Download Class A Output Stage

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Carbon nanotubes in photovoltaics wikipedia , lookup

Operational amplifier wikipedia , lookup

Power MOSFET wikipedia , lookup

Transistor–transistor logic wikipedia , lookup

Opto-isolator wikipedia , lookup

Current mirror wikipedia , lookup

CMOS wikipedia , lookup

Amplifier wikipedia , lookup

Valve RF amplifier wikipedia , lookup

Power electronics wikipedia , lookup

Audio power wikipedia , lookup

Radio transmitter design wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Rectiverter wikipedia , lookup

Transcript
Class A Output Stage - Recap




Class A output stage is a simple linear current
amplifier.
It is also very inefficient, typical maximum
efficiency between 10 and 20 %.
Only suitable for low power applications.
High power requires much better efficiency.
Why is class A so inefficient ?




Single transistor can only conduct in one
direction.
D.C. bias current is needed to cope with
negative going signals.
75 % (or more) of the supplied power is
dissipated by d.c.
Solution : eliminate the bias current.
Class B Output Stage
Q1 and Q2 form two unbiased emitter followers

Q1 conducts only when the input is positive

Q2 conducts only when the input is negative

Conduction angle is, therefore, 180°

When the input is zero, neither conducts

i.e. the quiescent power dissipation is zero
(We are temporarily ignoring the need to FWD
Bias the BE junctions for conduction to occur, which
causes “crossover distortion” in the output.)

Class B Current Waveforms
Iout
time
IC1
Ideal waveforms shown.
-ignoring
“crossover distortion”
IC2
time
time
Class B Efficiency
Average power drawn from the positive supply:
IC1
Pve   VCC I C1
^
Vo/RL
0
p
2p
Phase, q = wt
A sin(q)
Waveform of + supply
current has avg. value
given by peak/pi
^
VCC V0
 Pve  
p RL
By symmetry, power drawn from +ve and –ve
supplies will be the same.
Total suply power, therefore:
^
PS  Pve   Pve   2 Pve 
2VCC V0

p RL
The average load power will be
Efficiency
^
^
PL (Vo ) p RL
p Vo
 

^
PS
2 RL 2 V V
4 VCC
CC o
2
Max efficiency occurs for ^
Vo = VCC
and equals pi/4 = 0.75 =75%
(In actual practice max. value is limited to
Vcc – VCE sat  VCC)
Max. avg.load power is found by subst. Vo = VCC
into equation for PL above
and equals (1/2 ) (VCC)2/RL
^


 NB. Vo  VCC    p / 4  78.5% 


Power Dissipation
To select appropriate output transistors, the
maximum power dissipation must be calculated.
Just need to find the maximum value of PD to select
transistors/heatsinks
For Class B quiescent power dissipation = 0
(it was max. under quiescent conditions for Class A)
When an input signal is applied the avg. power
Dissipated in the Class B stage is
Subst. For Ps and PL from eqns. on previous page
(eqn 9.19)
To find maximum differentiate
Subst this value in eqn. (9.19) yields
Thus
(From symmetry half the total PD is dissipated in each
transistor.)
We can find the efficiency at the point of max power
dissipation by subst.
into the eqn. for Class B efficiency to get  = 50%
Plotting eqn. (9.19), which gives avg. power
dissipated vs. output signal amplitude, shows that
power dissipation decreases after it it reaches
a maximum while operating at a higher signal
amplitude. However, at higher signal amplitudes
there is greater nonlinear distortion as a result of
approaching saturation in the transistors.
Example
It is required to design a class B output stage to
deliver an average power of 20W to an 8 ohm load.
The power supply voltage VCC is to be 5 volts
greater than the peak output voltage.
Determine:
the supply voltage required.
the peak current drawn from each supply,
the total supply power,
the power conversion efficiency,
the maximum power that each transistor can dissipate
safely.
Solution:

Thus
= 18 + 5
Example (Cont’d)
Efficiency / Power Dissipation
Peak efficiency of the class B output stage is
78.5 %, much higher than class A.

Unlike class A, power dissipation varies with
output amplitude.

Remember, there are two output devices so
the power dissipation is shared between them.

Cross-Over Distortion





A small base-emitter
voltage is needed to turn
on a transistor
Q1 actually only conducts
when vin > 0.5 V
Q2 actually only conducts
when vin < -0.5 V
When 0.5 > vin > -0.5,
nothing conducts and
the output is zero.
i.e. the input-output
relationship is not at all
linear.
Actual Input-Output Curve
vout  vin  VBE
vout  vin  VBE
Effect of Cross-Over Distortion
Efficiency / Power Dissipation



Peak efficiency of the class B
output stage is 78.5 %, much
higher than class A.
Unlike class A, power
dissipation varies with output
amplitude.
Remember, there are two
output devices so the power
dissipation is shared between
them.
Class B Summary



A class B output stage can be
far more efficient than a class A
stage (78.5 % maximum
efficiency compared with 25
%).
It also requires twice as many
output transistors…
…and it isn’t very linear; crossover distortion can be
significant.