Download Firmware Update for the DTR-50.1/DTR-40.1/DHC-40.1

Firmware Update for the DTR-50.1/DTR-40.1/DHC-40.1
We are pleased to offer this firmware update for the best possible performance of your AV Receiver.
The firmware update may fail if an external HDMI control signal is input during the update procedure. Please
be sure to turn off the HDMI control function (RIHD) on your A/V receiver before starting the update.
How to turn off RIHD:
In the Main menu select "7. Hardware Setup", then "7-4. HDMI".
Set "HDMI Control" to OFF.
•
Please read the update instructions carefully before beginning.
•
The firmware update should take 30 to 40 minutes. Once the update begins, don't turn off the power supply
to the A/V receiver until it is time to restart it.
•
Depending on the conditions of the network, a firmware update via a network may take more than one hour
or even fail to finish. If the update is not completed within two hours, turn off the power supply by pushing
the ON/STANDBY button and then try updating again from the beginning.
•
Updating the firmware and adjusting the settings will be done automatically, but may take some time to
complete. Please follow the procedures as instructed when you update. Note that the update may fail, or
cause problems for your A/V receiver, if you do any of the following:
• Pull out the A/V receiver’s power cord;
• Interrupt the power supply to the A/V receiver (e.g. if the breaker is tripped or if there is an electrical
outage);
• Insert or remove the LAN cable from a device in your network when updating over a network;
• Insert or remove a USB memory device from the A/V receiver when updating via USB;
• Operate components connected to the A/V receiver via HDMI, such as a TV or a recording device.
If your A/V receiver is damaged for any of the reasons above, an Integra service center will repair the unit for a
fee.
Firmware Update for the DTR-50.1/DTR-40.1/DHC-40.1
We are pleased to offer this firmware update for the best possible performance of your AV Receiver.
A firmware update is now available through the Network connection on the DTR-50.1/DTR-40.1/DHC-40.1.
The 10/21/09 update will:
1. Add New Windows 7 compatibility, adds “Play to” function for Audio streaming from PC running
Windows 7 (Oct 2009 release date).
2. Improve picture quality for iPod/iPhone through UP-A1
The 11/19/09 update will:
1. Improve sound level balance in Bi-amp mode
2. Improve update functionality
The 2/24/10 update will:
1. Enhance S/N during 24bit/96kHz content playback from USB memory/DLNA server
2. Reduce speaker relay switching sound
The latest update includes all prior updates.
We hope you enjoy the improved functionality this update provides to your AV Receiver.
Firmware Update for the DTR-40.1/50.1 and DHC-40.1
There are the following methods to update the firmware: via network and via USB storage.
Please choose either one that suits your condition. Before you start, carefully read the update
procedure.
It will take 30 to 40 minutes to update the firmware.
Update via network (DTR-40.1/50.1 and DHC-40.1)
You need a wired Internet connection to update the firmware.
For the update procedure, please refer to “Updating the Firmware via Network” on page 4.
Update via USB storage (DTR-50.1 only)
Please prepare a USB storage device such as a USB flash memory stick. You need at least 32
MB of available space to update the firmware.
For the update procedure, please refer to “Updating the Firmware via USB” on page 6.
Precautions on the USB storage device:
• The storage media in the USB card reader may not work.
• If the storage device has been partitioned, each section will be treated as an independent
device.
• If the USB mass storage device contains a lot of data, the AV receiver/controller may
take a while to read it.
• Operation with all USB mass storage devices including the ability to power them is not
guaranteed.
• Integra accepts no responsibility whatsoever for the loss or damage to data stored on a
USB mass storage device when that device is used
• with the AV receiver/controller. We recommend that you back up your important music
files beforehand.
• If you connect a USB hard disk drive to the USB port, we recommend that you use its
AC adapter to power it.
• USB hubs and USB devices with hub functions are not supported. Do not connect your
USB mass storage device via a USB hub.
• USB memory devices with security functions are not supported.
Updating the Firmware via Network
DTR-50.1/DTR-40.1/DHC-40.1 allows you to update
firmware using Network connection on rear panel.
Step 4:
Select “Via NET” and push [ENTER].
Notice:
1. Make sure your AV receiver and TV are turned on
and Ethernet cable is connected to rear panel of the AV
receiver.
2. Never unplug or turn off the AV receiver during
updating process.
3. It will take 15 to 25 minutes to update the firmware.
4. The AV receiver will retain all your settings after
update is finished.
Step 1:
Push [RECEIVER] followed by [SETUP] on the remote
controller.
Main menu will be displayed on TV screen.
Step 5:
Select “Update” and push [ENTER].
Step 2:
Go to “7. Hardware Setup” menu.
Updating will begin.
Step 3:
Go to “7-6. Firmware Update” menu.
Note that the Firmware Update option will be grayed out
for 30 seconds after AV receiver/controller is turned on.
Please wait.
Step 6:
After about 15 to 25 minutes, message
“OK:Sum = ********” appears on the front display of
the AV receiver, indicating that the update has been
completed. (Alpha-numeric characters on the front
display are denoted by asterisks.)
Step7:
Using the [ON/STANDBY] button on the front panel,
turn off and on the AV receiver.
Do not use the [ON] or [STANDBY] button on the
remote controller.
Congratulations!! Now you have the latest firmware on
your Integra AV receiver.
(Go to the next page for troubleshooting.)
Troubleshooting
Case 1:
If “No Update” is displayed on the front display of the
AV receiver/controller as below, the firmware has
already been updated. You do not need to do anything
further.
Case 2:
If an error occurs, “Error!! *-**” is displayed on the
front display of the AV receiver/controller.
(Alphanumeric characters on the front display are
denoted by asterisks.) The example below is displaying
error code 0-10. See the following table and take
appropriate action.
Errors during update via Network
Error Code
*-10, *-20
Description
Ethernet cable is not detected. Connect the cable
properly. See the instruction manual for the
network connection.
*-11, *-13,
*-21, *-28
Internet connection error. Check the following
items:
• Make sure IP address, subnet mask, gateway
address, and DNS server are configured
properly.
• Make sure the router is turned on.
• Make sure the AV receiver/controller and the
router are connected with Ethernet cable.
• Make sure the setup configuration of the router
is set properly. See the instruction manual of the
router.
• If your network allows only one client
connection and there is any other device already
connected, the AV receiver/controller cannot
access the network. Consult your Internet
Service Provider (ISP).
• If your modem does not function as a router,
you will need a router. Depending on your
network, you may need to configure the proxy
server if needed. See the document provided by
your ISP. If you still cannot access the Internet,
DNS or proxy server may be temporarily down.
Contact your ISP.
Retry the update procedure from the beginning.
If the error persists, please contact Integra
Support (indicated at the end of this page) and
provide the error code.
Others
Case 3:
If you do not have a wired connection to the network,
please contact below.
ONKYO CORPORATION
2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
The Americas
Integra Division of ONKYO U.S.A. CORPORATION
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
Tel: +1-800-225-1946, +1-201-818-9200
Hours: M-F 9am-8pm/Sat-Sun 10am-4pm ET
<http://www.integrahometheater.com/>
Europe
ONKYO EUROPE ELECTRONICS GmbH
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
Tel: +49-8142-4401-0 Fax: +49-8142-4401-555
Asia, Oceania
Please contact an ONKYO distributor referring to Onkyo SUPPORT
site.
<http://www.intl.onkyo.com/support/local_support/index.html>
Updating the Firmware via USB (DTR-50.1 only)
DTR-50.1 allows you to update firmware using a USB
storage device.
* In this procedure, on-screen display may vary depending on the
model.
Note:
1. Never unplug or turn off the AV receiver/controller
during updating process.
2. It will take 30 to 40 minutes to update the firmware.
3. The AV receiver/controller will retain all your
settings after update is finished.
Step 7:
Push [RECEIVER] followed by [SETUP] on the remote
controller.
Main menu will be displayed on TV screen.
Procedures thereafter can also be performed on the
AV receiver/controller by using its SETUP, arrow, and
ENTER buttons.
Step 8:
Go to “7. Hardware Setup” menu.
Step 1:
Connect a USB storage device to your PC. If there is any
data in the USB storage, remove it.
Download the firmware file from the Integra web site.
The file name is as follows:
ONKAVR0001_*******.zip
Extract the zip file that you have downloaded. The
following three files are created:
ONKAVR0001_*******.of1
ONKAVR0001_*******.of2
ONKAVR0001_*******.of3
Step 9:
Go to “7-6. Firmware Update” menu.
Step 3:
Copy the extracted files to the USB storage device. Be
careful not to copy the zip file.
Step 4:
Remove the USB storage device from your PC and
connect it to the USB port on the AV receiver/controller.
When the AV receiver/controller has two USB ports,
you can use either one.
Step 5:
Make sure your AV receiver/controller and TV are
turned on.
If the AV receiver/controller is in standby mode, push
[ON/STANDBY] to light up the front display.
Step 6:
Select the USB input source. “Now Initializing” is
displayed on the front display and then the name of the
USB storage device is displayed. It will take 20 to 30
seconds to recognize the USB storage device.
Step 10:
Select “Via USB” and push [ENTER].
Updating the Firmware via USB (DTR-50.1 only)
Step 11:
Select “Update” and push [ENTER].
Case 2:
If an error occurs, “Error!! *-**” is displayed on the
front display of the AV receiver/controller.
(Alphanumeric characters on the front display are
denoted by asterisks.) The example below is displaying
error code 0-10. See the following table and take
appropriate action.
Error Code
Description
Updating will begin.
As the updating progresses, the TV screen may
disappear depending on the program updated. In this
case, you can see the update progress on the front
display of the AV receiver/controller. The TV screen
will reappear when you finish the update and turn on the
AV receiver/controller.
Do not turn off the AV receiver/controller and do not
remove the USB storage device during updating
process.
*-10, *-20
USB storage device is not detected. Make sure
the USB flash memory or USB cable is
properly connected to the USB port. If the
USB storage device has its own power supply,
use it to power the USB storage device.
*-14
An update file is not found in the root folder of
the USB storage device, or an update file is for
other model. Retry download following
instructions at the support website. If the error
persists, please contact Integra Support
(indicated at the end of this page) and provide
the error code.
Step 12:
Message “OK:Sum = ********” appears on the front
display of the AV receiver/controller, indicating that the
update has been completed. (Alpha-numeric characters
on the front display are denoted by asterisks.)
Others
Step13:
Using the [ON/STANDBY] button on the front panel,
turn off the AV receiver/controller and then remove the
USB storage device.
* Do not use the [ON] or [STANDBY] button on the remote
controller.
Step1 4:
Push [ON/STANDBY] to turn on the AV
receiver/controller.
Congratulations!! Now you have the latest firmware on
your Integra AV receiver/controller.
Retry the update procedure from the
beginning. If the error persists, please contact
Integra Support (indicated at the end of this
page) and provide the error code.
Errors during update via USB
ONKYO CORPORATION
2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
The Americas
Integra Division of ONKYO U.S.A. CORPORATION
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
Tel: +1-800-225-1946, +1-201-818-9200
Hours: M-F 9am-8pm/Sat-Sun 10am-4pm ET
<http://www.integrahometheater.com/>
Europe
ONKYO EUROPE ELECTRONICS GmbH
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
Tel: +49-8142-4401-0 Fax: +49-8142-4401-555
Asia, Oceania
Please contact an ONKYO distributor referring to Onkyo
SUPPORT site.
<http://www.intl.onkyo.com/support/local_support/index.html>
Troubleshooting
Case 1:
If “No Update” is displayed on the front display of the
AV receiver/controller as below, the firmware has
already been updated. You do not need to do anything
further.