Download LM2902DT

General-purpose Operational Amplifiers / Comparators
SIGNATURE SERIES
Operational Amplifiers
LM358DT/PT/ST/WDT/WPT,LM2904DT/PT/ST/WDT/WPT
LM324DT/PT/WDT,LM2902DT/PT/WDT
●Description
The Universal Standard family LM358 / 324, LM2904 /
2902 monolithic ICs integrate two independent
op-amps and phase compensation capacitors on a
single chip
and feature high-gain, low power consumption, and
an operating voltage range of 3[V] to 32[V]
(single power supply.)
No.11094EBT05
SIGNATURE
SERIES
Dual
LM358 family
LM358DT
LM358PT
LM358ST
LM358WDT
LM358WPT
Quad
LM2902 family
LM324 family
LM2904 family
LM2904DT
LM2904PT
LM2904ST
LM2904WDT
LM2904WPT
LM324DT
LM324PT
LM324WDT
LM2902DT
LM2902PT
LM2902WDT
●Features
1) Operating temperature range
0[℃] to + 70[℃]
Commercial Grade
LM358/324 family
:
Extended Industrial Grade
LM2904/2902 family : -40[℃] to +125[℃]
2) Wide operating supply voltage
+3[V] to +32[V] (single supply)
±1.5[V] to ±16[V] (dual supply)
3) Low supply current
4) Common-mode input voltage range including ground
5) Differential input voltage range equal to maximum rated supply voltage
6) High large signal voltage gain
7) Wide output voltage range
●Pin Assignment
OUTPUT 1
OUTPUT 1
INVERTING
INPUT 1
1
2
NON-INVERTING
INPUT 1
3
Vcc－
4
SO package8
LM358DT
LM358WDT
LM2904DT
LM2904WDT
8 Vcc
＋
INVERTING
INPUT 1
NON-INVERTING
INPUT 1
7 OUTPUT 2
－ ＋
＋ －
6
NON-INVERTING
LM358PT
LM358WPT
LM2904PT
LM2904WPT
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
2
14
－
＋
＋
－
3
Vcc＋ 4
INVERTING
INPUT 2
5 INPUT 2
TSSOP8
1
NON-INVERTING
INPUT 2
INVERTING
INPUT 2
OUTPUT 2
11 Vcc
5
－
＋
6
7
SO package14
Mini SO8
LM358ST
LM2904ST
LM324DT
LM324WDT
LM2902DT
LM2902WDT
1/17
OUTPUT 4
INVERTING
13
INPUT 4
NON-INVERTING
12
INPUT 4
＋
－
－
NON-INVERTING
10
INPUT 3
INVERTING
9
INPUT 3
8
OUTPUT 3
TSSOP14
LM324PT
LM2902PT
2011.06 - Rev.B
LM358DT/PT/ST/WDT/WPT,LM2904DT/PT/ST/WDT/WPT
LM324DT/PT/WDT,LM2902DT/PT/WDT
Technical Note
●Absolute Maximum Ratings (Ta=25[℃])
Parameter
Symbol
Supply Voltage
VDD
Operating Temperature Range
Topr
Rating
LM358 family
LM324 family
LM2904 family
LM2902 family
+32
Unit
V
0 to +70
℃
-40 to +125
Storage Temperature Range
Tstg
-65 to +150
℃
Input Common-mode Voltage
VICM
-0.3 to +32
V
Maximum Junction Temperature
Tjmax
+150
℃
●Electric Characteristics
○LM358,LM324 family(Unless otherwise specified, Vcc+=+5[V], Vcc-=0[V])
Limit
Parameter
Temperature
Symbol
range
Input Offset Voltage (*1)
VIO
Input Offset Current (*1)
IIO
Input Bias Current (*1)
IIB
LM358 family
LM324 family
Min.
Typ.
Max.
Min.
Typ.
Max.
25℃
－
2
7
－
－
7
Full range
－
－
9
－
－
9
25℃
－
2
30
－
2
30
Full range
－
－
－
－
－
100
25℃
－
20
150
－
20
150
Full range
－
－
200
－
－
300
Unit
Conditions
Fig.
No
mV
VO=1.4[V],RS=0[Ω]
5[V]< Vcc+<30[V]
0<VIC< Vcc+-1.5[V]
98
nA
VO=1.4[V]
98
nA
VO=1.4[V]
98
+
Large Signal Voltage Gain
AVD
Supply Voltage Rejection Ratio
SVR
Supply Current (All Amp)
ICC
Input Common-mode Voltage Range
VICM
Common-mode Rejection Ratio
CMR
Output Short Circuit Current (*2)
Output Sink Current (*2)
25℃
25
100
25℃
65
100
Full range
65
－
－
－
25
100
－
65
110
－
－
65
－
－
Vcc =15[V]
V/mV VO=1.4[V] to 11.4[V]
RL=2[kΩ]
dB
25℃
－
－
－
－
0.7
1.2
Vcc =5[V],No Load
25℃
－
－
－
－
1.5
3
Vcc+=30[V],No Load
Full range
－
0.7
1.2
－
0.8
3
Full range
－
－
2
－
1.5
3
25℃
－
－
Vcc -1.5
+
－
－
Vcc -1.5
Full range
－
－
Vcc -2.0
+
－
－
Vcc -2.0
mA
Vcc =30[V],No Load
+
V
Vcc+=30[V]
98
dB
RS≦10[kΩ]
98
Vcc+=15[V],VO=+2[V]
VID=+1[V]
99
VO=+2[V],
Vcc+=15[V],VID=-1[V]
VO=+0.2[V],
Vcc+=15[V] ,VID=-1[V]
99
V
RL=2[kΩ]
99
V
Vcc+=30[V],RL=10[kΩ]
99
RL=10[kΩ]
99
70
85
－
70
80
－
－
－
60
－
－
Isource
25℃
20
40
60
20
40
70
mA
10
20
－
10
20
－
mA
Isink
25℃
12
50
－
12
50
－
μA
VOH
Low Level Output Voltage
VOL
Slew Rate
99
+
60
High Level Output Voltage
Vcc+=5[V],No Load
+
25℃
Vopp
98
+
Full range
Output Voltage Swing
RS≦10[kΩ]
Vcc+=5[V] to 30[V]
98
25℃
0
－
Vcc+-1.5
－
－
－
Full range
0
－
Vcc+-2.0
－
－
－
25℃
27
28
－
27
28
－
Full range
27
－
－
27
－
－
25℃
－
5
20
－
5
20
Full range
－
－
20
－
－
20
SR
25℃
－
0.6
－
－
0.4
－
Gain Bandwidth Product
GBP
25℃
－
1.1
－
－
1.3
－
Total Harmonic Distortion
THD
25℃
－
0.02
－
－
0.015
－
en
25℃
－
55
－
－
40
－
nV/ Hz
Input Offset Voltage Drift
DVIO
－
－
7
－
－
7
－
μV/℃
－
－
Input Offset Current Drift
DIIO
－
－
10
－
－
10
－
pA/℃
－
－
VO1/VO2
25℃
－
120
－
－
120
－
dB
Input Equivalent Noise Voltage
Channel Separation
mV
RL=2[kΩ],CL=100[pF],
Vcc+=15[V]
VI=0.5[V] to 3[V],
Unity Gain
Vcc+=30[V],RL=2[kΩ],
MHz CL=100[pF]
VIN=10[mV],f=100[kHz]
f=1[kHz],AV=20[dB]
％
RL=2[kΩ]
CL=100[pF],VO=2[Vpp]
V/μs
f=1[kHz],RS=100[Ω]
Vcc+=30[V]
1[kHz]≦f≦20[kHz]
99
99
99
99
99
(*1) Absolute value
(*2) Under high temperatures, please consider the power dissipation when selecting the output current.
When output terminal is continuously shorted the output current reduces the internal temperature by flushing.
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
2/17
2011.06 - Rev.B
LM358DT/PT/ST/WDT/WPT,LM2904DT/PT/ST/WDT/WPT
LM324DT/PT/WDT,LM2902DT/PT/WDT
Technical Note
○LM2904,LM2902 family(Unless otherwise specified, Vcc+=+5[V], Vcc-=0[V])
Limit
Parameter
Symbol
Temperature
range
LM2904 family
Min.
Input Offset Voltage (*3)
VIO
Input Offset Current (*3)
IIO
Input Bias Current (*3)
IIB
Large Signal Voltage Gain
AVD
Supply Voltage Rejection Ratio
SVR
Supply Current (All Amp)
Input Common-mode Voltage Range
ICC
VICM
Common-mode Rejection Ratio
CMR
Output Short Circuit Current (*4)
Isource
Typ.
LM2902 family
Max.
Min.
Typ.
Unit
Conditions
Fig.
No
Max.
25℃
－
2
7
－
2
7
Full range
－
－
9
－
－
9
25℃
－
2
50
－
2
30
Full range
－
－
200
－
－
200
25℃
－
20
150
－
20
150
Full range
－
－
200
－
－
300
25℃
25
100
－
25
100
－
mV
VO=1.4[V]
98
nA
VO=1.4[V]
98
nA
VO=1.4[V]
98
Vcc+=15[V]
V/mV VO=1.4[V] to 11.4[V]
RL=2[kΩ]
25℃
65
100
－
65
110
－
Full range
65
－
－
65
－
－
25℃
－
0.7
1.2
－
0.7
1.2
25℃
－
－
－
－
1.5
3
Full range
－
－
2
－
0.8
1.2
Vcc+=5[V],No Lord
Full range
－
－
－
－
1.5
3
Vcc+=30[V],No Lord
+
+
25℃
－
－
Vcc -1.5
－
－
Vcc -1.5
Full range
－
－
Vcc+-2.0
－
－
Vcc+-2.0
25℃
70
85
－
70
80
－
Full range
60
－
－
60
－
－
25℃
20
40
60
20
40
70
dB
RS≦10[kΩ]
98
99
Vcc+=5[V],No Lord
mA
Vcc+=30[V],No Lord
99
V
Vcc+=30[V]
98
dB
RS=10[kΩ]
98
mA
Vcc+=+15[V],VO=+2[V]
VID=+1[V]
98
+
Output Sink Current (*4)
Isink
Output Voltage Swing
Vopp
High Level Output Voltage
VOH
Low Level Output Voltage
VOL
10
20
－
10
20
－
mA
12
50
－
12
50
－
μA
25℃
0
－
Vcc+-1.5
－
－
－
Full range
0
－
Vcc+-2.0
－
－
－
25℃
27
－
－
27
28
－
Full range
27
28
27
－
－
25℃
－
V
V
VO=2[V],Vcc =+5[V]
VID=-1[V]
VO=+0.2[V],
Vcc+=+15[V] ,VID=-1[V]
99
RL=2[kΩ]
99
Vcc+=30[V],RL=10[kΩ]
Vcc+=30[V],RL=10[kΩ]
99
25℃
－
5
20
－
5
20
Full range
－
－
20
－
－
20
SR
25℃
－
0.6
－
－
0.4
－
Gain Bandwidth Product
GBP
25℃
－
1.1
－
－
1.3
－
Total Harmonic Distortion
THD
25℃
－
0.02
－
－
0.015
－
en
25℃
－
－
－
－
40
－
nV/ Hz
Input Offset Voltage Drift
DVIO
－
－
7
－
－
7
－
μV/℃
-
－
Input Offset Current Drift
DIIO
－
－
10
－
－
10
－
pA/℃
-
－
VO1/VO2
25℃
－
120
－
－
120
－
dB
Slew Rate
Input Equivalent Noise Voltage
Channel Separation
mV
RL=10[kΩ]
99
RL=2[kΩ],CL=100[pF],
Unity Gain
VI=0.5[V] to 3[V]
Vcc+=1.5[V]
Vcc+=30[V],RL=2[kΩ]
MHz CL=100[pF]
VIN=10[mV]
f=1[kHz],AV=20[dB]
RL=2[kΩ]
％
CL=100[pF],
Vcc+=30[V],VO=2[Vpp]
V/μs
f=1[kHz],RS=100[Ω]
Vcc+=30[V]
1[kHz]≦f≦20[kHz]
99
99
99
99
99
(*3) Absolute value
(*4) Under high temperatures, please consider the power dissipation when selecting the output current.
When the output terminal is continuously shorted the output current reduces the internal temperature by flushing.
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
3/17
2011.06 - Rev.B
LM358DT/PT/ST/WDT/WPT,LM2904DT/PT/ST/WDT/WPT
LM324DT/PT/WDT,LM2902DT/PT/WDT
Technical Note
●Reference Data LM358 family
LM358 family
POWER DISSIPATION Pd [mW]
800
LM358 family
LM358 family
LM358PT
LM358WPT
LM358ST
600
25℃
LM358DT
LM358WDT
32V
0℃
400
200
5V
70℃
3V
0
70
0
25
50
75
100
AMBIENT TEMPERATURE : [℃]
Ta [℃]
Fig. 1
Derating Curve
Fig. 2
Supply Current – Supply Voltage
LM358 family
Fig. 3
Supply Current – Ambient Temperature
LM358 family
LM358 family
0℃
0℃
25℃
70℃
25℃
70℃
Fig. 4
Maximum Output Voltage – Supply Voltage
(RL=10[kΩ])
Fig. 5
Maximum Output Voltage – Ambient Temperature
(VCC=5[V],RL=2[kΩ])
Fig. 6
Output Source Current – Output Voltage
(VCC=5[V])
LM358 family
LM358 family
LM358 family
15V
70℃
3V
5V
0℃
3V
5V
15V
25℃
Fig. 7
Output Source Current – Ambient Temperature
(VOUT=0[V])
Fig. 8
Output Sink Current – Output Voltage
(VCC=5[V])
Fig. 9
Output Sink Current – Ambient Temperature
(VOUT=VCC)
LM358 family
LM358 family
LM358 family
32V
25℃
0℃
0℃
5V
25℃
3V
70℃
70℃
Fig. 10
Low Level Sink Current - Supply Voltage
(VOUT=0.2[V])
Fig. 11
Low Level Sink Current - Ambient Temperature
(VOUT=0.2[V])
Fig. 12
Input Offset Voltage - Supply Voltage
(Vicm=0[V], VOUT=1.4[V])
(*)The data above is ability value of sample, it is not guaranteed.
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
4/17
2011.06 - Rev.B
LM358DT/PT/ST/WDT/WPT,LM2904DT/PT/ST/WDT/WPT
LM324DT/PT/WDT,LM2902DT/PT/WDT
Technical Note
●Reference Data LM358 family
LM358 family
LM358 family
LM358 family
3V
5V
32V
25℃
0℃
32V
3V
5V
70℃
Fig. 13
Input Offset Voltage – Ambient Temperature
(Vicm=0[V], VOUT=1.4[V])
Fig. 14
Input Bias Current – Supply Voltage
(Vicm=0[V], VOUT=1.4[V])
Fig. 15
Input Bias Current – Ambient Temperature
(Vicm=0[V],VOUT=1.4[V])
LM358 family
LM358 family
LM358 family
70℃
0℃
25℃
0℃
25℃
70℃
[V]
Fig. 16
Input Bias Current – Ambient Temperature
(VCC=30[V],Vicm=28[V],VOUT=1.4[V])
Fig. 17
Input Offset Voltage – Common Mode Input Voltage
(VCC=5[V])
Fig. 18
Input Offset Current – Supply Voltage
(Vicm=0[V],VOUT=1.4[V])
LM358 family
LM358 family
LM358 family
0℃
15V
25℃
3V
5V
5V
32V
70℃
Fig. 19
Input Offset Current
– Ambient Temperature
(Vicm=0[V],VOUT=1.4[V])
Fig. 20
Large Signal Voltage Gain
– Supply Voltage
(RL=2[kΩ])
LM358 family
LM358 family
36V
0℃
Fig. 21
Large Signal Voltage Gain
– Ambient Temperature
(RL=2[kΩ])
LM358 family
32V
25℃
70℃
Fig. 22
Common Mode Rejection Ratio
– Supply Voltage
5V
3V
Fig. 23
Common Mode Rejection Ratio
– Ambient Temperature
Fig. 24
Power Supply Rejection Ratio
– Ambient Temperature
(*)The data above is ability value of sample, it is not guaranteed.
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
5/17
2011.06 - Rev.B
LM358DT/PT/ST/WDT/WPT,LM2904DT/PT/ST/WDT/WPT
LM324DT/PT/WDT,LM2902DT/PT/WDT
Technical Note
●Reference Data LM324 family
LM324family
family
BA2904
LM324 family
family
BA2904
LM324 family
1000
POWER DISSIPATION Pd [mW]
LM324ST
LM324DT
LM324WDT
800
32V
25℃
600
0℃
400
5V
200
70℃
3V
0
0
25
70
50
75
100
AMBIENT TEMPERATURE :[℃]
Ta [℃]
Fig. 25
Derating Curve
Fig. 26
Supply Current – Supply Voltage
LM324 family
Fig. 27
Supply Current – Ambient Temperature
LM324 family
LM324 family
0℃
0℃
25℃
70℃
25℃
70℃
Fig. 28
Maximum Output Voltage – Supply Voltage
(RL=10[kΩ])
Fig. 29
Fig. 30
Maximum Output Voltage – Ambient Temperature Output Source Current – Output Voltage
(VCC=5[V],RL=2[kΩ])
(VCC=5[V])
LM324 family
LM324 family
LM324 family
15V
70℃
3V
5V
0℃
5V
15V
3V
25℃
Fig. 31
Output Source Current – Ambient Temperature
(VOUT=0[V])
Fig. 32
Output Sink Current – Output Voltage
(VCC=5[V])
Fig. 33
Output Sink Current – Ambient Temperature
(VOUT=VCC)
LM324 family
LM324 family
LM324 family
32V
0℃
25℃
0℃
25℃
5V
3V
70℃
70℃
Fig. 34
Low Level Sink Current - Supply Voltage
(VOUT=0.2[V])
Fig. 35
Low Level Sink Current - Ambient Temperature
(VOUT=0.2[V])
Fig. 36
Input Offset Voltage - Supply Voltage
(Vicm=0[V], VOUT=1.4[V])
(*)The data above is ability value of sample, it is not guaranteed.
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
6/17
2011.06 - Rev.B
LM358DT/PT/ST/WDT/WPT,LM2904DT/PT/ST/WDT/WPT
LM324DT/PT/WDT,LM2902DT/PT/WDT
Technical Note
●Reference Data LM324 family
LM324 family
3V
25℃
0℃
5V
LM324 family
LM324 family
32V
32V
3V
5V
70℃
Fig. 37
Input Offset Voltage – Ambient Temperature
(Vicm=0[V], VOUT=1.4[V])
Fig. 38
Input Bias Current – Supply Voltage
(Vicm=0[V], VOUT=1.4[V])
Fig. 39
Input Bias Current – Ambient Temperature
(Vicm=0[V],VOUT=1.4[V])
LM324 family
LM324 family
LM324 family
0℃
70℃
25℃
0℃
25℃
70℃
[V]
Fig. 40
Input Bias Current – Ambient Temperature
(VCC=30[V],Vicm=28[V],VOUT=1.4[V])
Fig. 41
Input Offset Voltage – Common Mode Input Voltage
(VCC=5[V])
Fig. 42
Input Offset Current – Supply Voltage
(Vicm=0[V],VOUT=1.4[V])
LM324 family
LM324 family
LM324 family
25℃
0℃
15V
3V
5V
5V
32V
70℃
Fig. 43
Input Offset Current – Ambient Temperature
(Vicm=0[V],VOUT=1.4[V])
Fig. 44
Large Signal Voltage Gain – Supply Voltage
(RL=2[kΩ])
LM324 family
LM324 family
36V
0℃
Fig. 45
Large Signal Voltage Gain
– Ambient Temperature
(RL=2[kΩ])
LM324 family
32V
25℃
5V
70℃
Fig. 46
Common Mode Rejection Ratio
– Supply Voltage
3V
Fig. 47
Common Mode Rejection Ratio
– Ambient Temperature
Fig. 48
Power Supply Rejection Ratio
– Ambient Temperature
(*)The data above is ability value of sample, it is not guaranteed.
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
7/17
2011.06 - Rev.B
LM358DT/PT/ST/WDT/WPT,LM2904DT/PT/ST/WDT/WPT
LM324DT/PT/WDT,LM2902DT/PT/WDT
Technical Note
●Reference Data LM2904 family
LM2904 family
LM2904 family
LM2904 family
1.0
800
1.0
LM2904DT
LM2904WDT
400
200
SUPPLY CURRENT [mA]
LM2904ST
600
0.8
SUPPLY CURRENT [mA]
POWER DISSIPATION Pd [mW]
LM2904PT
LM2904WPT
25℃
－40℃
0.6
0.4
0
125℃
105℃
0.2
25
50
75
100
125
0.4
5V
3V
0.0
0
150
32V
0.6
0.2
0.0
0
0.8
10
AMBIENT TEMPERATURE : [℃]
Ta [℃]
Fig. 49
Derating Curve
20
30
SUPPLY VOLTAGE [V]
-50
40
Fig. 50
Supply Current – Supply Voltage
LM2904 family
40
0
25 50 75 100 125 150
AMBIENT TEMPERATURE [℃]
Fig. 51
Supply Current – Ambient Temperature
LM2904 family
5
-25
LM2904 family
50
-40℃
30
125℃
20
25℃
105℃
10
0
4
3
2
1
10
20
30
40
25℃
30
105℃
20
10
Fig. 52
Maximum Output Voltage – Supply Voltage
(RL=10[kΩ])
0
1
LM2904 family
100
15V
5V
30
15V
20
10
0
OUTPUT SINK CURRENT [mA]
OUTPUT SINK CURRENT [mA]
3V
10
125℃
1
-40℃
0.1
25℃
0.01
0
25
50
75
100 125 150
0
0.4
AMBIENT TEMPERATURE [℃]
Fig. 55
Output Source Current – Ambient Temperature
(VOUT=0[V])
25℃
60
50
40
125℃
105℃
30
20
10
5
0
25
50
75
100 125 150
AMBIENT TEMPERATURE [℃]
Fig. 57
Output Sink Current – Ambient Temperature
(VOUT=VCC)
LM2904 family
8
70
60
5V
50
40
3V
30
20
10
0
0
0
-25
32V
LOW LEVEL SINK CURRENT [μA]
70
3V
10
-50
LM2904 family
80
-40℃
5V
2
Fig. 56
Output Sink Current – Output Voltage
(VCC=5[V])
LM2904 family
80
0.8
1.2
1.6
OUTPUT VOLTAGE [V]
INPUT OFFSET VOLTAGE [mV]
-25
20
0
0.001
-50
5
LM2904 family
30
105℃
40
2
3
4
OUTPUT VOLTAGE [V]
Fig. 53
Fig. 54
Maximum Output Voltage – Ambient Temperature Output Source Current – Output Voltage
(VCC=5[V],RL=2[kΩ])
(VCC=5[V])
LM2904 family
50
125℃
0
-50 -25 0
25 50 75 100 125 150
AMBIENT TEMPERATURE [℃]
SUPPLY VOLTAGE [V]
LOW LEVEL SINK CURRENT [μA]
40
0
0
OUTPUT SOURCE CURRENT [mA]
OUTPUT SOURCE CURRENT [mA]
MAXIMUM OUTPUT VOLTAGE [V]
MAXIMUM OUTPUT VOLTAGE [V]
-40℃
10
15
20
25
SUPPLY VOLTAGE [V]
30
35
Fig. 58
Low Level Sink Current - Supply Voltage
(VOUT=0.2[V])
6
-40℃
25℃
4
2
0
-2
105℃
125℃
-4
-6
-8
-50
-25
0
25 50 75 100 125 150
AMBIENT TEMPERATURE [℃]
Fig. 59
Low Level Sink Current - Ambient Temperature
(VOUT=0.2[V])
0
5
10
15
20
25
SUPPLY VOLTAGE [V]
30
35
Fig. 60
Input Offset Voltage - Supply Voltage
(Vicm=0[V], VOUT=1.4[V])
(*)The data above is ability value of sample, it is not guaranteed.
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
8/17
2011.06 - Rev.B
LM358DT/PT/ST/WDT/WPT,LM2904DT/PT/ST/WDT/WPT
LM324DT/PT/WDT,LM2902DT/PT/WDT
Technical Note
●Reference Data LM2904 family
LM2904 family
8
LM2904 family
50
3V
2
0
5V
-2
32V
-4
40
30
20
10
105℃
40
32V
30
20
3V
10
5V
125℃
0
0
-25
0
25
50
75
0
100 125 150
AMBIENT TEMPERATURE [℃]
Fig. 61
Input Offset Voltage – Ambient Temperature
(Vicm=0[V], VOUT=1.4[V])
30
20
10
0
30
-50
35
-10
6
-40℃
25℃
125℃
2
0
-2
-4
-6
0
25
50
75
100 125 150
-1
0
AMBIENT TEMPERATURE [℃]
Fig. 64
Input Bias Current – Ambient Temperature
(VCC=30[V],Vicm=28[V],VOUT=1.4[V])
3V
0
5V
32V
-5
4
-10
130
-40℃
25℃
120
110
100
90
105℃
0
25
50
75
125℃
80
70
100 125 150
6
8
10
12
SUPPLY VOLTAGE [V]
25℃
100
80
125℃
105℃
60
40
0
10
20
30
SUPPLY VOLTAGE [V]
Fig. 70
Common Mode Rejection Ratio
– Supply Voltage
40
20
25
30
35
LM2904 family
140
130
15V
120
110
100
5V
90
80
70
14
-50
16
-25
0
25 50 75 100 125 150
AMBIENT TEMPERATURE [℃]
Fig. 69
Large Signal Voltage Gain
– Ambient Temperature
(RL=2[kΩ])
LM2904 family
COMMON MODE REJECTION RATIO [dB]
-40℃
120
15
Fig. 66
Input Offset Current – Supply Voltage
(Vicm=0[V],VOUT=1.4[V])
Fig. 68
Large Signal Voltage Gain – Supply Voltage
(RL=2[kΩ])
LM2904 family
140
10
60
4
AMBIENT TEMPERATURE [℃]
Fig. 67
Input Offset Current – Ambient Temperature
(Vicm=0[V],VOUT=1.4[V])
5
SUPPLY VOLTAGE [V]
140
36V
120
100
80
5V
3V
60
40
-50
-25
LM2904 family
140
32V
0
25 50 75 100 125 150
AMBIENT TEMPERATURE [℃]
Fig. 71
Common Mode Rejection Ratio
– Ambient Temperature
POWER SUPPLY REJECTION RATIO [dB]
-25
125℃
105℃
-5
0
60
-50
0
5
LM2904 family
140
LARGE SIGNAL VOLTAGE GAIN [dB]
5
25℃
-40℃
Fig. 65
Input Offset Voltage – Common Mode Input Voltage
(VCC=5[V])
LM2904 family
10
1
2
3
[V]
INPUT VOLTAGE [Vin]
LARGE SIGNAL VOLTAGE GAIN [dB]
-25
5
-10
-8
-50
LM2904 family
10
105℃
4
-25
0
25 50 75 100 125 150
AMBIENT TEMPERATURE [℃]
Fig. 63
Input Bias Current – Ambient Temperature
(Vicm=0[V],VOUT=1.4[V])
LM2904 family
8
INPUT OFFSET VOLTAGE [mV]
40
10
15
20
25
SUPPLY VOLTAGE [V]
Fig. 62
Input Bias Current – Supply Voltage
(Vicm=0[V], VOUT=1.4[V])
LM2904 family
50
5
INPUT OFFSET CURRENT [nA]
-50
INPUT BIAS CURRENT[nA]
25℃
-40℃
-6
INPUT OFFSET CURRENT [nA]
INPUT BIAS CURRENT [nA]
4
INPUT BIAS CURRENT [nA]
INPUT OFFSET VOLTAGE [mV]
6
-8
COMMON MODE REJECTION RATIO [dB]
LM2904 family
50
130
120
110
100
90
80
70
60
-50
-25
0
25
50
75
100 125 150
AMBIENT TEMPERATURE [℃]
Fig. 72
Power Supply Rejection Ratio
– Ambient Temperature
(*)The data above is ability value of sample, it is not guaranteed.
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
9/17
2011.06 - Rev.B
LM358DT/PT/ST/WDT/WPT,LM2904DT/PT/ST/WDT/WPT
LM324DT/PT/WDT,LM2902DT/PT/WDT
Technical Note
●Reference Data LM2902 family
LM2902 family
LM2902 family
1000
1.0
1.0
0.8
0.8
LM2902 family
SUPPLY CURRENT [mA]
600
400
LM2902DT
LM2902WDT
200
SUPPLY CURRENT [mA]
POWER DISSIPATION Pd [mW]
LM2902ST
800
25℃
－40℃
0.6
0.4
0.2
0
125℃
105℃
25
50
75
100
125
5V
3V
0.0
0
150
0.4
0.2
0.0
0
32V
0.6
10
AMBIENT TEMPERATURE : [℃]
Ta [℃]
Fig. 73
Derating Curve
20
30
SUPPLY VOLTAGE [V]
-50
40
Fig. 74
Supply Current – Supply Voltage
LM2902 family
40
0
25 50 75 100 125 150
AMBIENT TEMPERATURE [℃]
Fig. 75
Supply Current – Ambient Temperature
LM2902 family
5
-25
LM2902 family
50
-40℃
30
125℃
20
25℃
105℃
10
0
4
3
2
1
10
20
30
40
25℃
30
105℃
20
Fig. 76
Maximum Output Voltage – Supply Voltage
(RL=10[kΩ])
0
0
Fig. 77
Maximum Output Voltage – Ambient Temperature
(VCC=5[V],RL=2[kΩ])
LM2902 family
50
125℃
10
-50 -25 0
25 50 75 100 125 150
AMBIENT TEMPERATURE [℃]
SUPPLY VOLTAGE [V]
LM2902 family
100
1
5V
30
15V
20
10
15V
10
125℃
1
-40℃
0.1
25℃
0.01
0
25
50
75
100 125 150
0
0.4
AMBIENT TEMPERATURE [℃]
Fig. 79
Output Source Current – Ambient Temperature
(VOUT=0[V])
25℃
60
50
40
105℃
30
125℃
20
10
5
0
25
50
75
100 125 150
AMBIENT TEMPERATURE [℃]
Fig. 81
Output Sink Current – Ambient Temperature
(VOUT=VCC)
LM2902 family
8
70
60
5V
50
40
3V
30
20
10
0
0
0
-25
32V
LOW LEVEL SINK CURRENT [μA]
70
3V
10
-50
LM2902 family
80
-40℃
5V
2
Fig. 80
Output Sink Current – Output Voltage
(VCC=5[V])
LM2902 family
80
0.8
1.2
1.6
OUTPUT VOLTAGE [V]
INPUT OFFSET VOLTAGE [mV]
-25
20
0
0.001
-50
5
LM2902 family
30
OUTPUT SINK CURRENT [mA]
OUTPUT SINK CURRENT [mA]
3V
40
2
3
4
OUTPUT VOLTAGE [V]
Fig. 78
Output Source Current – Output Voltage
(VCC=5[V])
105℃
0
LOW LEVEL SINK CURRENT [μA]
40
0
0
OUTPUT SOURCE CURRENT [mA]
OUTPUT SOURCE CURRENT [mA]
MAXIMUM OUTPUT VOLTAGE [V]
MAXIMUM OUTPUT VOLTAGE [V]
-40℃
10
15
20
25
SUPPLY VOLTAGE [V]
30
35
Fig. 82
Low Level Sink Current - Supply Voltage
(VOUT=0.2[V])
6
-40℃
25℃
4
2
0
-2
105℃
125℃
-4
-6
-8
-50
-25
0
25 50 75 100 125 150
AMBIENT TEMPERATURE [℃]
Fig. 83
Low Level Sink Current - Ambient Temperature
(VOUT=0.2[V])
0
5
10
15
20
25
SUPPLY VOLTAGE [V]
30
35
Fig. 84
Input Offset Voltage - Supply Voltage
(Vicm=0[V], VOUT=1.4[V])
(*)The data above is ability value of sample, it is not guaranteed.
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
10/17
2011.06 - Rev.B
LM358DT/PT/ST/WDT/WPT,LM2904DT/PT/ST/WDT/WPT
LM324DT/PT/WDT,LM2902DT/PT/WDT
Technical Note
●Reference Data LM2902 family
LM2902 family
8
LM2902 family
50
3V
2
0
5V
-2
32V
-4
40
-40℃
20
10
105℃
40
32V
30
20
3V
10
5V
125℃
0
0
-25
0
25
50
75
0
100 125 150
AMBIENT TEMPERATURE [℃]
Fig. 85
Input Offset Voltage – Ambient Temperature
(Vicm=0[V], VOUT=1.4[V])
30
20
10
0
30
-50
35
-10
6
-40℃
4
125℃
2
0
-2
-4
-6
0
25
50
75
100 125 150
-1
0
AMBIENT TEMPERATURE [℃]
Fig. 88
Input Bias Current – Ambient Temperature
(VCC=30[V],Vicm=28[V],VOUT=1.4[V])
3V
0
5V
32V
-5
4
-10
130
-40℃
25℃
120
110
100
90
125℃
105℃
0
25
50
75
80
70
100 125 150
6
8
10
12
SUPPLY VOLTAGE [V]
25℃
100
125℃
80
105℃
60
40
0
10
20
30
SUPPLY VOLTAGE [V]
Fig. 94
Common Mode Rejection Ratio
– Supply Voltage
40
20
25
30
35
LM2902 family
140
130
15V
120
110
100
5V
90
80
70
14
-50
16
-25
0
25 50 75 100 125 150
AMBIENT TEMPERATURE [℃]
Fig. 93
Large Signal Voltage Gain
– Ambient Temperature
(RL=2[kΩ])
LM2902 family
COMMON MODE REJECTION RATIO [dB]
-40℃
120
15
Fig. 90
Input Offset Current – Supply Voltage
(Vicm=0[V],VOUT=1.4[V])
Fig. 92
Large Signal Voltage Gain – Supply Voltage
(RL=2[kΩ])
LM2902 family
140
10
60
4
AMBIENT TEMPERATURE [℃]
Fig. 91
Input Offset Current – Ambient Temperature
(Vicm=0[V],VOUT=1.4[V])
5
SUPPLY VOLTAGE [V]
140
36V
120
100
80
5V
3V
60
40
-50
-25
LM2902 family
140
32V
0
25 50 75 100 125 150
AMBIENT TEMPERATURE [℃]
Fig. 95
Common Mode Rejection Ratio
– Ambient Temperature
POWER SUPPLY REJECTION RATIO [dB]
-25
125℃
105℃
-5
0
60
-50
0
5
LM2902 family
140
LARGE SIGNAL VOLTAGE GAIN [dB]
5
25℃
-40℃
Fig. 89
Input Offset Voltage – Common Mode Input Voltage
(VCC=5[V])
LM2902 family
10
1
2
3
[V]
INPUT VOLTAGE [Vin]
LARGE SIGNAL VOLTAGE GAIN [dB]
-25
5
-10
-8
-50
LM2902 family
10
105℃
25℃
-25
0
25 50 75 100 125 150
AMBIENT TEMPERATURE [℃]
Fig. 87
Input Bias Current – Ambient Temperature
(Vicm=0[V],VOUT=1.4[V])
LM2902 family
8
INPUT OFFSET VOLTAGE [mV]
40
10
15
20
25
SUPPLY VOLTAGE [V]
Fig. 86
Input Bias Current – Supply Voltage
(Vicm=0[V], VOUT=1.4[V])
LM2902 family
50
5
INPUT OFFSET CURRENT [nA]
-50
INPUT BIAS CURRENT[nA]
25℃
30
-6
INPUT OFFSET CURRENT [nA]
INPUT BIAS CURRENT [nA]
4
INPUT BIAS CURRENT [nA]
INPUT OFFSET VOLTAGE [mV]
6
-8
COMMON MODE REJECTION RATIO [dB]
LM2902 family
50
130
120
110
100
90
80
70
60
-50
-25
0
25
50
75
100 125 150
AMBIENT TEMPERATURE [℃]
Fig. 96
Power Supply Rejection Ratio
– Ambient Temperature
(*)The data above is ability value of sample, it is not guaranteed.
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
11/17
2011.06 - Rev.B
LM358DT/PT/ST/WDT/WPT,LM2904DT/PT/ST/WDT/WPT
LM324DT/PT/WDT,LM2902DT/PT/WDT
Technical Note
●Circuit Diagram
+
Vcc
INVERTING
INPUT
OUTPUT
NON-INVERTING
INPUT
-
Vcc
Fig.97 Circuit Diagram (each Op-Amp)
●Measurement Circuit 1 NULL Method Measurement Condition
Parameter
VF
S1
S2
S3
+
-
Vcc , Vcc , EK, Vicm Unit: [V]
LM358/LM324 family
LM2904/LM2902 family
Calculation
Vcc+ Vcc- EK Vicm Vcc+ Vcc- EK Vicm
Input Offset Voltage
VF1 ON ON OFF 5 to 30
0
-1.4
0
5 to 30
0
-1.4
0
1
Input Offset Current
VF2 OFF OFF OFF
5
0
-1.4
0
5
0
-1.4
0
2
VF3 OFF ON
5
0
-1.4
0
5
0
-1.4
0
5
0
-1.4
0
5
0
-1.4
0
15
0
-1.4
0
15
0
-1.4
0
15
0
-11.4
0
15
0
-11.4
0
5
0
-1.4
0
5
0
-1.4
0
5
0
-1.4
3.5
5
0
-1.4
3.5
5
0
-1.4
0
5
0
-1.4
0
30
0
-1.4
0
30
0
-1.4
0
Input Bias Current
VF4 ON OFF
VF5
Large Signal Voltage Gain
VF6
Common-mode Rejection Ratio
VF7
VF8
VF9
Supply Voltage Rejection Ratio
VF10
OFF
ON
ON ON
ON
ON OFF
ON
ON OFF
－Calculation－
1. Input Offset Voltage (VIO)
3
4
5
6
0.1[μF]
VF1
Vio 
1+ Rf /Rs [V]
Rf
50[kΩ]
2. Input Offset Current (IIO)
500[kΩ]
Iio  VF2 - VF1 [A]
Ri (1+ Rf / Rs)
S1
Vcc+
0.1[μF]
VOUT EK
+15[V]
3. Input Bias Current (IIB)
Rs
VF4 - VF3
[A]
Ib 
2× Ri (1+ Rf / Rs)
Vicm
4. Large Signal Voltage Gain (AVD)
500[kΩ]
50[Ω] 10[kΩ]
50[Ω] 10[kΩ]
Rs
DUT
S3
Ri
1000[pF]
AV  20× Log 10× (1+ Rf /Rs) [dB]
VF6 - VF5
S2
Rf
5.Common-mode Rejection Ration (CMRR)
(1+ Rf/ Rs)
CMRR  20× Log 3.5×
VF8-VF7
Ri
Vcc-
RL
-15[V]
V
VF
50[kΩ]
[dB]
6. Supply Voltage Rejection Ration (SVR)
PSRR ＝20×Log
△Vcc +×(1+Rf/Rs)
VF10 - VF9
Fig.98 Measurement circuit1 (Each Op-Amps)
[dB]
△Vcc +=25V
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
12/17
2011.06 - Rev.B
LM358DT/PT/ST/WDT/WPT,LM2904DT/PT/ST/WDT/WPT
LM324DT/PT/WDT,LM2902DT/PT/WDT
Technical Note
●Measurement circuit2 Switch condition
SW
1
SW No.
SW
2
SW
3
SW
4
SW
5
SW
6
SW
7
SW
8
SW
9
SW
10
SW
11
SW
12
SW
13
SW
14
SW
15
Supply Current
OFF OFF OFF ON OFF OFF ON OFF OFF OFF OFF OFF OFF OFF OFF
High level Output Voltage
OFF OFF ON OFF OFF OFF ON OFF OFF ON OFF OFF OFF ON OFF
Low level Output Voltage
OFF OFF ON OFF OFF OFF ON OFF OFF OFF OFF OFF OFF ON OFF
Output source current
OFF OFF ON OFF OFF OFF ON OFF OFF OFF OFF OFF OFF OFF ON
Output sink current
OFF OFF ON OFF OFF OFF ON OFF OFF OFF OFF OFF OFF OFF ON
Slew Rate
OFF OFF OFF ON OFF OFF OFF OFF ON
Gain band width product
OFF ON OFF OFF OFF ON
Equivalent input noise voltage
ON OFF OFF OFF ON OFF ON OFF OFF OFF OFF ON OFF OFF OFF
ON
ON OFF OFF OFF OFF
ON OFF OFF ON
ON OFF OFF OFF OFF
Input voltage
3[V]
SW4
SW5
R2
SW6
R3
0.5[V]
Vcc +
Input waveform
A
Output voltage
－
SW1
SW2
RS
R1
SR ＝ ΔV / Δt
3[V]
＋
SW3
t
SW10 SW11 SW12 SW13 SW14 SW15
SW7
SW8
SW9
Vcc
-
ΔV
A
～
VIN-
RL
VIN+ ～
CL
V
～
Δt
V
VOUT
0.5[V]
t
Output waveform
Fig.99 Measurement circuit2 (Each Op-Amps)
Fig.100 Slew Rate Input Waveform
●Measurement Circuit3 Channel Separation
R2=100[kΩ]
R2=100[kΩ]
+
Vcc =+2.5[V]
Vcc+ =+2.5[V]
R1=1[kΩ]
R1=1[kΩ]
other
CH
CH1
VIN
V
R1//R2
Vcc- =-2.5[V]
VOUT1
=0.5 [Vrms]
R1//R2
VO1/VO2=20×log
Vcc-=-2.5[V]
V
VOUT2
100×VOUT1
VOUT2
Fig.101 Measurement Circuit3
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
13/17
2011.06 - Rev.B
LM358DT/PT/ST/WDT/WPT,LM2904DT/PT/ST/WDT/WPT
LM324DT/PT/WDT,LM2902DT/PT/WDT
Technical Note
●Description of Electrical Characteristics
Described below are descriptions of the relevant electrical terms
Please note that item names, symbols and their meanings may differ from those on another manufacturer’s documents.
1.Absolute maximum ratings
The absolute maximum ratings are values that should never be exceeded, since doing so may result in deterioration of electrical characteristics or damage to
the part itself as well as peripheral components.
1.1 Power supply voltage (Vcc+/Vcc-)
Expresses the maximum voltage that can be supplied between the positive and negative supply terminals without causing deterioration of the electrical
characteristics or destruction of the internal circuitry.
1.2 Differential input voltage (VID)
Indicates the maximum voltage that can be supplied between the non-inverting and inverting terminals without damaging the IC.
1.3 Input common-mode voltage range (VICM)
Signifies the maximum voltage that can be supplied to non-inverting and inverting terminals without causing deterioration of the characteristics or damage to
the IC itself. Normal operation is not guaranteed within the common-mode voltage range of the maximum ratings – use within the input common-mode
voltage range of the electric characteristics instead.
1.4 Operating and storage temperature ranges (Topr,Tstg)
The operating temperature range indicates the temperature range within which the IC can operate. The higher the ambient temperature, the lower the power
consumption of the IC. The storage temperature range denotes the range of temperatures the IC can be stored under without causing excessive
deterioration of the electrical characteristics.
1.5 Power dissipation (Pd)
Indicates the power that can be consumed by a particular mounted board at ambient temperature (25℃). For packaged products, Pd is determined by the
maximum junction temperature and the thermal resistance.
2. Electrical characteristics
2.1 Input offset voltage (VIO)
Signifies the voltage difference between the non-inverting and inverting terminals. It can be thought of as the input voltage difference required for setting the
output voltage to 0 V.
2.2 Input offset voltage drift (DVIO)
Denotes the ratio of the input offset voltage fluctuation to the ambient temperature fluctuation.
2.3 Input offset current (IIO)
Indicates the difference of input bias current between the non-inverting and inverting terminals.
2.4 Input offset current drift (DIIO)
Signifies the ratio of the input offset current fluctuation to the ambient temperature fluctuation.
2.5 Input bias current (IIB)
Denotes the current that flows into or out of the input terminal, it is defined by the average of the input bias current at the non-inverting terminal and the input
bias current at the inverting terminal.
2.6 Circuit current (ICC)
Indicates the current of the IC itself that flows under specified conditions and during no-load steady state.
2.7 High level output voltage/low level output voltage (VOH/VOL)
Signifying the voltage range that can be output under specified load conditions, it is in general divided into high level output voltage and low level output
voltage. High level output voltage indicates the upper limit of the output voltage, while low level output voltage the lower limit.
2.8 Large signal voltage gain (AVD)
The amplifying rate (gain) of the output voltage against the voltage difference between non-inverting and inverting terminals, it is (normally) the amplifying
rate (gain) with respect to DC voltage.
AVD = (output voltage fluctuation) / (input offset fluctuation)
2.9 Input common-mode voltage range (VICM)
Indicates the input voltage range under which the IC operates normally.
2.10 Common-mode rejection ratio (CMRR)
Signifies the ratio of fluctuation of the input offset voltage when the in-phase input voltage is changed (DC fluctuation).
CMRR = (change in input common-mode voltage) / (input offset fluctuation)
2.11 Power supply rejection ratio (SVR)
Denotes the ratio of fluctuation of the input offset voltage when supply voltage is changed (DC fluctuation).
SVR = (change in power supply voltage) / (input offset fluctuation)
2.12 Output source current/ output sink current (IOH/IOL)
The maximum current that can be output under specific output conditions, it is divided into output source current and output sink current. The output source
current indicates the current flowing out of the IC, and the output sink current the current flowing into the IC.
2.13 Channel separation (VO1/VO2)
Expresses the amount of fluctuation of the input offset voltage or output voltage with respect to the change in the output voltage of a driven channel.
2.14 Slew rate (SR)
Indicates the time fluctuation ratio of the output voltage when an input step signal is supplied.
2.15 Gain bandwidth product (GBP)
The product of the specified signal frequency and the gain of the op-amp at such frequency, it gives the approximate value of the frequency where the gain of
the op-amp is 1 (maximum frequency, and unity gain frequency).
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
14/17
2011.06 - Rev.B
LM358DT/PT/ST/WDT/WPT,LM2904DT/PT/ST/WDT/WPT
LM324DT/PT/WDT,LM2902DT/PT/WDT
Technical Note
●Derating curves
1000
LM358PT
LM358WPT
LM2904PT
LM2904WPT
POWER DISSIPATION Pd [mW]
POWER DISSIPATION Pd [mW]
800
LM358ST
600
LM2904ST
LM2904DT
LM2904WDT
400
LM358DT
LM358WDT
200
0
0
25
70
50
75
LM2902ST
800
LM2902DT
LM2902WDT
600
LM324PT
400
LM324DT
LM324WDT
200
0
100
125
150
0
AMBIENT TEMPERATURE [℃]
25
50
70
75
100
125
150
AMBIENT TEMPERATURE [℃]
LM358DR/PWR/DGKR
LM2904DR/PWR/DGKR/VQDR/VQPWR
LM324DR/PWR/KDR
LM2902DR/PWR/KDR/KPWR/KQDR/KQPWR
Power Dissipation
Power Dissipation
Pd[W]
θja [℃/W]
Package
Pd[W]
θja [℃/W]
SO package8 (*8)
450
3.6
SO package14
610
4.9
TSSOP8 (*6)
500
4.0
TSSOP14
870
7.0
Mini SO8 (*7)
470
3.76
Package
Fig.102 Derating Curves
●Precautions
Vcc +
1) Unused circuits
When there are unused circuits, it is recommended that they be connected as in Fig.103, setting
the non-inverting input terminal to a potential within the in-phase input voltage range (VICM).
2) Input terminal voltage
Applying Vcc- + 32V to the input terminal is possible without causing deterioration of the electrical
characteristics or destruction, irrespective of
the supply voltage. However, this does not ensure normal circuit operation. Please note that the
circuit operates normally only when the input voltage is
within the common mode input voltage range of the electric characteristics.
3) Power supply (single / dual)
The op-amp operates when the voltage supplied is between Vcc+ and Vcc-.
Therefore, the single supply op-mp can be used as a dual supply op-amp as well.
－
connect
to Vicm
＋
Vcc -
Fig.103 Disable circuit example
4) Power dissipation (Pd)
Using the unit in excess of the rated power dissipation may cause deterioration in electrical characteristics due to the rise in chip temperature, including
reduced current capability. Therefore, please take into consideration the power dissipation (Pd) under actual operating conditions and apply a sufficient
margin in thermal design. Refer to the thermal derating curves for more information.
5) Short-circuit between pins and erroneous mounting
Incorrect mounting may damage the IC. In addition, the presence of foreign substances between the outputs, the output and the power supply, or the output
and Vcc- may result in IC destruction.
6) Operation in a strong electromagnetic field
Operation in a strong electromagnetic field may cause malfunctions.
7) Radiation
This IC is not designed to withstand radiation.
8) IC handing
Applying mechanical stress to the IC by deflecting or bending the board may cause fluctuation of the electrical characteristics due to piezoelectric (piezo)
effects.
9) IC operation
The output stage of the IC is configured using Class C push-pull circuits. Therefore, when the load resistor is connected to the middle potential of Vcc+ and
Vcc-, crossover distortion occurs at the changeover between discharging and charging of the output current. Connecting a resistor between the output
terminal and Vcc-, and increasing the bias current for Class A operation will suppress crossover distortion.
10) Board inspection
Connecting a capacitor to a pin with low impedance may stress the IC. Therefore, discharging the capacitor after every process is recommended. In addition,
when attaching and detaching the jig during the inspection phase, ensure that the power is turned OFF before inspection and removal. Furthermore, please
take measures against ESD in the assembly process as well as during transportation and storage.
11) Output capacitor
Discharge of the external output capacitor to Vcc+ is possible via internal parasitic elements when Vcc+ is shorted to Vcc-, causing damage to the internal
circuitry due to thermal stress. Therefore, when using this IC in circuits where oscillation due to output capacitive load does not occur, such as in voltage
comparators, use an output capacitor with a capacitance less than 0.1μF.
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
15/17
2011.06 - Rev.B
LM358DT/PT/ST/WDT/WPT,LM2904DT/PT/ST/WDT/WPT
LM324DT/PT/WDT,LM2902DT/PT/WDT
Technical Note
●Ordering part number
L
M
2
9
0
2
Family name
LM358
LM324
LM2902
LM2904
W
D
ESD Tolerance
applicable
T
Package type
D : S.O package
P : TSSOP
S : Mini SO
W : 2kV
None : Normal
Packaging and forming specification
R: Embossed tape and reel
S.O package8
<Tape and Reel information>
4.9±0.2
(MAX 5.25 include BURR)
6
5
0.45Min.
7
3.9±0.2
6.0±0.3
8
4° +6°
−4°
1
2
3
Tape
Embossed carrier tape
Quantity
2500pcs
Direction
of feed
( reel on the left hand and you pull out the tape on the right hand
The direction is the 1pin of product is at the upper left when you hold
)
4
0.545
0.2±0.1
0.175
1.375±0.1
S
1.27
0.42±0.1
1pin
0.1 S
Reel
(Unit : mm)
Direction of feed
∗ Order quantity needs to be multiple of the minimum quantity.
S.O package14
<Tape and Reel information>
8.65±0.1
(Max 9.0 include BURR)
0.65± 0.15
1
Tape
Embossed carrier tape
Quantity
2500pcs
Direction
of feed
( reel on the left hand and you pull out the tape on the right hand
The direction is the 1pin of product is at the upper left when you hold
)
7
1PIN MARK
0.175± 0.075
S
+0.05
0.22 −0.03
1.375 ± 0.075
1.65MAX
0.515
1.05±0.2
8
6.0 ± 0.2
3.9 ± 0.1
14
4° +6°
−4°
+0.05
0.42 −0.04
1.27
0.08 S
0.08 M
1pin
Reel
(Unit : mm)
Direction of feed
∗ Order quantity needs to be multiple of the minimum quantity.
TSSOP8
<Tape and Reel information>
3.0±0.1
(MAX 3.35 include BURR)
7
6
0.5 ± 0.15
3
2500pcs
Direction
of feed
( reel on the left hand and you pull out the tape on the right hand
4
1PIN MARK
The direction is the 1pin of product is at the upper left when you hold
)
1.0±0.2
2
Embossed carrier tape
Quantity
+0.05
0.145 −0.03
0.1 ± 0.05
S
1.0 ± 0.05
1.2MAX
1
0.525
Tape
5
6.4 ± 0.2
4.4 ± 0.1
8
4±4
0.08 S
+0.05
0.245 −0.04
0.08
M
1pin
0.65
(Unit : mm)
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
Reel
16/17
Direction of feed
∗ Order quantity needs to be multiple of the minimum quantity.
2011.06 - Rev.B
LM358DT/PT/ST/WDT/WPT,LM2904DT/PT/ST/WDT/WPT
LM324DT/PT/WDT,LM2902DT/PT/WDT
Technical Note
TSSOP14
<Tape and Reel information>
5.0±0.1
(Max 5.35 include BURR)
4 ±4
14
1
Tape
Embossed carrier tape
Quantity
2500pcs
Direction
of feed
( reel on the left hand and you pull out the tape on the right hand
The direction is the 1pin of product is at the upper left when you hold
)
7
1PIN MARK
+0.05
0.145 −0.03
0.1±0.05
S
1.0±0.05
1.2MAX
0.55
1.0±0.2
0.5±0.15
6.4±0.2
4.4±0.1
8
0.08 S
+0.05
0.245 −0.04
0.65
0.08
1pin
M
Reel
(Unit : mm)
Direction of feed
∗ Order quantity needs to be multiple of the minimum quantity.
Mini SO8
<Tape and Reel information>
3.0±0.1
(MAX 3.35 include BURR)
6
5
0.45 ± 0.15
2
3
4
1PIN MARK
Tape
Embossed carrier tape
Quantity
2500pcs
Direction
of feed
( reel on the left hand and you pull out the tape on the right hand
The direction is the 1pin of product is at the upper left when you hold
)
0.95 ± 0.2
1
+0.05
0.145 −0.03
0.525
0.1±0.05
S
0.85±0.05
1.1MAX
7
3.0 ± 0.1
4.9± 0.2
8
4±4
0.08 S
+0.05
0.32 −0.04
0.08
M
1pin
0.65
(Unit : mm)
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
Reel
17/17
Direction of feed
∗ Order quantity needs to be multiple of the minimum quantity.
2011.06 - Rev.B
Datasheet
Notice
Precaution on using ROHM Products
1.
Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment,
OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you
(Note 1)
, transport
intend to use our Products in devices requiring extremely high reliability (such as medical equipment
equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car
accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or
serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance.
Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any
damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific
Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN
USA
EU
CHINA
CLASSⅢ
CLASSⅡb
CLASSⅢ
CLASSⅢ
CLASSⅣ
CLASSⅢ
2.
ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3.
Our Products are designed and manufactured for use under standard conditions and not under any special or
extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any
special or extraordinary environments or conditions. If you intend to use our Products under any special or
extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of
product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4.
The Products are not subject to radiation-proof design.
5.
Please verify and confirm characteristics of the final or mounted products in using the Products.
6.
In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7.
De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual
ambient temperature.
8.
Confirm that operation temperature is within the specified range described in the product specification.
9.
ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Precaution for Mounting / Circuit board design
1.
When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2.
In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the
ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Notice - GE
© 2014 ROHM Co., Ltd. All rights reserved.
Rev.002
Datasheet
Precautions Regarding Application Examples and External Circuits
1.
If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2.
You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
Precaution for Storage / Transportation
1.
Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2.
Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3.
Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4.
Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
Precaution for Product Label
QR code printed on ROHM Products label is for ROHM’s internal use only.
Precaution for Disposition
When disposing Products please dispose them properly using an authorized industry waste company.
Precaution for Foreign Exchange and Foreign Trade act
Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act,
please consult with ROHM representative in case of export.
Precaution Regarding Intellectual Property Rights
1.
All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable
for infringement of any intellectual property rights or other damages arising from use of such information or data.:
2.
No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the information contained in this document.
Other Precaution
1.
This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
2.
The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
3.
In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
4.
The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Notice - GE
© 2014 ROHM Co., Ltd. All rights reserved.
Rev.002
Datasheet
General Precaution
1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents.
ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny
ROHM’s Products against warning, caution or note contained in this document.
2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s
representative.
3.
The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or
liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or
concerning such information.
Notice – WE
© 2014 ROHM Co., Ltd. All rights reserved.
Rev.001