Download Xavi

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts
no text concepts found
Transcript
1
Design status of the Timepix2
pixel detector chip
X. Llopart
20th October 2010
International Workshop on Linear Colliders 2010
[email protected]
International Workshop on Linear Colliders 2010
2
Outline
• The Timepix chip
–
–
–
–
–
From Mpix2MXR20 to Timepix
Pixel schematic
Chip architecture
Timepix in TOA and TOT
Applications
• The Timepix2
–
–
–
–
Limitations of the Timepix chip
Scope & Main Requirements
A new pixel floorplan
Data push architecture
• Conclusions
[email protected]
International Workshop on Linear Colliders 2010
2
3
From Mpix2MXR20 to Timepix
• Design requested and funded by EUDet Collaboration
(http://www.eudet.org)
• Main features requested:
– Change counter function from particle counting to arrival time
measurement (clock tick counting) to provided depth dimension in
gas detectors
– Keep Timepix as similar as possible to Medipix2 series in order to
benefit from large prior effort in R/O hardware and software
• Features provided:
– Each pixel is programmable for either of:
• Particle counting
• Arrival time with a resolution up to 10ns
• Time over Threshold
[email protected]
International Workshop on Linear Colliders 2010
3
4
Timepix pixel schematic
•
•
•
Improved CSA gain by adding a cascode in the OTA
There is a single threshold with one 4-bit threshold adjustment DAC.
Each pixel can be configured independently in three different operation modes:
–
–
–
•
Arrival time mode
Energy mode (TOT)
Event counting
In acquisition mode there is a counting clock (Ref_Clk) distributed to the entire pixel matrix which is
synchronised with the discriminator output (HIT)
Previous Pixel
Ref_Clkb
Clk_Read
Mux
4 bits thr Adj
Mux
Input
CSA
Disc
Shutter
THR
Ctest
Testbit
P0
P1
Polarity
Timepix
Shutter_int
Synchronization
Logic
14 bits
Shift
Register
55μm
Mask
4
Conf
8-bits PCR
Test Input
OvControl
Ref_Clk
Analog
Digital
Clk_Read
Next Pixel
1
2
3
5
55μm
[email protected]
International Workshop on Linear Colliders 2010
4
5
Timepix chip architecture
–
–
–
As a time reference (up to 10ns)
As a energy counter
Digital Power (Ref_Clk=50MHz) → 220mW
•
256x256 55µm square pixels
•
Static Analog Power → 440mW
•
> 36M Transistors
3584-bit Pixel Column-255
In acquisition (Shutter On) an external clock is used:
3584-bit Pixel Column-1
•
Shutter precision of <5ns
Serial readout (@100MHz) → 9.17 ms
Parallel readout (@100MHz) → 287 µs
3584-bit Pixel Column-0
–
–
–
14080 m (pixel array)
Frame based readout architecture:
16120 m
•
256-bit Fast Shift Register
Bandgap + 13 DACs
LVDS
IO
In
Logic
LVDS
32-bit CMOS Output
Out
14111 m
[email protected]
International Workshop on Linear Colliders 2010
5
6
Timepix (2006)
Timepix design
requestedand funded by
EUDET collaboration
Time
over
Threshold
Time
of Arrival
sensor
Conventional Medipix2
counting mode remains.
Threshold
Threshold
Analogue
amplification
Digital
processing
Animation by
R.Plackett
Chip
read-out
Time
Time
of
Over
Arrival
Threshold
counts counts
to the end
to the
of
Addition of a clock up to
100MHz allows two new
modes.
Time over Threshold
Time of Arrival
Pixels can be individually
programmed into one of
these three modes
the
falling
Shutter
edge of the pulse
[email protected]
International Workshop on Linear Colliders 2010
6
7
Timepix in TOA and TOT
Time of Arrival
Time over Threshold
Strontium Source
Ion Beams at HIMAC
Charge deposition studies with various Isotopes
Space Dosimetry (Courtesy L. Pinsky, Univ. Houston)
[email protected]
International Workshop on Linear Colliders 2010
7
8
Timepix Applications
•
•
•
•
•
•
•
New Tracking Technologies
– LHCb Upgrade
– Linear Collider detectors
– Solid state Detector Development
TPC instrumentation
– EUDET
Emission Channeling Crystal Lattice Experiments
– ISOLDE
Image Intensifiers / Optical Photon Detectors
– Adaptive Optics
– Bioimaging
– LHCb RICH
ToF Mass Spectrometry
– Proteomic Imaging at AMOLF and Oxford
Imaging Mass Spec
– Functional Cellular Biology at Kiev
Photo Electron Emission Microscopy and Low Energy Electron Microscopy
– Neutron Monitoring at CNGS
– Space Dosimetry
– Education - CERN@School
[email protected]
International Workshop on Linear Colliders 2010
8
9
Limitations of the Timepix chip
• Chip architecture originally designed for imaging is used for
single (or sparse multiple) event readout
• Non triggerable
• Full frame readout only
– Serial readout (100 MHz): ~100 fps
– Parallel readout (100 MHz): ~3000 fps
• Either arrival time OR energy information OR particle counting
• Time-walk > 50ns
• Large periphery -> Non active area (~2000 µm)
[email protected]
International Workshop on Linear Colliders 2010
9
10
Timepix2 Scope
•
Several groups in the Medipix3 collaboration have shown interested in a new
version of the Timepix → Timepix2
•
Large range of applications (HEP and non-HEP):
–
–
–
–
X-ray radiography, X-ray polarimetry, low energy electron microscopy
Radiation and beam monitors, dosimetry
3D gas detectors, neutrons, fission products
Gas detector, Compton camera, gamma polarization camera, fast neutron camera, ion/MIP
telescope, nuclear fission, astrophysics
– Imaging in neutron activation analysis, gamma polarization imaging based on Compton effect
– Neutrino physics
– Particle Tracking – LHCb, LCD interest
•
•
•
Reuse many building blocks from Medipix3 chip (2009)
Timepix2 is an approved project by the Medipix3 collaboration with an
assigned budget (2-engineering runs) + partially funded by LHCb
Designed between CERN (CH), Nikhef (NL) and University of Bonn (DE)
[email protected]
International Workshop on Linear Colliders 2010
10
11
Timepix2 Main Requirements
• Lots of different applications → Very demanding specs !
Pixel size
55 µm x 55 µm
Pixel matrix array
256 x 256
Sparse readout
YES
PC, TOA or TOT recorded simultaneously
YES (2 at a time)
Minimum detectable charge
TOA resolution
≤ 500 e>1.5ns (25ns/16) 4bits (Gossipo3 style)
Peaking time
TOT resolution
Technology
Power consumption
< 25 ns
<5% channel to channel spread
IBM 130nm DM 3-2-3
<1.5W/cm2 (~45 μW/pixel) @1.2 V
Target floorplan
3 sides buttable and minimum periphery
TSVs possibility
YES. Multi-dicing scheme as Medipix3
[email protected]
International Workshop on Linear Colliders 2010
11
12
A new pixel floorplan
220 μm
145 μm
110 μm
72.5 μm
A
A
A
A
A
A
A
A
4x4
A
18.75 μm
[email protected]
A
A
27.5 μm
55 μm
55 μm
2x2
1x1
A
A
A
A
A
A
A
A
55 μm
A
A
18.75 μm
International Workshop on Linear Colliders 2010
12
13
Pros&Cons of super pixel architecture
• Advantages:
– Faster readout: Sparse readout, parallel bus on super pixel column,…
– Better isolation between digital and analog blocks
– Resources more efficiently shared:
• Analog: bias blocks, power supplies, …
• Digital: 1 clock tree per 4 pixel columns, 1 VCO (voltage controlled
oscillator per super pixel), …
– Possibility to use standard cells in the common digital block
– More compact end of column logic → Smaller periphery?
• Disadvantages:
– Routing of analog signal from the input pad to the preamplifier
– Different analog input capacitance if layout is not carefully done
– Some analog pads will not be shielded by the analog power planes
– Loss of uniformity in the analog side
[email protected]
International Workshop on Linear Colliders 2010
13
14
Parasitic layout extractions
•
•
•
A dummy layout has been done in order to evaluate the coupling between analog
and digital power supplies
In this design the top metal (MA) is used to route the analog signals on the top of
the digital side of the super-pixel to the analog section
E1 and LY are use to drive the power
and shielding
Pix<0>
Coupling line
Cap [fF]
Pix<0>
GND
0.4
Pix<0>
VDD
0.05
Pix<0>
VDDA
5.14
Pix<0>
GNDA
1.18
Pix<1>
GND
5.2
Pix<1>
VDD
2.7
Pix<1>
VDDA
1.3
Pix<1>
GNDA
0.68
[email protected]
Pix<1>
Total Cap [fF]
7.5
12
International Workshop on Linear Colliders 2010
14
15
Data push architecture
• The ‘ideal’ detector will read out all hits…
• An attempt to get close to this is the ‘Data Driven’ design
• Will push all events off the chip up to a limiting event rate
• Good for low rate and sparse applications
• Problematic for SLS physics or high rate imaging
• Cannot use the shutter to ‘squeeze down’ data rates
• Closer to ideal but not useable for all applications
• Requires significant on matrix logic and readout infrastructure
to achieve high data rates
[email protected]
International Workshop on Linear Colliders 2010
15
16
Timepix2 TLM overview
• T. Poikela (CERN) is setting up a highly configurable architectural model for
finding optimal readout architecture for Timepix2
• The goal is to have an executable functional specification of the chip
before detailed (Verilog) implementation starts
• Model can accept data from external files to simulate its performance in
different experiments and applications
• Can simulate architectures with different properties:
– continuous/triggered/full frame readout
– different super pixel configurations
– no super pixels
– shift register column readout architecture
– bus-based column readout architecture
– periphery w/ bus/shift register
[email protected]
International Workshop on Linear Colliders 2010
16
17
Simulation model (T.Poikela)
•
Simulation example:
–
–
–
–
–
–
Packet based readout
Centralized parallel arbitration (more optimistic than token
arbitration)
Ref. clock 40 MHz, (20 MHz col. readout clock)
Column bus 400 Mbps, EoC bus 3200 Mbps, Output 2560
Mbps
Double column architecture, 512 pixels per double column,
no super pixel functionality
Input frames: 500 to ~1200 hits per frame
2560 Mbps
[email protected]
512 pixels
per core
400 Mbps
per col
3200 Mbps
International Workshop on Linear Colliders 2010
17
18
Timepix testbeam run of 510 frames
[email protected]
International Workshop on Linear Colliders 2010
18
19
Simulated efficiency (T.Poikela)
99.6 % @110 kHz → 55 Mpixel_hit/s/cm2
[email protected]
International Workshop on Linear Colliders 2010
19
20
Conclusions
•
•
•
•
•
•
•
The Timepix2 chip, funded by the Medipix3 collaboration and partly by LHCb, will
be the successor of the Timepix chip
Designed in a commercial 130nm CMOS 8-metal process will reuse many building
blocks designed for Medipix3 (LVDS drivers, DACs, e-fuse, Test Pulse…)
The main requirements are:
– TOA and TOT simultaneously in each pixel with a TOA resolution > 1.5 ns
– Fast sparse readout
– 55 x 55 µm pixels…
The analog pixel architecture is well defined: Preamplifier + discriminator + 3 or 4
bits threshold equalization
The digital pixel architecture is not completely specified since different readout
topologies are being evaluated using a highly configurable Verilog architectural
model
Design is still at the specification level (dominated by the readout architecture)
Chip submission by the end of 2011
[email protected]
International Workshop on Linear Colliders 2010
20