Download A/D Type MCU

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Opto-isolator wikipedia , lookup

Multidimensional empirical mode decomposition wikipedia , lookup

Rectiverter wikipedia , lookup

Pulse-width modulation wikipedia , lookup

Analog-to-digital converter wikipedia , lookup

Immunity-aware programming wikipedia , lookup

Transcript
HT46 A/D Type MCU Series
HT46R25* (OTP)
HT46C25* (Mask)
Program Memory
16Kx16
HT46R24 (OTP)
HT46C24 (Mask)
8Kx16
HT46R23 (OTP)
HT46C23 (Mask)
4Kx15
HT46R22 (OTP)
HT46C22 (Mask)
2Kx14
64
192
* Under development,
available in 4Q, 2004
384
576
Data Memory (Byte)
HT46 A/D Type MCU Series
Features of A/D Type HT46 Series
• RISC Architecture
• Direct and Indirect
Addressing mode.
• Total 63 instructions.
• Table read function.
• Maximum 16 stack ( by
product)
• Operating Voltage:
– Fsys = 4Mhz, 2.2~5.5v
– Fsys = 8Mhz, 3.3~5.5v
• Idd : 2mA (tpy.) (5V,
4MHz, Xtal, ADC
disable)
• Istb : 1uA (max.)
(WDT, RTC disabled).
• -40oC~85oC Operating
temperature.(Industrial
grade)
Peripheral Feature
• I/O with pull high
function.
• Port A with wake up
function.
• Timer function
• Watch dog function
• Halt and wakeup for
low power consumption.
• I2C interface
• PFD driver output.
• On-chip crystal and RC
oscillator
• LVR for Brown-out
protection.
• Multi-channel 9 or 10-bit
A/D converter
• Pulse Width Modulator
output.
Block Diagram
Program Memory Map
Special Purpose Data Memory
General Purpose Data Memory
• 2 banks of Data memory in HT46X24
– Each one has 192x8 bytes (total 384 bytes).
– Need to use BP(bank pointer in special RAM) to select Bank0 or Bank1
data memory.
• BP=0 Access Bank0 data.
• BP=1 Access Bank1 data.
– Only use MP1 by Indirect Addressing mode to access.
PWM
• PWM is Pulse Width Modulator.
• There are two modes 6+2 or 7+1 selected by
configuration.
• User can change the frequency duty software
– by writing data to PWM0~PWM3 special data
register.
• PWM function can be controlled On/Off by
software.
– Enable PWM output : SET PD0
– Disable PWM output : CLR PD0
PWM 6+2 Mode
PWM 7+1 Mode
Analog to Digital Converter
• The HT46 series have a 9 or 10-bit ADC.
• ADC can be disabled by software.
• Max. 4 or 8 channels can input to the ADC.
– Channels set in ADCR by software
• ADC channels are pin-shared with Port B.
– As ADC input or Port B set in ADCR by software
•
•
•
•
•
Input range is from 0 to VDD.
Min. ADC clock period is 1us.
ADC sampling time is 32 ADC clocks.
ADC convert time is 76 ADC clocks.
Max. INL ± 1 LSB.
ADC Convert Data Register
• ADRL/ADRH are two registers to store the ADC
convert data.
A/D Convert Control Register
A/D Convert Clock Source Register
A/D Convert Timing Diagram
2
IC
Bus Interface
• I2C bus is a bidirectional
2-wire serial interface.
– SCL : serial clock pin.
– SDA : serial data pin.
• I2C output is of open
drain . An external pull
high resistor is needed.
• HT46 series I2C bus is
only operates in Slave
mode. For Master mode,
user can implement by
software.
2
IC
• I2C Slave Address
Register - HADR
• I2C Input/Output Data
Register – HDR
• I2C Control Register –
HCR.
• I2C Status Register –
HRS.
• Using HT46 serial I2C
Slave function, user can
only need to set some
flags and polling some
status flags. Then, I2C
bus can work.
Registers
Configuration Options