Download HD40P(X) Fixed Lens Indoor Minidome Camera

Package Includes:
WARNINGS AND CAUTIONS
FCC Compliance Statement
Installation and servicing should be performed only by qualified
and experienced personnel to conform to all local codes and to
maintain your warranty.
Information to the User: This equipment has been tested and found
WARNING!
This device is configured for 12 V DC operation
only, do NOT connect to higher voltage. Use
only with NRTL approved 12 V DC power
supplies. To prevent potential ground loop
issues a separate PSU should be used for each
to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
camera. A multiple output PSU may be used if
the multiple output PSU has isolated and
protected (2 A Max) outputs.
CAUTION: Changes or modifications not expressly approved by
the party responsible for compliance could void the
user’s authority to operate the equipment.
Manufacturer’s Declaration of Conformance
WARNING!
12 V DC models require the use of CSA
Certified/UL Listed Class 2 power adapters to
ensure compliance with electrical safety
standards.
The manufacturer declares that the equipment supplied with
this guide is compliant with the essential requirements of the
EMC Directive 2004/108/EC and the General Product Safety
Directive (GPSD) 2001/95/EC, conforming to the requirements
of standards EN 55022 for emissions, EN 50130-4 for
immunity, and EN 60065 for Electrical Equipment safety.
Need Help?
Call 1.800.323.4576 for sales, service and customer support.
www.honeywellvideo.com
Dome Camera
Guide Pattern
Ø85
HD40P(X)
Fixed Lens Indoor Minidome Camera
Mounting Screw
Operation
Manual
User Guide
Specifications:
Specification
Signal System
Scanning System
Scanning Frequency (H)
Scanning Frequency (V)
Image Sensor
Effective Pixels (H × V)
S/N Ratio
Resolution
Video Output Level
Lens
Focus
Sync. System
Min. Illumination(F1.2, 30IRE, AGC Max.)
Electronic Shutter
White Balance
AGC, BLC
Input/Output Connector
Power Consumption
Dome Size (Ø)
Weight
HD40P(X)
Description
NTSC/PAL
2:1 interlace
15.734 kHz (NTSC) / 15.625 (PAL)
59.94 Hz (NTSC) / 50 Hz (PAL)
1/3″ interline transfer CCD
510 × 492 (NTSC) / 512 × 582 (PAL)
50 dB or more (AGC off)
420 TV Lines
1.0 Vp-p (75 ohms, composite)
Fixed lens (f=3.8 mm)
Manual
Internal
0.1 lux (color)
1/60–120,000 s (NTSC) / 1/50–120,000 s (PAL)
Auto (AWB)
Auto (AGC)
Power (red jack), video (yellow jack)
12 V DC (±10%) / 180mA
3.35″ (85 mm)
Approx. 0.46 Ib ( 0.210 kg)
• 1/3″ interline transfer CCD
• 420 TVL
• Built-in fixed lens (f=3.8 mm)
• Min. illumination (F1.4, 50 IRE, AGC Max.):
0.1 lux (color)
• Auto White Balance
• AGC
• Diameter of bubble: 3.35″ (85 mm)
• Easy installation (3-axis)
Thank you for purchasing a Honeywell HD40P(X) fixed lens indoor minidome
camera. Before installing your camera, please carefully read this guide and
verify your model:
• HD40P, 420 TVL, 3.8 mm, 12 V DC, NTSC camera
• HD40PX, 420 TVL, 3.8 mm, 12 V DC, PAL camera
Document 800-01622V1−Rev A−10/2012
#1
Video (Yellow)
Video Output
Power - 12 V DC
#2 (Yellow)
• Read and keep these instructions.
• Please ensure that your installation area can safely support the
weight of the camera.
• Do not install the camera in extreme temperature conditions.
Only use the camera where temperatures are within the limits
shown in the specifications section of the user guide. Be
especially careful to provide ventilation when operating under
high temperatures.
• Do not aim the camera towards an extreme light source to
prevent damaging the CCD.
• This camera is rated for indoor operation; do not expose this
camera to rain or moisture.
• Do not touch the camera lens, dome or bezel (front glass
plate).
• Do not drop the camera or subject it to physical shock.
• Do not use a strong or abrasive detergent when cleaning the
camera.
1
2
3
4
Attach the template to the
wall or ceiling.
Drill two holes according to
the template, then insert the
anchors into the drilled holes.
Pull out the power/video
cables, and connect.
Use the supplied screws to
secure the camera to the
mounting surface.
5
Adjust the field of view and
focus by turning the 3D axis
camera bracket by hand.
6
Place the dome cover over
the base, then secure.
Insert a coin in
the side hole, then
twist, to remove
the dome cover.
• The wire is polarized.
• Use 12 V DC power source.
No.
GND
IMPORTANT SAFETY INSTRUCTIONS
DIMENSIONS
CABLE CONNECTIONS
This manual explains how to install and operate your camera.
Before installing, ensure that you are familiar with this product’s
special features and proper operating technique.
Terminal Color
Description
#1 Video Output
Function
Yellow
1.0 Vp-p
#2 Power Input
Red
12 V DC (±10%)
3.35″
(85 mm)
ADJUSTING THE FIELD OF VIEW
90°
Tilt
Dome
Base
Nothing appears
on the screen.
• Check that the power cord and the video
cable between the camera and monitor are
properly connected.
• Check that you have properly connected the
Video cable to the camera video output jack.
The image on the
screen is dim.
• If the lens is obstructed (for example, with
dirt), clean the lens with a soft, clean cloth.
If the camera is exposed to too strong light,
change the camera position.
• Adjust the lens' focus properly.
The image on the
screen is dark.
• Adjust the contrast feature of the monitor.
If you loop through an intermediate device,
set the termination (75 ohms / Hi-Z) properly.
• Check the supply voltage.
360°
Horizontal
360°
Dome
Cover
3.35″
(85 mm)
If you have trouble operating your camera, please see the following
recommendations. Please contact an authorized technician if you
need further help.
Template
Mounting
Screw
8″
0.1 )
2- mm
(4.5
TROUBLESHOOTING
The 3D camera gimbal makes it easy
to rotate in any direction.
Ceiling
4.45″
(113 mm)
3.02″
(76.7 mm)
THIS SYMBOL INDICATES THAT
IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS
ACCOMPANY THIS UNIT.
INSTALLATION
1.34″
(34 mm)
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE THE COVER.
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
THIS SYMBOL INDICATES THAT
DANGEROUS VOLTAGE
CONSTITUTING A RISK OF
ELECTRIC SHOCK IS PRESENT
WITHIN THE UNIT.
1.68″
(42.7 mm)
CAUTION
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
Pan