Download Lecture 2: Dynamic and static power in CMOS

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Electrification wikipedia , lookup

Opto-isolator wikipedia , lookup

History of electric power transmission wikipedia , lookup

Transmission line loudspeaker wikipedia , lookup

Voltage optimisation wikipedia , lookup

Buck converter wikipedia , lookup

Power engineering wikipedia , lookup

Mains electricity wikipedia , lookup

Power MOSFET wikipedia , lookup

Alternating current wikipedia , lookup

Switched-mode power supply wikipedia , lookup

CMOS wikipedia , lookup

Transcript
Low-Power Design and Test
Dynamic and Static Power in CMOS
Vishwani D. Agrawal
Srivaths Ravi
Auburn University, USA
Texas Instruments India
[email protected]
[email protected]
Hyderabad, July 30-31, 2007
http://www.eng.auburn.edu/~vagrawal/hyd.html
Copyright Agrawal & Srivaths, 2007
Low-Power Design and Test, Lecture 2
1
Components of Power
 Dynamic
 Signal transitions
 Logic activity
 Glitches
 Short-circuit
 Static
 Leakage
Copyright Agrawal & Srivaths, 2007
Ptotal =
Pdyn + Pstat
Ptran + Psc + Pstat
Low-Power Design and Test, Lecture 2
2
Power of a Transition: Ptran
Ron
VDD
ic(t)
vi (t)
vo(t)
CL
R = large
Ground
Copyright Agrawal & Srivaths, 2007
Low-Power Design and Test, Lecture 2
3
Charging of a Capacitor
R
t=0
v(t)
i(t)
C
V
Charge on capacitor, q(t)
=
C v(t)
Current, i(t)
=
C dv(t)/dt
Copyright Agrawal & Srivaths, 2007
=
dq(t)/dt
Low-Power Design and Test, Lecture 2
4
C dv(t)/dt =
[V – v(t)] /R
dv(t)
V – v(t)
───
=
─────
dt
RC
dv(t)
dt
∫ ───── = ∫ ────
V – v(t)
RC
-t
ln [V – v(t)]
=
── + A
RC
i(t)
=
Initial condition, t = 0, v(t) = 0 → A = ln V
-t
v(t) =
V [1 – exp(───)]
RC
Copyright Agrawal & Srivaths, 2007
Low-Power Design and Test, Lecture 2
5
v(t) =
i(t)
=
Copyright Agrawal & Srivaths, 2007
-t
V [1 – exp( ── )]
RC
dv(t)
C ───
dt
=
Low-Power Design and Test, Lecture 2
V
-t
── exp( ── )
R
RC
6
Total Energy Per Charging Transition
from Power Supply
Etrans =
=
Copyright Agrawal & Srivaths, 2007
∞
∫ V i(t) dt =
0
∞ V2
-t
∫ ── exp( ── ) dt
0 R
RC
CV2
Low-Power Design and Test, Lecture 2
7
Energy Dissipated per Transition in
Resistance
∞2
R ∫ i (t) dt
0
Copyright Agrawal & Srivaths, 2007
=
V2 ∞
-2t
R ──
∫ exp( ── ) dt
2
R 0
RC
=
1
─ CV2
2
Low-Power Design and Test, Lecture 2
8
Energy Stored in Charged Capacitor
∞
∞
-t
V
-t
∫ v(t) i(t) dt = ∫ V [1-exp( ── )] ─ exp( ── ) dt
0
0
RC R
RC
1
= ─ CV2
2
Copyright Agrawal & Srivaths, 2007
Low-Power Design and Test, Lecture 2
9
Transition Power
 Gate output rising transition
 Energy dissipated in pMOS transistor = CV 2/2
 Energy stored in capacitor = CV 2/2
 Gate output falling transition
 Energy dissipated in nMOS transistor = CV 2/2
 Energy dissipated per transition = CV 2/2
 Power dissipation:
Ptrans =
Etrans α fck =
α fck CV2/2
α
Copyright Agrawal & Srivaths, 2007
=
activity factor
Low-Power Design and Test, Lecture 2
10
Components of Power
 Dynamic
 Signal transitions
 Logic activity
 Glitches
 Short-circuit
 Static
 Leakage
Copyright Agrawal & Srivaths, 2007
Ptotal =
Pdyn + Pstat
Ptran + Psc + Pstat
Low-Power Design and Test, Lecture 2
11
Short Circuit Power of a Transition: Psc
VDD
vi (t)
isc(t)
vo(t)
CL
Ground
Copyright Agrawal & Srivaths, 2007
Low-Power Design and Test, Lecture 2
12
Short Circuit Current, isc(t)
VDD
VDD - VTp
Vi (t)
Volt
p-transistor
starts
conducting
n-transistor
cuts-off
Vo(t)
VTn
0
Iscmaxf
isc(t)
Isc
0
Copyright Agrawal & Srivaths, 2007
tB
tE
Low-Power Design and Test, Lecture 2
1
Time (ns)
13
Peak Short Circuit Current
 Increases with the size (or gain, β) of
transistors
 Decreases with load capacitance, CL
 Largest when CL = 0
 Reference: M. A. Ortega and J. Figueras,
“Short Circuit Power Modeling in
Submicron CMOS,” PATMOS ’96, Aug.
1996, pp. 147-166.
Copyright Agrawal & Srivaths, 2007
Low-Power Design and Test, Lecture 2
14
Short-Circuit Energy per Transition
 Escf =
=
∫tB
tE
VDD isc(t)dt
(tE – tB) Iscmaxf VDD / 2
 Escf =
tf (VDD - |VTp| - VTn) Iscmaxf / 2
 Escr =
tr (VDD - |VTp| - VTn) Iscmaxr / 2
 Escf = Escr = 0, when VDD = |VTp| + VTn
Copyright Agrawal & Srivaths, 2007
Low-Power Design and Test, Lecture 2
15
Short-Circuit Energy
 Increases with rise and fall times of input
 Decreases for larger output load capacitance
 Decreases and eventually becomes zero
when VDD is scaled down but the threshold
voltages are not scaled down
Copyright Agrawal & Srivaths, 2007
Low-Power Design and Test, Lecture 2
16
Short-Circuit Power Calculation
 Assume equal rise and fall times
 Model input-output capacitive coupling
(Miller capacitance)
 Use a spice model for transistors
 T. Sakurai and A. Newton, “Alpha-power Law
MOSFET model and Its Application to a CMOS
Inverter,” IEEE J. Solid State Circuits, vol. 25,
April 1990, pp. 584-594.
Copyright Agrawal & Srivaths, 2007
Low-Power Design and Test, Lecture 2
17
Short Circuit Power
Psc =
Copyright Agrawal & Srivaths, 2007
α fck Esc
Low-Power Design and Test, Lecture 2
18
Psc, Rise Time and Capacitance
VDD
Ron
vi (t)
tf
VDD
ic(t)+isc(t)
vo(t)
CL
R = large
Ground
Copyright Agrawal & Srivaths, 2007
vo(t)
tr
vo(t)
───
R↑
Low-Power Design and Test, Lecture 2
19
isc, Rise Time and Capacitance
Isc(t) =
-t
VDD[1- exp(─────)]
vo(t)
R↓(t) C
──── = ──────────────
R↑(t)
R↑(t)
Copyright Agrawal & Srivaths, 2007
Low-Power Design and Test, Lecture 2
20
iscmax, Rise Time and Capacitance
i
Small C
vo(t)
Large C
vo(t)
1
────
R↑(t)
iscmax
t
tf
Copyright Agrawal & Srivaths, 2007
Low-Power Design and Test, Lecture 2
21
Psc, Rise Times, Capacitance
 For given input rise and fall times short
circuit power decreases as output
capacitance increases.
 Short circuit power increases with increase
of input rise and fall times.
 Short circuit power is reduced if output
rise and fall times are smaller than the
input rise and fall times.
Copyright Agrawal & Srivaths, 2007
Low-Power Design and Test, Lecture 2
22
Summary: Short-Circuit Power
 Short-circuit power is consumed by each
transition (increases with input transition time).
 Reduction requires that gate output transition
should not be faster than the input transition
(faster gates can consume more short-circuit
power).
 Increasing the output load capacitance reduces
short-circuit power.
 Scaling down of supply voltage with respect to
threshold voltages reduces short-circuit power;
completely eliminated when VDD ≤ |Vtp|+Vtn .
Copyright Agrawal & Srivaths, 2007
Low-Power Design and Test, Lecture 2
23
Components of Power
 Dynamic
 Signal transitions
 Logic activity
 Glitches
 Short-circuit
 Static
 Leakage
Copyright Agrawal & Srivaths, 2007
Low-Power Design and Test, Lecture 2
24
Leakage Power
IG
Ground
Gate
VDD
R
Source
Drain
n+
Bulk Si (p)
Isub
IPT
IGIDL
n+
ID
nMOS Transistor
Copyright Agrawal & Srivaths, 2007
Low-Power Design and Test, Lecture 2
25
Leakage Current Components
 Subthreshold conduction, Isub
 Reverse bias pn junction conduction, ID
 Gate induced drain leakage, IGIDL due to
tunneling at the gate-drain overlap
 Drain source punchthrough, IPT due to
short channel and high drain-source
voltage
 Gate tunneling, IG through thin oxide;
may become significant with scaling
Copyright Agrawal & Srivaths, 2007
Low-Power Design and Test, Lecture 2
26
Subthreshold Current
Isub = μ0 Cox (W/L) Vt2 exp{(VGS –VTH ) / nVt }
μ0: carrier surface mobility
Cox: gate oxide capacitance per unit area
L: channel length
W: gate width
Vt = kT/q: thermal voltage
n: a technology parameter
Copyright Agrawal & Srivaths, 2007
Low-Power Design and Test, Lecture 2
27
IDS for Short Channel Device
Isub= μ0 Cox(W/L)Vt2 exp{(VGS –VTH + ηVDS)/nVt}
VDS = drain to source voltage
η: a proportionality factor
W. Nebel and J. Mermet (Editors), Low Power Design in Deep Submicron
Electronics, Springer, 1997, Section 4.1 by J. Figueras, pp. 81-104
Copyright Agrawal & Srivaths, 2007
Low-Power Design and Test, Lecture 2
28
Increased Subthreshold Leakage
Log (Drain current)
Scaled device
Ic
Isub
0 VTH’ VTH
Copyright Agrawal & Srivaths, 2007
Low-Power Design and Test, Lecture 2
Gate voltage
29
Summary: Leakage Power
 Leakage power as a fraction of the total power
increases as clock frequency drops. Turning
supply off in unused parts can save power.
 For a gate it is a small fraction of the total
power; it can be significant for very large
circuits.
 Scaling down features requires lowering the
threshold voltage, which increases leakage
power; roughly doubles with each shrinking.
 Multiple-threshold devices are used to reduce
leakage power.
Copyright Agrawal & Srivaths, 2007
Low-Power Design and Test, Lecture 2
30
Technology Scaling
 Scaling down 0.7 micron by factors 2 and 4
leads to 0.35 and 0.17 micron technologies
 Constant electric field assumed
Copyright Agrawal & Srivaths, 2007
Low-Power Design and Test, Lecture 2
31
Constant Electric Field Scaling
 B. Davari, R. H. Dennard and G. G.
Shahidi, “CMOS Scaling for High
Performance and Low Power—The Next
Ten Years,” Proc. IEEE, April 1995, pp.
595-606.
 Other forms of scaling are referred to as
constant-voltage and quasi-constantvoltage.
Copyright Agrawal & Srivaths, 2007
Low-Power Design and Test, Lecture 2
32
Bulk nMOSFET
Polysilicon
Gate
Drain
W
Source
n+
n+
L
p-type body (bulk)
SiO2
Thickness = tox
Copyright Agrawal & Srivaths, 2007
Low-Power Design and Test, Lecture 2
33
Technology Scaling
 A scaling factor (S ) reduces device dimensions as
1/S.
 Successive generations of technology have used a
scaling S = √2, doubling the number of transistors
per unit area. This produced 0.25μ, 0.18μ, 0.13μ,
90nm and 65nm technologies, continuing on to
45nm and 30nm.
 A 5% gate shrink (S = 1.05) is commonly applied
to boost speed as the process matures.
N. H. E. Weste and D. Harris, CMOS VLSI Design, Third Edition, Boston:
Pearson Addison-Wesley, 2005, Section 4.9.1.
Copyright Agrawal & Srivaths, 2007
Low-Power Design and Test, Lecture 2
34
Constant Electric Field Scaling
Device Parameter
Scaling
Length, L
1/S
Width, W
1/S
Gate oxide thickness, tox
1/S
Supply voltage, VDD
1/S
Threshold voltages, Vtn, Vtp
1/S
Substrate doping, NA
Copyright Agrawal & Srivaths, 2007
Low-Power Design and Test, Lecture 2
S
35
Constant Electric Field Scaling (Cont.)
Device Characteristic
Scaling
W / (L tox)
β
Current, Ids
β (VDD – Vt )
S
2
1/S
Resistance, R
VDD / Ids
1
Gate capacitance, C
W L / tox
1/S
Gate delay, τ
RC
1/S
Clock frequency, f
1/ τ
S
Dynamic power per gate, P
CV 2 f
Chip area, A
1/S
2
1/S
2
Power density
P/A
1
Current density
Ids /A
S
Copyright Agrawal & Srivaths, 2007
Low-Power Design and Test, Lecture 2
36
Problem: A Design Example


A battery-operated 65nm digital CMOS device is found
to consume equal amounts (P ) of dynamic power and
leakage power while the short-circuit power is
negligible. The energy consumed by a computing task,
that takes T seconds, is 2PT.
Compare two power reduction strategies for extending
the battery life:
A.
B.
Clock frequency is reduced to half, keeping all other
parameters constant.
Supply voltage is reduced to half. This slows the gates down
and forces the clock frequency to be lowered to half of its
original (full voltage) value. Assume that leakage current is
held unchanged by modifying the design of transistors.
Copyright Agrawal & Srivaths, 2007
Low-Power Design and Test, Lecture 2
37
Solution: Part A. Clock Frequency
Reduction


Reducing the clock frequency will reduce
dynamic power to P / 2, keep the static
power the same as P, and double the
execution time of the task.
Energy consumption for the task will be,
Energy = (P / 2 + P ) 2T = 3PT
which is greater than the original 2PT.
Copyright Agrawal & Srivaths, 2007
Low-Power Design and Test, Lecture 2
38
Solution: Part B. Supply Voltage
Reduction

When the supply voltage and clock frequency
are reduced to half their values, dynamic power
is reduced to P / 8 and static power to P / 2.
The time of task is doubled and the total energy
consumption is,
Energy = (P / 8 + P / 2) 2T = 5PT / 4 =1.25PT

The voltage reduction strategy reduces energy
consumption while a simple frequency reduction
consumes more energy.
Copyright Agrawal & Srivaths, 2007
Low-Power Design and Test, Lecture 2
39