* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download BD9722FV - uri=media.digikey
Electric power system wikipedia , lookup
Electromagnetic compatibility wikipedia , lookup
Pulse-width modulation wikipedia , lookup
Electrical ballast wikipedia , lookup
Three-phase electric power wikipedia , lookup
Power inverter wikipedia , lookup
Current source wikipedia , lookup
Ground (electricity) wikipedia , lookup
Power engineering wikipedia , lookup
Semiconductor device wikipedia , lookup
Schmitt trigger wikipedia , lookup
Electrical substation wikipedia , lookup
History of electric power transmission wikipedia , lookup
Variable-frequency drive wikipedia , lookup
Immunity-aware programming wikipedia , lookup
Stray voltage wikipedia , lookup
Earthing system wikipedia , lookup
Alternating current wikipedia , lookup
Power MOSFET wikipedia , lookup
Voltage regulator wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Buck converter wikipedia , lookup
Surge protector wikipedia , lookup
Voltage optimisation wikipedia , lookup
Switched-mode power supply wikipedia , lookup
BD9722FV Regulators System regulator for hard disk drive systems BD9722FV BD9722FV is a system regulator to convert into two systems of power supply from 5V. One is a synchronous rectification DC/DC controller. It enables to determine 1.0~3.3V output with external resistor and to provide power supply to a high current system. Another is a series power supply of an external NPN Tr drive type. It can be set up either 1.8V or 2.5V in a CTL terminal. !Applications HDD, PC !External dimensions (Unit : mm) 5.0 ± 0.2 16 9 1 8 1.15 ± 0.1 0.1 0.3Min. 6.4 ± 0.3 4.4 ± 0.2 !Features 1) High accurate Feed Back voltage (±2%). 2) Synchronous rectification. 3) Gate drives for external Nch MOSFET’s. 4) Short circuit protector with latch. 5) Under voltage lockout. 6) Soft start circuit. 7) Drives external NPN transistor for Vpp. 8) Variable switch of Vpp voltage (1.8V or 2.5V). 0.65 0.15 ± 0.1 0.1 0.22 ± 0.1 SSOP-B16 !Absolute maximum rating (Ta=25°C) Parameter Supply voltage1(Vcc−GND) Supply voltage2(PVcc1−SW) Supply voltage3(PVcc2−PGND) Supply voltage4(PVcc1−GND) Power dissipation Operating temperature range PVcc1−1 PVcc2 PVcc1−2 Pd Topr Limits −0.3 to +15 −0.3 to +7.5 −0.3 to +7.5 −0.3 to +15 450 ∗1 0 to +70 Unit V V V V mW °C Tstg −55 to + 125 °C Symbol VCC Storage temperature range ∗1:Reduced by 4.5 mW for each increase in Ta of 1 C over 25 C + + (when mounted on a board 50.0mm 50.0mm 1.6mm) !Recommended operating conditions (Ta=25°C) Parameter Supply voltage1(Vcc−GND) Supply voltage2(PVcc1−SW) Supply voltage3(PVcc2−PGND) Symbol Vcc MIN. 4.2 TYP. − MAX. 13.0 Unit PVcc1−1 4.2 6.5 V PVcc2 4.2 4.2 − − − − 6.5 13.0 V PVcc1−2 Supply voltage4(PVcc1−GND) 200 Output pin current Io − ∗In the case of boost−up of PVcc1, the voltage is approximately twice as much as PVcc2. V V mA 1/2 BD9722FV Regulators !Electrical characteristics (Unless otherwise noted. Ta=25°C, VCC=PVcc1=PVcc2=5V, CTL=GND) Conditions Iref=1mA CCT=150pF VINV=0.9V, CCT=150pF VCC Voltage CTL=GND Cgate=2000pF, PVCC 0.1 PVCC 0.9 2SC2411K, CTL Open/High 2SC2411K, CTL Low VppB=3.2V Unit V kHz % V V ns V V mA + MAX. 2.6 360 86 3.95 1.020 − 2.6 1.9 − + MIN. TYP. Parameter Symbol VREF 2.4 2.5 Output voltage FOSC 240 300 Oscillator frequency 80 83 DMAX Maximum duty cycle 3.65 3.8 VUT Threshold voltage Error amplifier reference voltage NON 0.980 1.000 Output rise/Fall time Tr/Tf 80 − Output voltage1 Vpp1 2.4 2.5 Vpp2 1.7 1.8 Output voltage2 VppB pin maximum current IvppB 12 20 ∗Designed Guarantee (Outgoing inspection is not done on all products.) !Block Diagram PVcc2 Vcc G1 225mV Vcc SW Vcc S Vcc R Vcc 2.2V 4.0V Vcc 5V U.V.L.O Vref PVcc2 11 A FB 3 Vcc Vref PVcc1 16 2 INV G1 15 Vref 3.3V SW 14 3A NON 1 U.V.L.O Delay Vcc 0.7V CT R1 PGND 13 A Vref Vcc 5V OSC 5 CCT G2 12 NON VppB 5V Vcc 9 8 Vpp 2.5V or 1.8V 10 B.G A U.V.L.O Vref Vref 6 Vref GND 7 Vref 4 CTL U.V.L.O 2.1V 0.8V Vcc 3.8V Hys=300mV 2/2 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document use silicon as a basic material. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.0