia, Inder)
D/E Fix Spanner set (10 Nos) 6 mm to 27 mm drop forged (Gedore, Pie, Taparia, Inder)
Adjustable wrench small 8" chrome platted (Gedore, Pie, Taparia, Inder)
Adjustable wrench 10” chrome platted (Gedore, Pie, Taparia, Inder)
TIN Cutter 12” straight jaw.
Smith Try Square 18" x12" (Gedore, Pie, Taparia, Inder)
Welding cable 600 Amp /mt.
Electrode Holder for Arc Welding 600 Amp
Welding cable luges Brass/ Copper heavy duty
Number punch set (0-9) 5 mm size (Gedore, Pie, Taparia, Inder)
Smithy Tong (flat mouth) 12" size
Branch : Work shop Engg.
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
2
Iron Smoothing plane
Cast steel Hand saw
Hand saw
Cast steel tennon saw
Compass saw
Firmer chisel
Firmer chisel
Firmer Edge chisel
Firmer chisel
Dovetail chisel
Mortise chisel
Mortise chisel
Mortise chisel
Try square .
Mallet (Wooden) .
Tee Bar Cramp
Gimlet
Gimlet
Spring Divider
Outside Firm Joint calliper
Adze .
Pincer
Flate Basterd File
Half Round Basterd File
Rasp Cut Half Round File
Round Basterd File
Triangular File
Triangular File
Lab. Title : - CARPENTRY SHOP TOOLS & EQUIPMENTS
3
Iron Smoothing plane 9”x2” with cutte.(sole 2", 2" blade) (Anant Make)
Cast steel Hand saw 18” (Rail Poster)
Hand saw 12” (Rail Poster)
Cast steel tennon saw 10” with handle (Rail Poster)
Compass saw 16”
(Rail Poster)
Firmer chisel 1" size with handle (Egale/Fish)
Firmer chisel ¾” with handle (Egale/Fish)
Firmer ½” with handle
(Egale/Fish)
Firmer chisel 1/8” with handle (Egale/Fish)
Dovetail chisel ¾” with handle (Egale/Fish)
Mortise chisel 1” with handle (Egale/Fish)
Mortise chisel 1/2 ” with handle (Egale/Fish)
Mortise chisel 1/4” with handle (Egale/Fish)
Try square 12" stainless steel blade . (G.V.S)
Mallet (Wooden) 500 gm approx.
Tee Bar Cramp (4’ Length) (Taparia)
Gimlet (Screw Auger ½’’) (Taparia)
Gimlet (Screw Auger 3/8”) (Taparia)
Spring Divider 6”
Outside Firm Joint calliper 6”
Adze (3” angle Edge).
Pincer 8” .
Flate Basterd File 12” Single cut & double cut (2 each)
Half Round Basterd File 12” Single cut & double cut (2 each)
Rasp Cut Half Round File 12”
Round Basterd File 12” x ½”
Triangular File (slim taper) 6”
Triangular File 4”(Slim taper)
2
1
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
3
Carpentry Bench Vice
Adjustable Spanner
Double end Spanner Set
Carpentry Bench Vice 7”x 9” quick release, front dog heavy duty .
Adjustable Spanner 12” .
Double end Spanner Set (Six Piece) 6 mm - 7mm to 16mm - 17 mm drop forged chrome
plated (Pie, Jhalani, Tapria, Inder)
Screw driver
Screw driver
Number punch set
Number punch set
Universal wood working machine
Screw driver Engg. Pattern 10 mm dia 18" size (Pie, Jhalani, Tapria, Inder)
Screw driver Engg. Pattern 10 mm dia 10" size (Pie, Tapria, Inder)
Number punch set 0 to 9- Size ¼”
Number punch set A to Z- Size ¼” latter punches
Universal wood working machine electric motor Three phase goutar) Aswani, Sarswati
Make or equivalent . Bedsize 4' . Sph rpm 1440
Carborundum Universal stone
Cross Peen hammer
Rasp cut file
Twist Drill HSS bit
Working table(wooden)
Working table(metal with wooden)
Steel rule
plastic hammer
measuring tape (steel / canvass)
Carborundum Universal stone (Oil stone) 6” x 2”x 1”
Cross Peen hammer 800 gm with wooden handle
Rasp cut file (8”)
Twist Drill steel bit 1/4" , 5/32" , 3/16", 1/8", 5mm & 10 mm parallel sank
Working table(wooden) size 6'x4'x3' heavy duty
Working table(metal with wooden) size 6'x4'x3' heavy duty
steel ruler 12" Inches and mm graduated
plastic hammer(double phase) plastic with metal
measuring tape 5mt. (Steel / Canvas )
Branch : Work shop Engg.
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
22
Pipe vice
Chain spanner
Pipe wrench Pipe wrench
Pipe wrench
Pipe wrench
Pipe wrench
Chain pulley
Tripod 10ft.
Hack saw frame
Sleigh wrench
Pliers (Plash)
Screw driver
Screw driver
Feet spanner
Feet spanner
Chisel
Hammer
Lifter
Cross spanner
Pipe dye
2
Lab. Title : - PLUMBING SHOP TOOLS & EQUIPMENTS
3
Pipe vice (1/2",3/4",1",2") (GVS/TATA)
Chain spanner - 18"(6 no.) (EVEREST/JHALANI/TAPARIYA/GVS)
Pipe wrench - 10" (EVEREST/JHALANI/TAPARIYA/GVS)
Pipe wrench - 12" (EVEREST/JHALANI/TAPARIYA/GVS)
Pipe wrench - 14" (EVEREST/JHALANI/TAPARIYA/GVS)
Pipe wrench - 18" (EVEREST/JHALANI/TAPARIYA/GVS)
Pipe wrench - 24" (EVEREST/JHALANI/TAPARIYA/GVS)
Chain pulley - 1.5 MT (MAKE INDIA)
Tripod 10ft.(for submersible) 1set.
Hack saw frame 12" (TATA/GVS)
Sleigh wrench - 10" (TATA/GVS)
Pliers(Plash) 6/8" (TATA/GVS)
Screw driver - 6" (TATA/GVS)
Screw driver - 12" (TATA/GVS)
Feet spanner - 14/15 (TATA/GVS)
Feet spanner - 20/22 (TATA/GVS)
Chisel - 6" (TATA/GVS)
Hammer - 1Kg (TATA/GVS) Ball peen hammer with wood handle.
Lifter - 1.25" (EVEREST/JHALANI/TAPARIYA/GVS)
Cross spanner 10" (TATA/GVS)
Pipe dye 1/2", 3/4", 1" (GVS)