Download Switch mode power supply controller

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Spark-gap transmitter wikipedia , lookup

Wien bridge oscillator wikipedia , lookup

Regenerative circuit wikipedia , lookup

Index of electronics articles wikipedia , lookup

Integrating ADC wikipedia , lookup

TRIAC wikipedia , lookup

Surge protector wikipedia , lookup

Resistive opto-isolator wikipedia , lookup

Immunity-aware programming wikipedia , lookup

Audio power wikipedia , lookup

Amplifier wikipedia , lookup

Power MOSFET wikipedia , lookup

Voltage regulator wikipedia , lookup

Wilson current mirror wikipedia , lookup

Schmitt trigger wikipedia , lookup

CMOS wikipedia , lookup

Transistor–transistor logic wikipedia , lookup

Operational amplifier wikipedia , lookup

Radio transmitter design wikipedia , lookup

Valve RF amplifier wikipedia , lookup

Valve audio amplifier technical specification wikipedia , lookup

Power electronics wikipedia , lookup

Current mirror wikipedia , lookup

Opto-isolator wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Rectiverter wikipedia , lookup

Transcript
TEA2261/0
SWITCH MODE POWER SUPPLY CONTROLLER
Positive and Negative Current up to 1.2A and 2A
■ Low Start-Up Current
■ Direct Drive of the Power Transistor
■ Two Levels Transistor Current Limitation
■ Double Pulse Suppression
■ Soft-Starting
■ Under and Overvoltage Lock-out
■ Automatic Stand-By Mode Recognition
■ Large Power Range Capability in Stand-By
(Burst Mode)
■ Internal PWM Signal Generator
DESCRIPTION
The TEA2260/61 is a monolithic integrated circuit
for the use in primary part of an off-line switching
mode power supply.
All functions required for SMPS control under normal operating, transient or abnormal conditions
are provided.
The capability of working according to the “master-slave” concept, or according to the “primary
regulation” mode makes the TEA2260/61 very
flexible and easy to use. This is particularly true for
TV receivers where the IC provides an attractive
and low cost solution (no need of stand-by auxiliary power supply). See application note AN376/
0490 for detailed information.
■
)
s
(
ct
c
u
d
e
t
le
o
s
b
O
-
)
s
t(
o
r
P
BATWING DIP16
(Plastic Package)
ORDER CODES:
TEA2261/0
u
d
o
r
P
e
t
e
l
o
TRANSFORMER DEMAGNETIZATION SENSING INPUT
IS
1
16
V CC
POWER SUPPLY
SECONDARY PULSES INPUT
IN
2
15
V+
POSITIVE OUTPUT STAGE SUPPLY
POWER TRANSISTOR CURRENT LIMITATION INPUT
I MAX
3
14
OUT
POWER OUTPUT
GROUND GND
4
13
GND GROUND
GROUND GND
5
12
GND GROUND
ERROR AMPLIFIER INPUT (INVERTING)
E
6
11
R0
OSCILLATOT RESISTOR
ERROR AMPLIFIER OUTPUT
S
7
10
C0
OSCILLATOR CAPACITOR
OVERLOAD INTEGRATION CAPACITOR
C2
8
9
C1
SOFT-START CAPACITOR
s
b
O
October 2003
2261-01.eps
Figure 1. Pin Connections
1/11
1
TEA2261/0
Figure 2. Block Diagram
S
VCC
16
7
V+
15
INTERNAL
BIAS
-
VCC MONITORING
+
OVERVOLTAGE
PROTECTION
7.4V
VREF (2.49V)
-
MODULATOR
LOGIC
+
PRIMARY
PULSES
POSITIVE
OUTPUT
STAGE
REGULATION
PULSES
IS
LOGIC
MODULATORS
10.3V
LOGIC
PROCESSOR
+
-
-
9
11
10
1
2
C1
R0
C0
IS IN
)
s
(
ct
u
d
o
2/11
1
0.9V
e
t
le
2.55V
SECONDARY
PULSE
s
b
O
0.6V
0.15V
10µ A
o
s
b
O
-
8
C2
)
s
t(
- 2A
o
r
P
+
+
-
+
OSCILLATOR
OUT
(Max.)
c
u
d
CURRENT
LIMITATION
-
45µ A
+
DEMAGNETIZATION
SENSING
t
e
l
o
14
NEGATIVE
OUTPUT
STAGE
REPETITIVE
OVERLOAD
PROTECTION
r
P
e
(Max.)
VCC
AUTOMATIC
BURST
GENERATION
TON(Max.) (60%)
SOFT-START
+ 1.2A
3
I MAX
-
4
5
12 13
GND
2261-04.eps
VREF
2.49V
-1
-
E 6
+
15.7V
ERROR AMPLIFLIER
TEA2261/0
SIMPLIFIED APPLICATION DIAGRAMS
Figure 3. Master-Slave Concept
Muting
Control
AUDIO
OUTPUT
STAGE
R
P1
MAINS
INPUT
Synchronization
Remote
Stand-by
SCANNING
DEVICE
P2
C
VOLTAGE
REGULATOR
Remote
Stand-by
V CC
TEA2260/61
SLAVE
TEA5170
MASTER
)
s
t(
µP
uc
VCC
d
o
r
PWM
Power primary ground
Secondary ground (isolated from mains)
P 2 : Output voltage adjustement in stand-by
o
s
b
O
-
Figure 4. Secondary Regulation (with optocoupler)
MAINS
INPUT
)
s
(
ct
u
d
o
r
P
e
t
e
l
o
bs
O
2261-02.eps
P
e
let
P 1 : Output voltage adjustement in normal mode
R
INFRA-RED
RECEIVER
AUDIO
OUTPUT
STAGE
P
SCANNING
DEVICE
Muting
Control
Remote
Stand-by
C
VOLTAGE
REGULATOR
VCC
TEA2260/61
µP
VCC
P : Output voltage adjustement
Power primary ground
Secondary ground (isolated from mains)
2261-03.eps
INFRA-RED
RECEIVER
3/11
1
TEA2261/0
ABSOLUTE MAXIMUM RATINGS
Symbol
VCC
V+
IOUT+
IOUT Tj
Tstg
Parameter
Power Supply V16-V4, 5, 12, 13
Output Stage Power Supply V15-V4, 5, 12, 13
Positive Output Current (source current)
Negative Output Current (sink current)
Operating Junction Temperature
Storage Temperature Range
Value
20
20
1.5
2.5
150
-40, +150
Unit
V
V
A
A
oC
oC
Value
11
45
oC/W
THERMAL DATA
Symbol
Rth (j-c)
Rth (j-a)
Parameter
Junction-case Thermal Resistance
Junction-ambient Thermal Resistance
Unit
oC/W
c
u
d
e
t
le
)
s
(
ct
u
d
o
r
P
e
t
e
l
o
s
b
O
4/11
1
o
s
b
O
-
o
r
P
)
s
t(
TEA2261/0
RECOMMENDED OPERATING CONDITIONS
Symbol
VCC
IOUT +
IOUTIOUT +
IOUTFoper
VIN
ROSC
COSC
C1
C2
C2/C1
Tamb
Parameter
Min.
VCC stop
Power Supply
Positive Output Current (source current)
Negative Output Current (sink current)
Average Positive Output Current
Average Negative Output Current
Operating Frequency
Input Pulses Amplitude (Pin 2)
Oscillator Resistor Range
Oscillator Capacitor Range
Soft-starting Capacitor Range
Overload Integration Capacitor
Ratio C2/C1 (C2 must be ≤ C1)
Operating Ambient Temperature
10
1.5
20
0.47
0.047
0.047
1
-20
Typ.
12
2.5
Max.
VCC max
1.2
2.0
0.6
0.6
100
4.5
150
4.7
1
1
70
ELECTRICAL CHARACTERISTICS (Tamb = 25oC, VCC =12V, unless otherwise specified)
Symbol
Parameter
POWER SUPPLY
VCC(start) Starting Voltage (VCC increasing)
VCC(stop) Stopping Voltage (VCC decreasing)
Hyst VCC Hysteresis (VCC(start) - VCC(Stop))
ICC(start) Starting Current (VCC = 9V)
Supply Current (VCC = 12V)
ICC
VCC(max) Overvoltage Threshold on VCC
ICC(over) Supply Current after Overvoltage Detection (VCC = 17V)
OSCILLATOR / PWM SECTION
Delta ⋅ F
-----------------------F
Accuracy (ROSC = 68kΩ, COSC = 1nF)
)
s
(
ct
tON max Maximum Duty Cycle in Primary Regulation Mode
ERROR AMPLIFIER SECTION
Open Loop Gain
AVO
Unity Gain Frequency
Fug
Short Circuit Output Current (Pin 7 connected to ground)
ISC
E Input Bias Current (Pin 6)
IBE
Internal Voltage Reference (connected to error amplifier input
VREF
and not directly accessible)
INPUT SECTION
VIN
IN Input Threshold (Pin 2)
IS Input Threshold (Pin 1)
VIS
IN Input Bias Current
IBIN
IS Input Bias Current
IBIS
CURRENT LIMITATION SECTION
First Current Limitation Threshold
VIM1
Second Current Limitation Threshold
VIM2
Thresholds Difference VIM2 - VIM1
DVIM
Lock-out Threshold on Pin C2
VC2
Capacitor C2 Discharge Current
IDC2
Capacitor C2 Charge Current
ICC2
IBI(max) Maximum Input Bias Current (Pin 3)
u
d
o
r
P
e
s
b
O
t
e
l
o
Typ.
9.3
6.4
2.4
10.3
7.4
2.9
0.7
7.5
15.7
35
e
t
le
so
b
O
-
Min.
15
26
Max.
o
r
P
c
u
d
11.3
8.4
1.4
15
42
10
50
60
Unit
V
A
A
A
A
kHz
V
kΩ
nF
µF
µF
o
C
)
s
t(
Unit
V
V
V
mA
mA
V
mA
%
70
75
550
2
0.08
%
dB
kHz
mA
µA
2.34
2.49
2.64
V
0.6
0.85
0.15
0.3
0.4
1.2
V
V
µA
µA
558
837
600
900
300
2.55
10
45
0.2
642
963
mV
mV
mV
V
µA
µA
µA
2.25
2.85
5/11
1
TEA2261/0
GENERAL DESCRIPTION
The TEA2260/61 is an off-line switch mode power
supply controller. The synchronization function
and the specific operation in stand-by mode make
it well adapted to video applications such as TV
sets, VCRs, monitors, etc..
The TEA2260/61 can be used in two types of architectures:
– Master/Slave architecture. In this case, the
TEA2260/61 drives the power transistor according to the pulse width modulated signals generated by the secondary located master circuit. A
pulse transformer provides the feedback (see
Figure 1).
– Conventional architecture with linear feedback
signal (feedback sources: optocoupler or transformer winding) (see Figure 2).
Using the TEA2260/61, the stand-by auxiliary
power supply, often realized with a small but costly
50Hz transformer, is no longer necessary. The
burst mode operation of the TEA2260/61 makes
possible the control of very low output power
(down to less than 1W) with the main power transformer.
When used in a master/slave architecture, the
TEA2260/61 and also the power transistor turn-off
can be easily synchronized with the line transformer. The switching noise cannot disturb the picture
in this case.
As an S.M.P.S. controller, the TEA2260/61 features the following functions:
– Power supply start-up (with soft-start)
– PWM generator
– Direct power transistor drive (+1.2A, -2.0A)
– Safety functions: pulse by pulse current limitation, output power limitation, over and under voltage lock-out.
S.M.P.S. OPERATING DESCRIPTION
)
s
(
ct
u
d
o
r
P
e
s
b
O
6/11
1
c
u
d
e
t
le
o
s
b
O
-
Starting Mode - Stand By Mode
Power for circuit supply is taken from the mains
through a high value resistor before starting. As
long as V CC of the TEA2260/61 is below VCC start,
the quiescent current is very low (typically 0.7mA)
and the electrolytic capacitor across V CC is linearly
charged. When VCC reaches VCC start (typically
10.3V), the circuit starts, generating output pulses
with a soft-starting. Then the SMPS goes into the
stand-by mode and the output voltage is a percentage of the nominal output voltage (e.g. 80%).
To do this, the TEA2260/61 contains all the functions required for primary mode regulation: a fixed
frequency oscillator, a voltage reference, an error
amplifier and a pulse width modulator (PWM).
t
e
l
o
For transmission of low power with a good efficiency in stand-by, an automatic burst generation system is used, in order to avoid audible noise.
Normal Mode (Secondary Regulation)
The normal operating of the TV set is obtained by
sending to the TEA2260/61 regulation pulses generated by a regulator located in the secondary side
of the power supply.
This architecture uses the “Master/Slave Concept”, advantages of which are now well-known
especially the very high efficiency in Stand-by
mode, and the accurate regulation in Normal
mode.
Stand-by mode or normal mode are obtained by
supplying or not the secondary regulator. This can
be ordonnered for example by a microprocessor in
relation with the remote control unit.
Regulation pulses are applied to the TEA2260/61
through a small pulse-transformer to the IN input
(Pin 2). This input is sensitive to positive square
pulses. The typical threshold of this input is 0.85V.
The frequency of pulses coming from the secondary regulator can be lower or higher than the frequency of the starting oscillator.
The TEA2260/61 has no soft-starting system
when it receives pulses from the secondary. The
soft-start must be located in the secondary regulator.
Due to the principle of the primary regulation, pulses generated by the starting system automatically
disappear when the voltage delivered by the
SMPS increases.
Stand-by Mode - Normal Mode Transition
During the transition there are simultaneously
pulses coming from the primary and secondary
regulators.
These signals are not synchronized and some
care has to be taken to ensure the safety of the
switching power transistor.
A very sure and simple way consist in checking the
transformer demagnetization state.
– A primary pulse is taken in account only if the
transformer is demagnetized after a conduction
of the power transistor required by the secondary
regulator.
– A secondary pulse is taken in account only if the
transformer is demagnetized after a conduction
of the power transistor required by the primary
regulator.
With this arrangement the switching safety area of
the power transistor is respected and there is no
risk of transformer magnetization.
o
r
P
)
s
t(
TEA2261/0
The magnetization state of the transformer is
checked by sensing the voltage across a winding
of the transformer (generally the same which sup-
plies the TEA2261). This is made by connecting a
resistor between this winding and the demagnetization sensing input of the circuit (Pin 1).
SECURITY FUNCTIONS OF THE TEA2260 (see flowchart below)
Undervoltage Detection. This protection works in
association with the starting device “V CC switch”
(see paragraph Starting-mode - stand-by mode). If
VCC is lower than VCCstop (typically 7.4V) output
pulses are inhibited, in order to avoid wrong operation of the power supply or bad power transistor
drive.
Overvoltage Detection. If VCC exceeds V CCmax
(typically 15.7V) output pulses are inhibited. Restarting of the power supply is obtained by reducing VCC below VCCstop.
Current Limitation of the Power Transistor. The
current is measured by a shunt resistor. A double
threshold system is used:
– When the first threshold (VIM1) is reached, the
conduction of the power transistor is stopped until the end of the period: a new conduction signal
is needed to obtain conduction again.
– Furthermore as long as the first threshold is
reached (it means during several periods), an external capacitor C2 is charged. When the voltage
)
s
(
ct
across the capacitor reaches VC2 (typically
2.55V) the output is inhibited. This is called the
“repetitive overload protection”. If the overload
disappears before VC2 is reached, C2 is discharged, so transient overloads are tolerated.
– Second current limitation threshold (VIM2). When
this threshold is reached the output of the circuit
is immediately inhibited. This protection is helpful
in case of hard overload for example to avoid the
magnetization of the transformer.
Restart of the Power Supply. After stopping due
to VC2, VIM2, V CCMax or VCCstop triggering, restart of the power supply can be obtained by the
normal operating of the “VCC switch” but thanks to
an integrated counter, if normal restart cannot be
obtained after three trials, the circuit is definitively
stopped. In this case it is necessary to reduce VCC
below approximately 5V to reset the circuit. From a
practical point of view, it means that the power
supply has to be temporarily disconnected from
any power source to get the restart.
c
u
d
e
t
le
)
s
t(
o
r
P
o
s
b
O
-
u
d
o
r
P
e
t
e
l
o
s
b
O
7/11
TEA2261/0
Figure 5. Security Flowchart (TEA2260)
S.M.P.S.
starting
First
threshold reached
VIM1
Y
N
Y
Second
threshold reached
VIM2
N
Pulse by pulse current
limiting C 2 charged
VC2 < 2.6V
VCC max
reached
Y
Y
c
u
d
N
S.M.P.S. stopping
VCC stop reached
N=N+1
N
Normal operating
C 2 discharged
Restart
number = 3
N
e
t
le
)
s
t(
o
r
P
Reset C 2
discharged
Y
)
s
(
ct
u
d
o
r
P
e
t
e
l
o
s
b
O
8/11
o
s
b
O
N
Definitive
stopping
2261-06.eps
Y
TEA2261/0
SECURITY FUNCTIONS OF THE TEA2261 (see flowchart below)
– Furthermore as long as the first threshold is
reached (it means during several periods), an external capacitor C2 is charged. When the voltage
across the capacitor reaches VC2 (typically
2.55V) the output is inhibited. This is called the
“repetitive overload protection”. If the overload
disappears before VC2 is reached, C2 is discharged, so transient overloads are tolerated.
– Second current limitation threshold (VIM2). When
this threshold is reached the output of the circuit
is immediately inhibited. This protection is helpful
in case of hard overload for example to avoid the
magnetization of the transformer.
Restart of the Power Supply. After stopping due
to VIM2, VCCMax or V CCstop triggering, restart of
the power supply can be obtained by the normal
operating of the “VCC switch” VCC switch sequency
from VCCstop to VCCstart. After stopping due to
VC2 threshold reaching, the circuit is definitively
stopped. In this case it is necessary to reduce VCC
below approximately 5V to reset the circuit. From a
practical point of view, it means that the power
supply has to be temporarily disconnected from
any power source to get the restart.
Undervoltage Detection. This protection works in
association with the starting device “V CC switch”
(see paragraph Starting-mode - stand-by mode). If
VCC is lower than VCCstop (typically 7.4V) output
pulses are inhibited, in order to avoid wrong operation of the power supply or bad power transistor
drive.
Overvoltage Detection. If VCC exceeds V CCmax
(typically 15.7V) output pulses are inhibited and
the external capacitor C 2 is charged as long as
VCC is higher than VCC stop. Restarting of the
power supply is obtained by reducing VCC below
VCCstop except if the voltage across C2 reaches
VC2 (typically 2.55V) (refer to “Restart of the power
supply” paragraph).In this last case, the circuit is
definitively stopped.
Current Limitation of the Power Transistor. The
current is measured by a shunt resistor. A double
threshold system is used:
– When the first threshold (VIM1) is reached, the
conduction of the power transistor is stopped until the end of the period: a new conduction signal
is needed to obtain conduction again.
c
u
d
e
t
le
Figure 6. Security Flowchart (TEA2260)
S.M.P.S.
starting
u
d
o
)
s
(
ct
N
r
P
e
t
e
l
o
O
bs
VCCmax
reached
N
o
r
P
o
s
b
O
-
Y
Second
threshold reached
VIM2
Y
N
Pulse by pulse current
limiting C2 charged
Y
C2 charged
S.M.P.S. stopped
Normal operating
C 2 discharged
VC2 < 2.6V
VC2 < 2.6V
Y
Y
N
N
Definitive
stopping
Reset C2
discharged
Y
N
2261-76.eps
First
threshold reached
VIM1
)
s
t(
9/11
TEA2261/0
TYPICAL APPLICATION (Master/Slave Architecture)
4 x 1N4007
3
BY218-600
13
270 VAC
150µ F
385V
1k Ω
3.3
nF
22k Ω
1nF
1k Ω
1N4148
2.2 Ω /0.5W
P2
2.2µ F
16V
6
19
9
14
BA157
10 Ω
1W
PLR811
20
39 Ω
4.7k Ω
330µ F
25V
7
6
4
5
12
13
16
17
BY218-100
15
TEA2260/61
9
8
3
330
1nF nF
2.2k Ω
1000µ F
25V
10k Ω
25V
1A
1000µ F
25V
1
2.2µ H
1nF
82kΩ
120k Ω
Stand-by
control
75
kΩ
1.2nF
22k Ω
14
SGSF
344
47µ F
330
nF
330 Ω
18 Ω
BZX85-3V0
0.135 Ω /1W
BY299
2
100 Ω
10
47kΩ
100µ F
250V
BC547C
21
11
12V
0.5A
470µ F
25V
7.5V
1A
BY218-100
22
7
2
10µ F
16V
220 Ω
16W
4
6
5
TEA5170
3
2.7nF
1kV
7
8
560
pF
2%
1
47nF
c
u
d
1N4148
100pF
Small signal secondary ground
Power primary ground
Secondary ground (isolated from mains)
1k Ω
270 Ω
f
: 32kHz
Input voltage range
Input DC voltage range
Output power in normal mode
Output power in stand by mode
Operating frequency
Efficiency at full load
Efficiency in stand by mode
Short circuit protected
Open load protected
Long duration overload protected
Complete shutdown after repetitive default detection
)
s
(
ct
u
d
o
o
r
P
100k Ω
1%
POUT : 140W
TV - SET SMPS (with TEA5170)
e
t
le
o
s
b
O
-
170VAC - 270VAC
210VDC - 370VDC
25W < PO < 140W
2W < PO < 45W
32 kHz
> 80%
> 50%
r
P
e
t
e
l
o
Load Regulation (VDC = 310V)
bs
Output 135V (± 0.18%)
Output 25V (± 2%)
O
-> (I135 : 0.01A to 0.8A ; I25 = 1A)
-> (I135 : 0.8A ; I25 : 0.5A --> 1A)
Line Regulation
Output 135V (± 0.13%)
Output 25V (± 0.17%)
10/11
135V
0.8A
P1
22k Ω
3W
-> (210V < VDC < 370V)
-> (I135 : 0.8A ; I25 : 1A)
)
s
t(
150pF
6.8k Ω
Sync.
input
2261-08.eps
170 VAC
TEA2261/0
PACKAGE MECHANICAL DATA
16-PINS - PLASTIC DIP
I
b1
L
a1
Figure 7. 16-Pin Package
b
Z
B
e
E
e3
D
9
1
8
c
u
d
F
16
e
t
le
)
s
(
ct
)
s
t(
o
r
P
o
s
b
O
-
u
d
o
r
P
e
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences
of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted
by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject
to change without notice.This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not
authorized for use as critical components in life support devices or systems without the express written approval of STMicroelectronics.
t
e
l
o
s
b
O
The ST logo is a registered trademark of STMicroelectronics
2003 STMicroelectronics - All Rights Reserved.
Purchase of I2C Components by STMicroelectronics conveys a license under the Philips I2C Patent. Rights to use these components in an
I2C system is granted provided that the system conforms to the I2C Standard Specification as defined by Philips.
STMicroelectronics Group of Companies
Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - U.S.A.
http://www.st.com
11/11