Download Basic Electrical Testing

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Flexible electronics wikipedia , lookup

Power inverter wikipedia , lookup

Pulse-width modulation wikipedia , lookup

Fuse (electrical) wikipedia , lookup

Electromagnetic compatibility wikipedia , lookup

Power engineering wikipedia , lookup

Stepper motor wikipedia , lookup

Fault tolerance wikipedia , lookup

Immunity-aware programming wikipedia , lookup

Electrical ballast wikipedia , lookup

Islanding wikipedia , lookup

History of electric power transmission wikipedia , lookup

Variable-frequency drive wikipedia , lookup

Power electronics wikipedia , lookup

Single-wire earth return wikipedia , lookup

Three-phase electric power wikipedia , lookup

Ohm's law wikipedia , lookup

Rectifier wikipedia , lookup

Multimeter wikipedia , lookup

Current source wikipedia , lookup

Power MOSFET wikipedia , lookup

Portable appliance testing wikipedia , lookup

Schmitt trigger wikipedia , lookup

Resistive opto-isolator wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Metadyne wikipedia , lookup

Electrical substation wikipedia , lookup

Earthing system wikipedia , lookup

Voltage regulator wikipedia , lookup

Ground loop (electricity) wikipedia , lookup

Buck converter wikipedia , lookup

Opto-isolator wikipedia , lookup

Alternating current wikipedia , lookup

National Electrical Code wikipedia , lookup

Ground (electricity) wikipedia , lookup

Voltage optimisation wikipedia , lookup

Stray voltage wikipedia , lookup

Surge protector wikipedia , lookup

Mains electricity wikipedia , lookup

Electrical wiring in the United Kingdom wikipedia , lookup

Transcript
Basic Electrical Testing
Page 1 of 2
M. Corbin
Basic Electrical Testing
Servicing an electrical system does not have to be a nightmare even if the vehicle seems
haunted by amp imps and grounding gremlins. Testing is as easy as 1, 2, 3, and 4. For any circuit
to operate four items must be present: 1) voltage; 2) load; 3) ground; 4) continuity. All that is
needed for basic electrical testing is a DVOM (digital-volt-ohm-meter) and a wiring diagram.
Avoid the use of a test light as they can harm electronic circuits and are insufficient when
checking for available voltage.
12.66 v

V
1) Voltage: The standard rule for testing a circuit is to check the fuse(s) first. Verify
there is battery voltage at both ends of the fuse. But don’t stop there. Pull the fuse out and
visually check it. Even though its very rare, blade fuses have been known to break in the blade
instead of the fuse link. Sometimes it’s easier to go directly to the component that is not
functioning and check for the required voltage. If you unplug the component, the wire harness
will normally show supply voltage, however this proves nothing. The integrity of the voltage and
circuit must be tested under a load. So it is best to leave the component plugged in. If the test
shows proper voltage then everything in the circuit from the battery to the test point (i.e. fuse,
switch, relay, wiring, etc.) can be considered good and the problem is either a bad component or
ground. Should the DVOM show less than the required amount of voltage, a problem exists
between the battery and test point. A check of the wiring diagram will show what will have to be
tested next, such as a relay or switch.
12V
12V
+
NN334
Basic Electrical Testing
Page 2 of 2
Page 2
M. Corbin
2) Load: A load is a device that uses the voltage to do work such as a blower motor or
clutch coil. Testing of a load device usually means checking its resistance and/or its amperage
draw. These two tests will determine the quality of the component. A common procedure for
checking operation of these devices is to run jumper leads from the battery. This may allow the
unit to work but shows nothing of its ability to work within the specifications of its circuit. A
component that draws two or three amps above specification could cause several comebacks for
blown fuses or burnt relays and switches.
Motor
3) Ground: A commonly over looked portion of a circuit is its ground. A wire attached
to a ground point doesn’t mean there is a ground or that it is good; most circuit wiring problems
occur on the ground side. Using a test light from battery positive to the ground wire may allow
the light to glow but not allow the circuit to work properly. The ground side of any circuit should
be tested for resistance. One method is an ohms check of the ground, resistance should be zero.
A better method is to do a voltage drop test. With the circuit switched on, measure voltage from
the ground point of the load to the negative post of the battery. Maximum voltage reading is
normally below 200mv (.2v) for common electrical circuits such as those for blower motors,
compressor clutches etc. Computer circuits are normally less than 100mv (.100v) and in recent
years less than 60mv (.06v). Any readings higher than this indicates a poor ground and the need
for repair.
4) Continuity: No circuit will work unless there is a complete path from power, through
all relays and switches, to the load and finally to ground. Most continuity failures occur in
harness connectors and wire splices. Never assume that two wires plugged together are making
good contact. Disconnect them and visually inspect the terminals for burning, corrosion,
bent/broken leads or pushed back within the socket. Poor connections create high resistance that
use up circuit voltage to overcome them. This leaves the load device without enough voltage to
operate properly, if at all.
NN334