Download Power Meter PM800

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Transcript
Power Meter PM800
Installation Manual
Retain for future use. /
Input/Output Module
PM8M2222, PM8M26, PM8M22
The addition of either symbol to a “Danger” or “Warning” safety label indicates that an
electrical hazard exists which will result in personal injury if the instructions are not
followed.
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
DANGER
DANGER indicates an immediately hazardous
situation which, if not avoided, will result in
death or serious injury.
WARNING
WARNING indicates a potentially hazardous
situation which, if not avoided, can result in
death or serious injury.
CAUTION
CAUTION indicates a potentially hazardous
situation which, if not avoided, can result in
minor or moderate injury.
CAUTION
CAUTION, used without the safety alert symbol,
indicates a potentially hazardous situation
which, if not avoided, can result in property
damage.
NOTE: Provides additional information to clarify or simplify a procedure.
PLEASE NOTE
Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. No
responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material.
CLASS A FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the interference at
his own expense. This Class A digital apparatus complies with Canadian ICES-003.
© 2004 Schneider Electric All Rights Reserved
1
ENGLISH
ENGLISH
Hazard Categories and Special Symbols
Read these instructions carefully and look at the equipment to become familiar with the device before trying to
install, operate, service, or maintain it. The following special messages may appear throughout this bulletin or
on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a
procedure.
63230-502-200A2
02/2004
ENGLISH
2
© 2004 Schneider Electric All Rights Reserved
63230-502-200A2
02/2004
PowerLogic® Power Meter Input/Output Module
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Supply Voltage Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
WIRING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
PM8M2222 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
PM8M26 Using the Internal 24 Vdc Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
PM8M26 Using an External Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
PM8M22 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D OUT (Digital Output) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D IN (Digital Input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A OUT (Analog Output) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A IN (Analog Input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Current Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Voltage Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
15
16
17
18
18
18
18
VIEWING I/O STATUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
LEDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
SPECIFICATIONS FOR PM8M2222 AND PM8M26 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
SPECIFICATIONS FOR PM8M22 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
© 2004 Schneider Electric All Rights Reserved
3
ENGLISH
TABLE OF CONTENTS
63230-502-200A2
02/2004
ENGLISH
4
© 2004 Schneider Electric All Rights Reserved
63230-502-200A2
02/2004
PowerLogic® Power Meter Input/Output Module
®
ENGLISH
PowerLogic Power Meter Input/Output Module
Introduction
The PowerLogic Power Meter Input/Output module (PM I/O) is available in three models. The
PM8M2222 is equipped with two digital outputs, two digital inputs, two analog outputs, and two
analog inputs. The PM8M26 module has two digital outputs, six digital inputs, and one 24 V source.
The PM8M22 has two digital outputs and two digital inputs.
I/O point connector
Power Meter Input/Output Module (PM I/O)
Identification
PM8M2222
R1-R2: 240V
MAX
30V MAX
2A CONT MAX
S1-S2: 150V
150V
MAX
MAX
48
Designed in USA
Diseñado en EE. UU.
Conçu aux États-Unis
C
Model number
US
LISTED 18X5
IND. CONT. EQ.
Assembled in Mexico
Ensamblado en México
Assemblé au Mexique
63230-502-05
© 2004 Schneider Electric All Rights Reserved
5
63230-502-200A2
02/2004
PowerLogic® Power Meter Input/Output Module
Safety
ENGLISH
DANGER
HAZARD OF ELECTRIC SHOCK, BURN, OR ARC FLASH
•
•
•
•
•
•
•
Apply appropriate personal protective equipment (PPE) and follow safe electrical work practices. See
NFPA 70E.
Only qualified workers should install this equipment. Such work should be performed only after reading
this entire set of instructions.
NEVER work alone.
Before performing visual inspections, tests, or maintenance on this equipment, disconnect all sources
of electric power. Assume that all circuits are live until they have been completely de-energized, tested,
and tagged. Pay particular attention to the design of the power system. Consider all sources of power,
including the possibility of backfeeding.
Turn off all power supplying the equipment in which the I/O is to be installed before installing and wiring
the I/O.
Always use a properly rated voltage sensing device to confirm that power is off.
The successful operation of this equipment depends upon proper handling, installation, and operation.
Neglecting fundamental installation requirements may lead to personal injury as well as damage to
electrical equipment or other property.
Failure to follow this instruction will result in death or serious injury.
Installation
Supply Voltage Considerations
The following table describes the possible combinations of PM I/O modules that can be installed
depending on control power voltage available.
Control Power Voltage Less than 208 V
Control Power Voltage Greater than 208 V
One PM8M22
One PM8M22
One PM8M26 and one PM8M22
One PM8M26 and one PM8M22
Two PM8M26’s
Two PM8M26’s
One PM8M2222
One PM8M2222 and one PM8M22
One PM8M2222 and one PM8M26
Two PM8M2222’s
6
© 2004 Schneider Electric All Rights Reserved
63230-502-200A2
02/2004
PowerLogic® Power Meter Input/Output Module
Mounting
ENGLISH
Refer to your power meter installation manual for minimum clearances and other guidelines for
mounting PM I/O modules.
A (attached directly
to the power meter)
B (attached to
another module)
0.70
(17.8 mm)
2.73
(69.4 mm)
0.78
(20 mm)
Dust cover
0.78
(20 mm)
3.56
(90.5 mm)
Two modules maximum.
3.56
(90.5 mm) When installing two
modules and one of them
is a PM8M22, the
PM8M22 must always be
in the “B” position. You
cannot install two
PM8M22 modules on the
same power meter.
1. Turn off all power to the power meter and the equipment in which it is installed:
a. Disconnect the metered voltage either by removing the fuses from the potential transformer
(PT secondaries) or by turning off the voltage disconnect switch.
b. Short circuit the current transformer (CT) secondaries.
c. Remove the control power and any power sources to the auxiliary inputs and outputs.
d. Always use a properly rated voltage sensing device to confirm that power is off.
NOTE: If the power meter is not installed yet, install it first. Refer to your power meter installation
manual. Before installing I/O modules, connect the phase current inputs. They will not be
accessible after mounting the I/O module.
© 2004 Schneider Electric All Rights Reserved
7
63230-502-200A2
02/2004
PowerLogic® Power Meter Input/Output Module
2. Follow the instructions that come with your anti-static or grounding strap to discharge static.
ENGLISH
NOTE: We recommend that you use an anti-static or grounding strap until you have completed
installation of the PM I/O.
3. Remove the dust cover from the PM8 or previously installed I/O module.
4. Hook one side of the PM I/O (1) and snap it in place as shown (2).
2
1
Wiring
1. Plug the connector into the PM I/O.
8
© 2004 Schneider Electric All Rights Reserved
63230-502-200A2
02/2004
PowerLogic® Power Meter Input/Output Module
mm2)
ENGLISH
2. Using 12- to 24-gauge (0.2–3.3
stranded wire, strip 0.25 in (6 mm) from the end of each
wire being connected to the terminal and insert the wire into appropriate hole of the connector.
3. Torque the wire binding screw 5–7 in-lb (0.56–.79 N•m).
PM8M2222
≤2A
I/O Module
~=
16
R1
Load
≤2A
15
~=
14
R2
13
S1
12
S2
11
S1, S2 Common
Load
≤ 100 mA
L (+) External Power Source
3 - 30 V --N (-) 6 - 240 V ~
L (+) External Power Source
3 - 30 V --N (-) 6 - 240 V ~
L (+)
~=
N (-)
10
External Power Source
20 - 150 V ~=
-
See
note 1.
9
8
Voltage source 0 - 5 V --- / current source 4 -20 mA.
+
See
note 1.
7
-
6
Voltage source 0 - 5 V --- / current source 4 -20 mA.
+
See note 3. Shield Landing
AO1 -
5
AI1 AI1 +
AI2 AI2 +
4
-
3
600Ω max.
+
AO2 -
2
-
AO2 +
1
AO1 +
See note 2.
600Ω max.
+
R = Relay Output
S = Status Input
AI = Analog Input
AO = Analog Output
= Normally open contact
= Normally closed contact
= Fuse
1. When in current mode, the input resistance is 250Ω. When in voltage mode,
the input resistance is 12.75 kΩ. Acceptable voltage range is 0 to 5 Vdc.
2. Open circuit voltage is 15 Vdc. When the analog output is used in voltage mode, the output will source 0 to 20 mA
of current. To convert this current to a voltage source, connect a 250Ω resistor across the output.
3. Grounding the shield is optional. If you want to ground the shield, you can use the shield landing terminal.
If you use the landing, you must connect earth ground to the shield landing with an auxiliary wire. The shield landing
is not connected internally. To prevent ground loops, we recommend that you only connect one side of the shield to ground.
© 2004 Schneider Electric All Rights Reserved
9
63230-502-200A2
02/2004
PowerLogic® Power Meter Input/Output Module
PM8M26 Using the Internal 24 Vdc Power Supply
ENGLISH
Module E/S
16
R1
R1 – commun
Charge
14
11
24 V
10
S1
9
S2
8
Terre commune 24 V S1, S2
7
S3
6
S4
5
S3, S4 communs
4
S5
3
S6
2
S5, S6 communs
1
24 V
+
-
Charge
12
R2 – commun
L (+) Alimentation externe
3 - 30 V --N (-) 6 - 240 V ~
~=
Charge
13
R2
≤2A
15
Charge
≤2A
L (+) Alimentation externe
3 - 30 V --N (-) 6 - 240 V ~
~=
REMARQUE : il est possible d'utiliser une seule
alimentation externe à la place des diverses
alimentations représentées.
= Contact normalement ouvert
= Contact normalement fermé
Les 24 volts peuvent alimenter au maximum
huit entrées logiques.
10
= Fusible
© 2004 Schneider Electric All Rights Reserved
63230-502-200A2
02/2004
PowerLogic® Power Meter Input/Output Module
ENGLISH
PM8M26 Using an External Power Supply
I/O Module
Load
16
R1
R1 – Common
14
L (+) External Power Source
3 - 30 V --N (-) 6 - 240 V ~
~=
Load
13
R2
≤2A
15
Load
≤2A
12
R2 – Common
11
24 V
10
S1
9
S2
8
S1, S2 24 V Ground Common
7
S3
6
S4
5
S3, S4 Common
4
S5
3
S6
2
S5, S6 Common
1
L (+) External Power Source
3 - 30 V --6 - 240 V ~
~=
Load
Not connected.
≤ 100 mA
N (-)
L (+)
~=
N (-)
≤ 100 mA
~=
L (+)
~=
≤ 100 mA
External Power Source
20 - 150 V
N (-)
External Power Source
20 - 150 V
~=
L (+)
~=
N (-)
External Power Source
20 - 150 V
~=
NOTE: A single external power source can be
used in place of the multiple power sources shown.
= Normally open contact
= Normally closed contact
= Fuse
© 2004 Schneider Electric All Rights Reserved
11
63230-502-200A2
02/2004
PowerLogic® Power Meter Input/Output Module
PM8M22
ENGLISH
I/O Module
Load
10
R1
R1 – Common
8
L (+) External Power Source
3 - 30 V --N (-) 6 - 240 V ~
~=
Load
Load
7
R2
≤2A
9
≤2A
6
R2 – Common
5
4
S1
3
S2
2
S1, S2 Ground Common
1
L (+) External Power Source
3 - 30 V --6 - 240 V ~
~=
Load
Not connected.
N (-)
≤ 100 mA
+
---
-
External Power Source
19 - 30 V ---
= Normally open contact
= Normally closed contact
= Fuse
12
© 2004 Schneider Electric All Rights Reserved
63230-502-200A2
02/2004
PowerLogic® Power Meter Input/Output Module
MAINT
SETUP
I/O
PM8M2222, PM8M26, and PM8M22
PM8M2222
1.
2.
3.
4.
5.
6.
D OUT
(Digital Out)
D IN
(Digital In)
A OUT
(Analog Out)
A IN
(Analog In)
ENGLISH
Setup
Scroll to MAINT.
Press MAINT.
Press Setup.
Enter your password.
Scroll to I/O.
Press I/O.
© 2004 Schneider Electric All Rights Reserved
13
63230-502-200A2
02/2004
PowerLogic® Power Meter Input/Output Module
ENGLISH
Setup screens for D OUT (digital output) and D IN (digital input) are available for all three types of I/O
module. Setup screens for A OUT (analog output) and A IN (analog input) are available on the
PM8M2222 module.
I/O SETUP
1;
D OUT
I/O SETUP
D IN
---:
1;
A OUT
A IN
---:
Scroll to access analog options for PM8M2222
(not displayed for other modules).
Input or output designation
Module position (A or B)
ANALOG IN B-AI 1
4 - 20
10
0
0
1;
<-
->
ANALOG IN B-AI 1
4 - 20
0.01
0
MAMP
MULT
LOWER
500
UPPER
EDIT
1;
<-
+
MAMP
MULT
LOWER
UPPER
OK
Scroll to access available input or output options.
14
© 2004 Schneider Electric All Rights Reserved
63230-502-200A2
02/2004
PowerLogic® Power Meter Input/Output Module
ENGLISH
Refer to your power meter installation and reference guides for operating instructions and
explanations of the available setup options.
D OUT (Digital Output)
RELAY A-R1
NORM
EXT
1;
<-
->
EDIT
Digital outputs can be controlled internally with the alarm or externally with SMS or PLC.
To assign or remove alarm capability for a digital output:
1. From the D OUT screen, scroll to the output you want to edit.
RELAY A-R1
NORM
ALARM
1;
<-
+
Select ALARM.
OK
2. Select ALARM and press OK.
© 2004 Schneider Electric All Rights Reserved
15
PowerLogic® Power Meter Input/Output Module
63230-502-200A2
02/2004
3. Press +.
ENGLISH
OVER 1A
**
1;
AL-01
<-
->
**
Asterisks display to indicate that the digital
output has alarm capability. They do not
display if you remove the capability.
+
4. Save changes.
D IN (Digital Input)
DIGITAL IN A-S1
NORM
1;
•
•
•
16
<-
->
EDIT
Normal = simple ON/OFF digital inputs with timestamping. The periodic rate is less than 2 Hz with
a pulse duration > 10 ms.
Demand Interval Synch Pulse = accepts a demand synch pulse from a utility demand meter.
Conditional Energy Control: you can configure one digital input to control conditional energy.
© 2004 Schneider Electric All Rights Reserved
63230-502-200A2
02/2004
Input metering (not available on the PM8M22): used for ON/OFF digital inputs with a periodic rate
between 2 and 25 Hz with a 50% duty cycle. No timestamping is provided for input metering
mode.
NOTE: When in input metering mode, you cannot enable a digital alarm for the digital input.
A OUT (Analog Output)
ANALOG OUT B-AO1
4 - 20
0
0
0
1;
•
•
•
<-
->
MAMP
Mode. See “Mode” on page 18.
REG.
LOWER
UPPER
EDIT
“0–5 VOLT” or “4–20 MAMP” = type of signal to be measured (V or mA).
REGIS = Register assigned to to the analog output.
LOWER and UPPER = range of user defined values an attached power meter will report.
© 2004 Schneider Electric All Rights Reserved
17
ENGLISH
•
PowerLogic® Power Meter Input/Output Module
63230-502-200A2
02/2004
PowerLogic® Power Meter Input/Output Module
A IN (Analog Input)
ENGLISH
ANALOG OUT B-AO1
4 - 20
0
0
0
1;
•
•
•
<-
->
MAMP
Mode. See “Mode”.
REG.
LOWER
UPPER
EDIT
“0–5 VOLT” or “4–20 MAMP” = type of signal to be measured (V or mA).
MULTI = Multiplier used in calculating data displayed: 0.001, 0.01, 0.1, 1, 10, 100, 1000
LOWER and UPPER = range of user defined values an attached power meter will report.
Mode
Current Mode
•
•
•
•
Output signal is “4–20 MAMP.”
REGIS = register assigned to to the analog output.
LOWER = user defined value when current equals 4 mA.
UPPER = user defined value when current equals 20 mA.
Voltage Mode
•
•
•
•
18
Output signal is “0–5 VOLT.”
REGIS = register assigned to to the analog output.
LOWER = user defined value when voltage equals 0 Volts.
UPPER = user defined value when voltage equals 5 Volts.
© 2004 Schneider Electric All Rights Reserved
63230-502-200A2
02/2004
PowerLogic® Power Meter Input/Output Module
Number of transitions since the last reset of the counter.
DIGITAL INPUTS
0
5
5
1;
<-
}}}}}}}}}}
10
50
SI
100
Empty bar graph = OFF
Full bar graph = ON
{{{{{{{{{{
10
50
100
A-S1
}}}}}}}}}}
10
50
100
A-S2
->
This displays a number between the user defined upper
and lower limit values proportional to the input or output.
ANALOG OUTPUTS
0.00
4.00
1;
<-
}}}}}}}}}}
10
50
100
B-AO1
The bar graph is a visual representation of the
percentage of the user defined full scale reading.
{{{{{}}}}}
10
50
100
B-AO2
->
© 2004 Schneider Electric All Rights Reserved
19
ENGLISH
Viewing I/O Status
63230-502-200A2
02/2004
PowerLogic® Power Meter Input/Output Module
LEDs
ENGLISH
(On bottom
edge of
module)
PM8M2222
LED flashes green
to indicate the unit
is operating.
(PM8M26 and
PM8M2222).
2
S
1
2
R
1
Digital input LEDs (S 1, 2, etc.) are
red when inputs are active (ON).
Relay output LEDs (R 1, 2, etc.) are
red when outputs are active (ON).
Troubleshooting
DANGER
HAZARD OF ELECTRIC SHOCK, BURN, OR ARC FLASH
•
•
This equipment must be installed and serviced only by qualified personnel.
Qualified persons performing diagnostics or troubleshooting that require electrical conductors to be
energized must comply with NFPA 70 E – Standard for Electrical Safety Requirements for Employee
Workplaces and OSHA Standards – 29 CFR Part 1910 Subpart S – Electrical.
Failure to follow this instruction will result in death or serious injury.
Problem
Solution
Timestamping does not work.
Check to see if set for input metering mode. See “D OUT (Digital Output)” on
page 15.
Module resets.
Check external power connections.
Ensure that control power voltage is adequate for modules installed. See
“Supply Voltage Considerations” on page 6.
0–5 V output seems
inaccurate.
Ensure that the total load resistance is 250Ω. Meter resistance can affect
load resistance.
Analog input that is set to 4–20 The input current is less than 3.6 mA. Check for open connection to analog
displays –32767.
input and check quality of current source.
20
© 2004 Schneider Electric All Rights Reserved
63230-502-200A2
02/2004
PowerLogic® Power Meter Input/Output Module
ENGLISH
Specifications For PM8M2222 and PM8M26
Environmental
Operating Temperature
–25°C to +70°C
Storage Temperature
–40°C to +85°C
Humidity Rating
5–95% (relative humidity, non-condensing: at 40°C)
Altitude Range
0–3000 meters
For Indoor Use Only
—
Pollution Degree 2
—
Installation Category II
Digital Inputs AC/DC for 2222 and 26
Input Voltage Range
20–150 Vac/dc
Input Current Draw (Maximum) 2 mA
Turn on Time (Max.)
1 msec
Turn off Time (Max.)
1 msec
Turn on voltage
20 V
Turn off voltage
5V
Maximum input frequency
25 Hz 50% duty cycle (20 msec ON, 20 msec OFF)
Digital Output AC/DC Ratings for 2222 and 26
Load Voltage Range
0 to 240 Vac, 0 to 30 Vdc
Load Current
2 A rms, 5 A peak for 10 s once every hour
Maximum output frequency
1 Hz 50% duty cycle (500 msec on, 500 msec off)
Expected mechanical life
15 million operations
Contact ratings
250,000 operations at 2 A 250 Vac
Analog Inputs for 2222
Input voltage/current range
0–5 Vdc or 4-20 mA user selectable
Accuracy
0.2% full scale
Maximum input voltage
5.1 Vdc
Temperature drift
50 ppm/°C typical
© 2004 Schneider Electric All Rights Reserved
21
63230-502-200A2
02/2004
PowerLogic® Power Meter Input/Output Module
Specifications For PM8M2222 and PM8M26
ENGLISH
Analog Output Ratings for 2222
Output Current Range
4-20 mA (20 mA into 600 ohms max.)
Accuracy
1% full scale
Temperature drift
50 ppm/°C typical
Open circuit voltage
15 V
Standards
Product
US
UL508
Canada
cUL508
EU
IEC61010-1
Emissions
Radiated
FCC part 15 Class A, EN55011
Conducted
FCC part 15 Class A, EN55011
Harmonics
IEC 1000-3-2
Flicker
IEC 1000-3-3
Immunity
ESD
IEC 1000-4-2 Level 3
Radiated
IEC 1000-4-3 Level 3
EFT
IEC 1000-4-4 Level 3
Surges
IEC 1000-4-5 Level 3
Conducted
IEC 1000-4-6 Level 3
Mag. Field
IEC 1000-4-8 Level 3
Voltage Dips
IEC 1000-4-11
Internal 24 V Power Source (PM8M26 only)
22
Output voltage
20–34 Vdc
Output current
10 mA max.
Maximum load
8 digital inputs
© 2004 Schneider Electric All Rights Reserved
63230-502-200A2
02/2004
PowerLogic® Power Meter Input/Output Module
ENGLISH
Specifications For PM8M22
Environmental
Operating Temperature
–25°C to +70°C
Storage Temperature
–40°C to +85°C
Humidity Rating
5–95% (relative humidity, non-condensing: at 40°C)
Altitude Range
0–3000 meters
For Indoor Use Only
—
Pollution Degree 2
—
Installation Category II
Digital Inputs AC/DC
Input Voltage Range
19–30 Vdc
Input Current Draw (Maximum) 5 mA @ 24 Vdc
Turn ON Time (Max.)
500 msec
Turn OFF Time (Max.)
500 msec
Turn ON voltage
19 Vdc
Turn OFF voltage
3 Vdc
Maximum input frequency
1 Hz 50% duty cycle (500 msec on, 500 msec off)
Digital Output AC/DC Ratings
Load Voltage Range
3 to 240 Vac, 3 to 30 Vdc
Load Current
2 A rms 5 A peak for 10 s once every hour
Maximum output frequency
1 Hz 50% duty cycle (500 msec on, 500 msec off)
Expected mechanical life
15 million operations
Contact ratings
250,000 operations at 2 A 250 Vac
Standards
Product
US
UL508
Canada
cUL508
EU
IEC61010-1
© 2004 Schneider Electric All Rights Reserved
23
63230-502-200A2
02/2004
PowerLogic® Power Meter Input/Output Module
Specifications For PM8M22
ENGLISH
Emissions
Radiated
FCC part 15 Class A, EN55011
Conducted
FCC part 15 Class A, EN55011
Harmonics
IEC 1000-3-2
Flicker
IEC 1000-3-3
Immunity
24
ESD
IEC 1000-4-2 Level 3
Radiated
IEC 1000-4-3 Level 3
EFT
IEC 1000-4-4 Level 3
Surges
IEC 1000-4-5 Level 3
Conducted
IEC 1000-4-6 Level 3
Magnetic Field
IEC 1000-4-8 Level 3
Voltage Dips
IEC 1000-4-11
© 2004 Schneider Electric All Rights Reserved
Módulo de entrada/salida de la Central de Medida
Manual de instrucciones
Schneider Electric
Power Management Operations
295 Tech Park Drive, Suite 100
LaVergne, TN 37086
Tel: +1 (615) 287-3500
www.powerlogic.com
This product must be installed, connected, and used in
compliance with prevailing standards and/or installation
regulations.
As standards, specifications, and designs change from time to
time, please ask for confirmation of the information given in this
publication.
Ce produit doit être installé, raccordé et utilisé
conformément aux normes et/ou aux règlements
d’installation en vigueur.
En raison de l’évolution des normes et du matériel, les
caractéristiques et cotes d’encombrement données ne
nous engagent qu’après confirmation par nos services.
Este producto deberá instalarse, conectarse y utilizarse en
conformidad con las normas y/o los reglamentos de
instalación vigentes.
Debido a la evolución constante de las normas y del material,
es recomendable solicitar previamente confirmación de las
características y dimensiones.
Editado por: Square D Company PMO
Producción: Square D Company PMO
63230-502-200A2
02/2004 © 2004 Schneider Electric Reservados todos
los derechos