Download L16 - FMC Technologies

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Transcript
L16 Piston Pump Data
78 BHP Continuous Duty (105 BHP Intermittent Duty)
L16
Specifications
Standard Cast ISO Drawing
Performance Table
Pump Model
Piston
Diameter
(in) / (cm)
Displacement
(GAL/REV)
(LITERS/REV)
Pump Model
L16 (metric)
Configuration
Horizontal Triplex Piston
Number of Pistons
3
Stroke Length
4.0 Inches (10.16 cm)
Frame Load Rating
7,850 lbs (3,560.7 kg)
Pump Weight (Average)
705 lbs (319.78 kg)
Direction of Rotation
Top of pinion shaft away from
head
Internal Gear Ratio
3.94:1
Intermittent Duty Speed Rating
1,475 RPM
Continuous Duty Speed Rating
1,100 RPM
Ball Valve Max Speed Rating
900 RPM
Minimum Speed *
394 RPM
Mechanical Efficiency
85%
Lubrication System (Standard)
Splash, Gravity Return
Lube Oil Capacity
10 Quarts (37.8 Liters)
Lube Oil Type
SAE 80W90
Maximum Fluid Temperature
140 °F (250 °F Capability)
60°C (121°C Capacity)
Minimum Fluid Temperature
0 °F (-20 °F Capability)
-17.8°C (-28.91°C Capacity)
Standard Suction Size
STD - 2.50 Inch NPT
HV - 3.00 Inch NPT
Standard Discharge Size
STD - 1.25 Inch NPT
HV - 2.00 Inch NPT
Fluid End Material
Ductile Iron, Nickel Aluminum
Bronze
Valve Types
Disc Valves, Ball Valves, Abrasion
Resistant (AR) Valves
Hydraulic Motor Mount
SAE C - 2 Bolt with 1.25”-14T
SAE C - 4 Bolt with 1.25”-14T
* Slower RPM can be achieved with the addition of a pressurized lubrication system
Maximum
Pressure
(PSI) / (BAR)
Pump Capacity (GPM) / (Liters/Min) @ Input Speed (RPM)
394 RPM
750 RPM
900 RPM
1100 RPM
1475 RPM
L1614
1.750 / 4.445
0.0317 / 0.1200
2,500 / 172.37
12.5 / 47.32
23.8 / 90.09
28.5 / 107.88
34.9 / 132.11
46.8 / 177.16
L1616
2.000 / 5.08
0.0414 / 0.1567
2,500 / 172.37
16.3 / 61.70
31.1 / 117.73
37.3 / 141.20
45.6 / 172.61
61.1 / 231.29
L1618
2.250 / 5.715
0.0524 / 0.1984
2,000 / 137.90
10.7 / 40.50
39.3 / 148.77
47.2 / 178.67
57.7 / 218.42
77.3 / 292.61
L1622
2.750 / 6.985
0.0783 / 0.2964
1,300 / 89.63
30.9 / 116.97
58.7 / 222.20
70.5 / 266.87
86.1 / 325.92
115.5 / 437.22
* Horsepower based on 85 or 90% mechanical efficiency. Actual application horsepower requirements can be calculated using the equation:
BHP = (GPM * PSI) / (1714 * 0.85 or 0.90)
* Pump capacities shown are based on 100% volumetric efficiency.
* Dimensions shown are for general sizing purposes and should not be used for construction. Contact FMC for actual dimensions of pump ordered.
* FMC reserves the right to modify this information without prior notice.
STD = Standard Fluid Cylinder
HV = High Volume Fluid Cylinder
23
L16
Cast Pump Engineering Dimensional Outline
Standard Fluid End Shown
• FMC recommends NPSHa (available) exceeds NPSHr (required) by 5 feet of water.
• Take special consideration when calculating NPSHa. Recalculate NPSHa after pump model has been selected for more accurate values.
• NPSHr values are in feet of water. If you are pumping a different liquid than water, convert the required NPSH from water to the liquid
being pumped by dividing the published NPSHr value by the specific gravity of the liquid being pumped.
• FMC published NPSHr values are based on test data collected on specific pumps at the factory and are estimated values. Actual NPSHr
values for an ordered pump can only be determined by a factor test. For NPSH critical applications, contact the factory for additional
information and request an NPSHr test performed on your pump before shipment.
• Pump drawing dimensions in inches.
For additional information visit FMCPumps.com
Document related concepts
no text concepts found
Similar