Download Evaluation Board User Guide UG-119

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Flip-flop (electronics) wikipedia , lookup

Printed circuit board wikipedia , lookup

Public address system wikipedia , lookup

Buck converter wikipedia , lookup

Analog-to-digital converter wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Phone connector (audio) wikipedia , lookup

Opto-isolator wikipedia , lookup

Transcript
Evaluation Board User Guide
UG-119
One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
ADAU1361 Evaluation Board
PACKAGE CONTENTS
GENERAL DESCRIPTION
ADAU1361 evaluation board
USBi control interface board
USB cable
Evaluation board documentation/quick-start guide
This user guide explains the design and setup of the ADAU1361
evaluation board.
The EVAL-ADAU1361Z includes both single-ended and differential stereo line-level analog audio inputs as well as a digital
audio interface. Single-ended and differential analog outputs are
also provided, as well as a stereo capless headphone output.
SUPPORTING DOCUMENTATION
ADAU1361 data sheet
AN-1056 Application Note, Capless Headphone Virtual Ground
Short-Circuit Protection for the ADAU1361 and ADAU1761
AN-1006 Application Note, Using the EVAL-ADUSB2EBZ
AN-1007 Application Note, Using the ADAU1761 in DSP
Bypass Mode to Emulate an ADAU1361
SigmaStudio Help (included in software installation)
The USBi provides power and the I2C communications interface to
the evaluation board. A switch allows the ADAU1361 to operate at
either 3.3 V or 1.8 V. The SigmaStudio™ programming software is
used for all register controls and SigmaDSP® core programming.
A header is included for interfacing to stereo digital microphones.
EVALUATION BOARD BLOCK DIAGRAM
I2C COMMUNICATIONS
INTERFACE (USBi)
POWER
SUPPLY
DIGITAL
MIC
INPUTS
ANALOG
AUDIO
INPUTS
ANALOG
AUDIO
OUTPUTS
08957-001
ADAU1361
Figure 1.
www.BDTIC.com/ADI
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS.
Rev. 0 | Page 1 of 12
UG-119
Evaluation Board User Guide
TABLE OF CONTENTS
Package Contents .............................................................................. 1
Using the Evaluation Board .............................................................5
Supporting Documentation ............................................................ 1
ADAU1361 Low-Power Codec ...................................................5
General Description ......................................................................... 1
Power...............................................................................................5
Evaluation Board Block Diagram ................................................... 1
Analog Audio Input ......................................................................5
Revision History ............................................................................... 2
Analog Audio Output ...................................................................5
Setting Up the Evaluation Board—Quick Start ............................ 3
Clocking the Evaluation Board ...................................................6
SigmaStudio Software Installation ............................................. 3
External Digital Audio Header ....................................................6
Hardware Setup, USBi.................................................................. 3
Digital Microphone and Jack Detection Input ..........................6
Powering the Board ...................................................................... 3
I2C Communications Header ......................................................6
Connecting Audio Cables ........................................................... 3
Evaluation Board Schematics and Artwork ...................................7
Switch and Jumper Settings......................................................... 3
Ordering Information .................................................................... 10
Setting Up the Registers in SigmaStudio ................................... 4
Bill of Materials ........................................................................... 10
REVISION HISTORY
3/10—Revision 0: Initial Version
www.BDTIC.com/ADI
Rev. 0 | Page 2 of 12
Evaluation Board User Guide
UG-119
SETTING UP THE EVALUATION BOARD—QUICK START
SigmaStudio SOFTWARE INSTALLATION
SWITCH AND JUMPER SETTINGS
To install the SigmaStudio software, follow these steps:
To configure the board for stereo analog input and output, make
sure that the switches and jumpers are set as follows (see Figure 2).
1.
2.
3.
Open the provided .zip file and extract the files to your PC.
Alternately, insert the SigmaStudio CD into the PC optical
drive and locate the SigmaStudio folder on the CD.
If Microsoft® .NET Framework Version 2.0 is not already
installed on the PC, install it by double-clicking dotnetfx.exe.
Install SigmaStudio by double-clicking setup.exe and
following the prompts. A computer restart is not required.
HARDWARE SETUP, USBi
To set up the USBi hardware, follow these steps:
1.
2.
3.
Plug the USBi ribbon cable into Header J1.
Connect the USB cable to your computer and to the USBi.
When prompted for drivers, follow these steps:
a)
b)
c)
d)
e)
f)
g)
•
•
•
•
•
•
•
The ADAU1361 uses the on-board oscillator as a master
clock source (S5 switched to OSC).
Regulator output VDD is set for 3.3 V operation
(S1 switched to 3.3 V).
Power is supplied by USB (J5 is connected with a jumper).
AVDD is connected to VDD (J17 connected).
IOVDD and AVDD operate at VDD (J16 connected).
DAC_SDATA and ADC_SDATA are tied together to loopback data from ADC to DAC (jumper across two bottom
right pins of J6).
I2C control mode is hardwired on board.
Choose Install from a list or a specific location.
Choose Search for the best driver in these locations.
Check the box for Include this location in the search.
The USBi driver is located in C:\Program Files\
Analog Devices Inc\Sigma Studio\USB drivers.
Click Next.
If prompted to choose a driver, select CyUSB.sys.
If the PC is running Windows® XP and you receive the
message that the software has not passed Windows
Logo testing, click Continue Anyway.
POWERING THE BOARD
The board can be powered either by the USBi or by an external
power supply. For the board to run independently from the
computer, disconnect Jumper J5 and connect the power supply
at J2. The power indicator LED D1 should now be lit.
CONNECTING AUDIO CABLES
In this example, the board is set up for stereo analog inputs and
stereo analog outputs, using 3.5 mm (1/8”) cables.
Connect the audio source to Input Jack J24.
Connect Output Jack J19 to your headphones.
08957-002
1.
2.
Figure 2. Evaluation Board Setup and Configuration
www.BDTIC.com/ADI
Rev. 0 | Page 3 of 12
UG-119
Evaluation Board User Guide
1.
SETTING UP THE REGISTERS IN SigmaStudio
This section details how to pass an audio signal from the ADC
inputs to the DAC outputs using the headphone drivers. The
codec is configured with SigmaStudio.
3.
2.
Start playing the audio source; you should hear audio on the
outputs.
Your screen should now resemble Figure 3.
08957-004
2.
Create a new project. The Hardware Configuration
tab opens.
Drag an ADAU1361 cell and a USBi cell into the blank
work area.
Connect the USBi cell to the ADAU1361 cell by clicking
and dragging from the top blue output pin of the USBi cell
to the green input pin of the ADAU1361 cell.
This locks the PLL and sets up the registers for proper
routing of the record and playback paths. If the PLL has
successfully locked, then the box under PLL Lock Bit
should turn from red to green.
Figure 4. Hardware Configuration Tab—Register Setup
08957-003
1.
In the IC1-ADAU1361 Register Controls tab, select the 3
and 4 in Capless HP Out option from the Automatic
Startup list and click Load Preset (see Figure 4).
Figure 3. Hardware Configuration Tab
www.BDTIC.com/ADI
Rev. 0 | Page 4 of 12
Evaluation Board User Guide
UG-119
USING THE EVALUATION BOARD
ADAU1361 LOW-POWER CODEC
The ADAU1361 is a low power, stereo audio codec that
supports stereo 48 kHz record and playback at 14 mW from a
1.8 V analog supply. The stereo audio ADCs and DACs support
sample rates from 8 kHz to 96 kHz as well as a digital volume
control.
The SigmaStudio graphical development tool is used to configure
the ADAU1361. SigmaStudio’s outputs can be used to easily
integrate the ADAU1361 in a system.
The record path includes an integrated microphone bias circuit
and six inputs. The inputs can be mixed and muxed before the
ADC, or they can be configured to bypass the ADC. The
ADAU1361 includes a stereo digital microphone input.
The ADAU1361 includes five high power output drivers (two
differential and three single-ended) that support stereo headphones, an earpiece, or other output transducers. AC-coupled
or capless configurations are supported. Individual fine level
controls are supported on all analog outputs. The output mixer
stage allows for flexible routing of audio.
L1 and C24 are connected to the AVDD pin of the ADAU1361
and function as an L-C filter to reject high frequency power
supply noise common in GSM mobile applications. This filter
is tuned to approximately 1.5 GHz.
ANALOG AUDIO INPUT
The EVAL-ADAU1361Z has three ac-coupled 1/8” input jacks:
two mono differential jacks and one stereo single-ended jack.
The tips of the differential input jacks, J20 and J22 (labeled IN 1
and IN 2), are connected to the negative input of the ADAU1361,
and the rings are connected to the positive input. The stereo
single-ended input on J24 (labeled IN 3) is connected to the
LAUX and RAUX inputs of the ADAU1361. IN 1 and IN 2 can
also be configured to bias a microphone. This is enabled by
connecting the MICBIAS pin of the ADAU1361 to the tip of the
input connectors with Jumper J15 and Jumper J18.
At VDD = 3.3 V, the full-scale analog input level of the EVALADAU1361Z is 1.0 V rms (1.0 V rms on the single-ended
inputs and 0.5 V rms on each of the two pins of the differential
inputs). The full-scale input level scales with VDD.
POWER
ANALOG AUDIO OUTPUT
The evaluation board uses the ADP3336 low dropout voltage
regulator to generate either 3.3 V or 1.8 V for the board. The
output voltage VDD of the ADP3336 is set with external resistors
that can be switched with S1 to select either 3.3 V or 1.8 V
outputs (see Table 1).
The EVAL-ADAU1361Z has four 1/8” output jacks: two
mono differential, one stereo single-ended, and one stereo
capless headphone output. The differential outputs on J21
and J25 (labeled DIFF OUT L and DIFF OUT R, respectively,
are biased at AVDD/2 V. The tips of the differential output jacks
are connected to the positive output of the ADAU1361, and the
rings are connected to the negative outputs. J23 is a stereo,
single-ended, ac-coupled output.
Table 1. VDD Voltage Settings
Voltage Regulator Output (V)
3.3
1.8
S1 Setting
Up
Down
At VDD = 3.3 V, the full-scale analog output level of the
EVAL-ADAU1361Z is 1.0 V rms (1.0 V rms on the single-ended
outputs and 0.5 V rms on each of the two pins of the differential
outputs). The differential line outputs of the ADAU1361 can
each be boosted by 6 dB to 2.0 V rms. The full-scale output level
scales with VDD.
The maximum operating current draw from this board is
approximately 75 mA. This maximum value is reached with
VDD = 3.3 V, headphone outputs enabled, and all LEDs
enabled.
Typically, the regulator input comes from the USBi 5 V dc USB
supply on Header J1. This supply is enabled with a jumper on
J5. To use another 5 V dc supply source, remove the jumper
on J5 and connect the other supply either on the J2 power jack
(positive tip) or via soldering leads from a supply such as a
battery to J3. On J3, Pin 1 (square pad) is ground, and Pin 2
(circle pad) is the power connection.
When the ADP3336 is outputting a regulated voltage, LED D1
is illuminated red.
VDD is connected to the AVDD pin of the ADAU1361 with
Jumper J17. To connect the ADAU1361 IOVDD pin to the same
supply, connect J16, also. These headers can also be used to
separate the supplies of the ADAU1361 from the rest of the
board and to connect an external supply to the ADAU1361.
Note that Jack J21 and Jack J25 tie the ring to the sleeve, resulting
in a floating ground output. Be aware of this when connecting
to these outputs.
Table 2. Analog and Digital Audio Connectors
Jack
J4
J6
J19
J20
J21
J22
J23
J24
J25
Function
Stereo digital microphone input
Serial data port input/output
Capless headphone output
Left differential input
Left differential output
Right differential input
Stereo single-ended line output
Stereo single-ended line input
Right differential output
www.BDTIC.com/ADI
Rev. 0 | Page 5 of 12
UG-119
Evaluation Board User Guide
CLOCKING THE EVALUATION BOARD
Table 3. Master Clock Source Settings
Clock Source
Do Not Use—Function Disabled on USBi
MCLK from Header J6
On-Board 12.288 MHz Clock Oscillator (U3)
S5 Setting
Up
Middle
Down
J7
J8
08957-006
The EVAL-ADAU1361Z requires a master clock to operate. The
source of this clock is set by Switch S5 (see Table 3).
Figure 6. Jumper Settings (J7 and J8) for Jack Detection (Low Signal Detected)
EXTERNAL DIGITAL AUDIO HEADER
Figure 7. Jumper Settings (J7 and J8) for Jack Detection (High Signal Detected)
DIGITAL MICROPHONE AND JACK DETECTION
INPUT
I2C COMMUNICATIONS HEADER
A pair of digital microphones can be connected to the evaluation board on Header J4. The pin connections for J4 are
detailed on the evaluation board silkscreen.
J8
The I2C communications header, J1, provides an interface to the
ADAU1361 communications port. This header connects to the
USBi board (EVAL-ADUSB2), which controls communication
between the evaluation board and SigmaStudio on the PC.
Additionally, a DSP reset line and USB bus power line are
provided. The SigmaStudio hardware configuration for this
setup is shown in Figure 8.
08957-005
J7
J8
08957-008
J7 and J8 set up the routing of signals to the JACKDET/MICIN
pin of the ADAU1361. These jumper settings are shown in
Figure 5, Figure 6, and Figure 7; they are also shown on the PCB
silkscreen. Toggling the jack detection signal can be simulated
by setting up the jack detect function on the ADAU1361 and
then inserting and removing Jumper J8 with J7-B (lower
connection) connected.
J7
08957-007
The LRCLK, BCLK, ADC_SDATA, and DAC_SDATA pins of
the ADAU1361 can be connected to external devices with the
5 × 2 header, J6. The pins on the top row of J6 are connected to
ground; the pins on the bottom row are the signals indicated on
the silkscreen.
Figure 5. Jumper Settings (J7 and J8) for Stereo Digital Microphone Input
Figure 8. Using the EVAL-ADAU1361Z and the USBi with SigmaStudio
www.BDTIC.com/ADI
Rev. 0 | Page 6 of 12
www.BDTIC.com/ADI
J24
Figure 9. Board Schematics, Page 1
C2
1kΩ
R27
1kΩ
R24
0Ω
R16
0Ω
C12
0.10µF
R20
0Ω
R8 0.10µF
0Ω
R11
C3
OPEN
C25
OPEN
C27
OPEN
C13
OPEN
C19
OPEN
C6
OPEN
49.9kΩ RESISTORS ON INPUTS REFERENCE AC COUPLING
CAPACITORS TO GROUND PREVENTING POPS WHEN
'HOT-PLUGGING' INPUTS. NOT NECESSARY FOR
HARDWIRED DESIGN.
2kΩ
R15
MIC_BIAS
DIFFERENTIAL INPUT 2
STEREO SINGLE-ENDED INPUT
J22
J20
2kΩ
R7
MIC_BIAS
J15
J18
R12
R9
SCL
SDA
RINN
LINP
LINN
C22
RHP 19
LOUTN 17
LOUTP 18
16
ROUTN
ROUTP 15
MONOOUT 21
LHP 20
0.10µF
L1
OE 1
3
49.9Ω OUTPUT U3
2 GND
R47
EXT_MCLK
2
7
12.288MHZ
4 VDD
CM
BCLK 28
10kΩ
R46
C39
0.10µF
C18
0.10µF
BCLK
6
8
5
7
1
S5-B
C21
10µF
DAC_SDATA
LRCLK
ADC_SDATA
L2
2
R5
R3
OPEN
R13
OPEN
R29
OPEN
R18
10kΩ
100Ω
R19
R22
10kΩ
100Ω
R23
R2
OPEN
0Ω
IOVDD
IOVDD
VDD
R26
OPEN
10µF
C17
10µF
C23
R14
OPEN
OPEN
0Ω
R10
C4
+
OPEN
0Ω
C1
R6 +
R4
OPEN
CAPLESS
HEADPHONE OUTPUT
BOARD IS SHIPPED IN CAPLESS MODE.
TO CONVERT TO AC-COUPLED,
REMOVE 0Ω RESISTORS FROM R5, R6, AND R10;
ADD 220µF CAPACITORS TO C1 AND C4 AND 0Ω RESISTOR TO R4.
DAC_SDATA 27
LRCLK 29
2
C24
9.1PF
26
3
4
C16
0.10µF
1
1.2nH
VDD
C14
10µF
ADC_SDATA
USB_CLK
MCLK
ADDR0/CLATCH
SCL/CCLK
SDA/COUT
ADDR1/CDATA
JACKDET/MICIN
U1
ADAU1361
1
2
3
32
31
30
4
RINP
6 LAUX
14
RAUX
12
13
10
11
C10
0.10µF
DVDD
TP5
S5-A
JACKDET/MICIN
MIC_BIAS
C31
0.10µF
IOVDD
J17
AVDD 8
10µF
C8
10µF
C11
MICBIAS 5
DIFFERENTIAL INPUT 1
49.9kΩ
49.9kΩ
49.9kΩ
10µF
C7
10µF
C5
10µF
C20
10µF
C15
10µF
C26
IOVDD 1
25 DGND
R21
R17
R25
R28
49.9kΩ
49.9kΩ
49.9kΩ
Rev. 0 | Page 7 of 12
10µF
C28
24
DVDDOUT
J16
23
AVDD
AGND
22
AGND
9
TP3
MONO DIFFERENTIAL OUTPUT RIGHT
J25
J23
STEREO SINGLE-ENDED OUTPUT
J21
MONO DIFFERENTIAL OUTPUT LEFT
J19
Evaluation Board User Guide
UG-119
EVALUATION BOARD SCHEMATICS AND ARTWORK
08957-009
www.BDTIC.com/ADI
Rev. 0 | Page 8 of 12
2
3
1
RAPC722X
J2
Figure 10. Board Schematics, Page 2
OPEN
K
BRD_RESET
A
D4
+5V SUPPLY FROM USBi
BATTERY INPUT
+5V
J3
C34
0.10µF
R32
10kΩ
C32
10µF
TP2
C33
0.10µF
4
1
2
3
5
TP1 TP4
U2
ADP3336
7 IN
OUT
8 IN
OUT
6 SD
OUT
GND FB
J4
12
10
8
6
4
2
TP6
R33
147kΩ
10kΩ
R37
VDD
169kΩ
R34
140kΩ
R35
C35
10nF
J5
SPDT
R39
M2
3V3
C36
0.10µF
C37
10µF
VDD
POLARIZING PLUG 100Ω
JUMPER2SIP3
J7
A B
IOVDD
RED DIFFUSED
D1
100Ω
C29
0.10µF
C30
0.10µF
SCL
SDA
C40
0.10µF
1
3
5
7
9
R31
10kΩ
C41
0.10µF
J6
2x5
9
7
5
3
1
SERIAL DATA INTERFACE
10
8
6
4
2
+5V
J1 USB_CLK
2
4
6
8
10 BRD_RESET
HEADER_10WAY_POL
R30
10kΩ
IOVDD
CONTROL PORT INTERFACE
LRCLK
BCLK
DAC_SDATA
ADC_SDATA
49.9Ω
R38
PLANE DECOUPLING
EXT_MCLK
BCLK
JACKDET/MICIN
R48
J8
R1
10kΩ
S1 1V8
DIGITAL MICROPHONE INPUT
SOCKET_12WAY_UNSHROUD
10kΩ
11
9
7
5
3
1
DVDD = +1.8V (SHOWN) OR +3.3 V SUPPLY
M1
POLARIZING PLUG
R36
RIGHT DMIC
LEFT DMIC
JACK DETECT SIGNAL
C38
0.10µF
UG-119
Evaluation Board User Guide
08957-010
UG-119
08957-011
Evaluation Board User Guide
Figure 11. Board Silkscreen and Parts Placement
www.BDTIC.com/ADI
Rev. 0 | Page 9 of 12
UG-119
Evaluation Board User Guide
ORDERING INFORMATION
BILL OF MATERIALS
Table 4.
Qty
2
12
6
14
1
4
1
1
1
1
1
1
1
6
1
1
7
1
1
4
7
7
2
6
9
2
1
1
1
2
1
1
6
1
1
1
Designator
C1, C4
C2, C10, C12, C16, C18,
C22, C31, C33, C34, C36,
C38, C39
C3, C6, C13, C19, C25, C27
C5, C7, C8, C11, C14,
C15, C17, C20, C21, C23,
C26, C28, C32, C37
C24
C29, C30, C40, C41
C35
D1
D4
J1
J2
J3
J4
J5, J8, J15 to J18
J6
J7
J19 to J25
L1
L2
R1, R19, R23, R48
R2 to R4, R13, R14,
R26, R29
R5, R6, R8, R10, R11,
R16, R20
R7, R15
R9, R12, R17, R21,
R25, R28
R18, R22, R30 to R32,
R36, R37, R39, R46
R24, R27
R33
R34
R35
R38, R47
S1
S5
TP1 to TP6
U1
U2
U3
Description
Capacitor (open)
Capacitor, multilayer ceramic, 0.10 μF, 50 V, X7R, 0603
Manufacturer
Part Number
Panasonic
ECJ-1VB1H104K
Capacitor (open)
Capacitor, multilayer ceramic, 10 μF, 10 V, X7R, 0805
Murata
GRM21BR71A106KE51L
Capacitor, multilayer ceramic, 9.1 pF, 50 V, NP0, 0603
Capacitor, multilayer ceramic, 0.10 μF, 16 V, X7R, 0402
Capacitor, multilayer ceramic, 10 nF, 25 V, NP0, 0603
LED, red diffused, 6 millicandela, 635 nm, 1206
Schottky diode, 30 V, 0.5 A, SOD-123
Header, 10-way (2 × 5), shrouded, polarized
Mini power jack, 0.08”, R/A T/H
Open
Header, 12-way (2 × 6), socket, unshrouded
Header, 2-pin, unshrouded, 2-jumper, 0.10”
(use Tyco shunt, 881545-2)
Header, 10-way (2 × 5), unshrouded
Header, 3-position, SIP
Stereo mini jack, SMT
Inductor, 1.2 nH
Chip ferrite bead, 600 Ω @ 100 MHz
Chip resistor, 100 Ω, 1%, 100 mW, thick film, 0603
Resistor, open
Murata
Panasonic
TDK
Lumex
ON Semiconductor
3M
Switchcraft, Inc.
GQM1885C1H9R1CB01D
ECJ-0EX1C104K
C1608C0G1E103J
SML-LX1206IW-TR
MBR0530T1G
N2510-6002RB
RAPC722X
Sullins Connector Solutions
Sullins Connector Solutions
PPPC062LFBN-RC
PBC02SAAN
Sullins Connector Solutions
Sullins Connector Solutions
CUI Inc.
Jaro Components, Inc.
TDK
Panasonic
PBC05DAAN
PBC03SAAN
SJ-3523-SMT
HFI-160808-1N2S
MPZ1608S601A
ERJ-3EKF1000V
Chip resistor, 0 Ω, 5%, 100 mW, thick film, 0603
Panasonic
ERJ-3GEY0R00V
Chip resistor, 2 kΩ, 1%, 100 mW, thick film, 0603
Chip resistor, 49.9 kΩ, 1%, 100 mW, thick film, 0603
Panasonic
Panasonic
ERJ-3EKF2001V
ERJ-3EKF4992V
Chip resistor, 10 kΩ, 1%, 100 mW, thick film, 0603
Panasonic
ERJ-3EKF1002V
Chip resistor, 1 kΩ, 1%, 100 mW, thick film, 0603
Chip resistor, 147 kΩ, 1%, 100 mW, thick film, 0603
Chip resistor, 169 kΩ, 1%, 100 mW, thick film, 0603
Chip resistor, 140 kΩ, 1%, 100 mW, thick film, 0603
Chip resistor, 49.9 Ω, 1%, 100 mW, thick film, 0603
Slide switch, SPDT, PC mount, L = 2 mm
Slide switch, DP3T, PC mount, L = 4 mm
Mini test point, white, 0.1” OD
SigmaDSP codec
Adjustable low dropout voltage regulator
SMD oscillator, 12.288 MHz, fixed, 1.8 VDC to 3.3 VDC
Panasonic
Panasonic
Panasonic
Panasonic
Panasonic
E-Switch
E-Switch
Keystone Electronics
Analog Devices
Analog Devices
Abracon Corporation
ERJ-3EKF1001V
ERJ-3EKF1473V
ERJ-3EKF1693V
ERJ-3EKF1403V
ERJ-3EKF49R9V
EG1271
EG2305
5002
ADAU1361BCPZ
ADP3336ARMZ
AP3S-12.288MHz-F-J-B
www.BDTIC.com/ADI
Rev. 0 | Page 10 of 12
Evaluation Board User Guide
UG-119
NOTES
www.BDTIC.com/ADI
Rev. 0 | Page 11 of 12
UG-119
Evaluation Board User Guide
NOTES
I2C refers to a communications protocol originally developed by Philips Semiconductors (now NXP Semiconductors).
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions
set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you
have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.
(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,
temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided
for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional
limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term
“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including
ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may
not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to
promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any
occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.
Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice
to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO
WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED
TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL
PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF
THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE
AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable
United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of
Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby
submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
©2010 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
UG08957-0-3/10(0)
www.BDTIC.com/ADI
Rev. 0 | Page 12 of 12