Download PFCI 100 115 HF

PFCI 100-115 HF
Power Factor Corrector
100W
Input/output isolated
Wide input range: 85 - 132VAC / 360-800Hz
 High efficiency up to 82%
 Compact size: 4,6" x 2,4" x 0.78"
 0,97 Power factor
 EN 55022 Class A.
 CE Mark for LVD
With the PFCI series, CONVERGIE is introducing a new concept
of Power Factor Corrector. Through its I/O isolation, an integrated
filter and an integrated signal generation, this module is designed
to reduce product development time and minimize the number of
external components.
The PFCI series is available in 2
different models with 2 output voltages,
24 or 48V.PFCI is characterized by
conformity to safety standard and is well
suited for use in distributed power
system.
POWER FACTOR CORRECTOR
Input Specifications
MODEL
Output Specifications
min.
max.
nom.
Frequency
Vout1
Iout1
power
(VAC)
(VAC)
(VAC)
(Hz)
(VDC)
(A)
(W)
PFCI 100-115 HF
85
132
115
360-800
24
4,2
100
PFCI 100-115 HF
85
132
115
360-800
48
2,1
100
CONNECTION DIAGRAM
PFCI 100-115 HF
Electrical Specifications
Condition
PFCI 100-115 HF
Tc = -40 to + 85°C
Iout = 0 to 100%
time period = 0,1s
Vin nom.
Vin min.; Iout max.
see note1
see note2
Vin min. to Vin max.
BW=20MHz
see note3
Vin nom.; Iout nom.
Fixed
1 Min.
In / Out
1 Min.
1 Min.
see note4
Ta
Ts
Tc
UL94V-0
Ground Bening; Ta = +25°C
115V
360 to 800 Hz
85 to 132V
140V
40mA
1,50A
±10%
±10%
±10%
110% to 150%
±10%
YES
YES
75 VAC to 85 VAC
0,97
+/-0,02%/°C
<1 ms
82%
120Khz
2500 VAC
1500 VAC
500VAC
4°C/W
Tc > 110°C
-25°C to +70°C
-40°C to +105°C
+ 100°C
Aluminium substrat with plastic box
>500000 h
300g
Power Factor Corrector
Parameters
Nominal input voltage
Input Frequency
Input over range
Input over voltage
No load input current
Input current max.
Output voltage accuracy
Load régulation
Line régulation
Limitation range
Output ripple peak to peak
Parallel boost
Remote ON/OFF
AC FAIL
Power Factor
Temperature coefficient
Transient response time
Efficiency
Switching Frequency
Isolation Input/Output
Isolation Input/Case
Isolation Output/Case
Thermal Impedance
Thermal Protection
Operating temperature range
Storage temperature
Maximum base plate temp.
Case material
MTBF (MIL-HDBK-217-F)
Weight
All specifications are typical, 25°C ambient , with nominal input voltage and underfull output load conditions, unless otherwise stated.It is
recommended to protect the input by fuses or other protection devices. Fuses are never supplied internally, and without them, severe damage or even
fire can occur in the event of a module failure. A slow fuse with a rating of 2x the Iin max. is recommended. In low noise applications it is
recommended that a low ESR capacitor be placed across the input pins, and output pins.
Pin connections
Note 1: To obtain the voltage accuracy, a capacitor should be placed across the output pins as
shown on the diagram connections, recommended value is 3300 µF/50 V.
Pin Number
3
6
9
11
12
13
14
15
16
18
CONVERGY
N
L
+VS
-VS
SD GND
AC FAIL GND
SD
AC FAIL
-VS
+VS
Note 2: Load regulation is specified from 70% load to full load for the PFCI 100-115.
Note 3: 50 to 100% within 1% Vo.
Note 4: Application note THERM PFCI provides detailed thermal considerations.