Download Stulberg Hip Positioner

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts
no text concepts found
Transcript
Stulberg Hip Positioner
Provides stable positioning of a patient during hip surgery
Designed by S. David Stulberg, MD
The Stulberg Hip Positioner is used for stable positioning of a patient during total hip
and revision surgery. It is designed to attach directly to the operating table utilizing the
existing table adapters.
The upright pads are made of semi-dense foam to help prevent pressure points and
are sealed with a washable coating. The coating also helps to lessen the possibility of
skin breakdown.
The hip positioner consists of: One 10” post assembly with double pads and one 6”
post assembly with a single pad, two 2” spacers, one 4” screw, one 6” screw, two table
attachments, and a storage case.
The spacers and longer screws are supplied for use with larger patients: use one
spacer with the 4” screw, or combine the two spacers to use with the 6” screw.
The pad assembly can be adjusted for additional height and width. The upright posts
are modular. The complete unit is radiolucent and autoclavable except for the foam pads.
Storage Case
Included
FREE TRIAL
AL ON MOST INSTRUMENTS
103 Estus Drive, Savannah, GA 31404
www.innomed.net [email protected]
912.236.0000 Phone
912.236.7766 Fax
© 2012 Innomed, Inc.
Innomed-Europe Tel
Tel. +41 41 740 67 73
Fax +41 41 740 67 74
11.800.548.2362
800
PATIENT POSITIONING
1) The patient is turned and placed with the greater trochanter of the
opposite hip resting on the center pad of the bottom plate or table pad.
2) The patient is held so that the pelvis is straight (a line across the anterior
or posterior superior iliac spines is perpendicular to the floor).
3) The posterior support post (shortest one) with the pad attached, is slid
into place against the posterior sacrum and locked. The height of the pad
should be just above the midline.
Small Pad
10” Post
Pad Knob
6” Post
4) The anterior support post is then slid into place so that the pad contacts
the anterior superior iliac spine. Ideally, the pad is placed as proximal as
possible while still supporting the anterior pelvis at the level of the spine.
This minimizes any block to flexion from the pad and post. The height of
the post and pad position are dictated by the patients anatomy.
Plate
Post Screw
5) Because some patients will still rotate inside the soft tissue envelop, the
leg to be operated can be placed over the anterior side of the table to
duplicate the position the hip would be in during the placement of the
acetabulum. (With any of the common lateral approaches, an anterior
retractor is generally used for exposure which will pull the pelvis forward.)
With the leg in this position, any forward rotation of the pelvis can be
compensated for by rolling the operating table to the posterior side until a
line across the posterior superior iliac spines is perpendicular to the floor.
It is recommended that all patients be checked to determine the amount
of forward roll that can occur.
6) To help protect the skin, a draw sheet underneath the patient can
be brought up and placed between the pads and the skin during the
positioning. Care should be taken to be sure that the pressure on the skin
areas is not excessive and that any interposed material is smooth without
local pressure points.
7) In obese patients, during the positioning, the bulk of the belly can usually
be pulled proximally and the anterior post with its pads placed across the
lower abdomen while still at the level of the anterior superior iliac spines.
8) At the conclusion of the positioning, the hip flexion is checked to be sure it
is not blocked by the position of the pads and post. Any tilting of the pelvis
and how level the operating room table is, can also he checked prior to
prepping and draping the patient and hip.
Slider Screw
Slider
Table Attachment
2" Knob
PRODUCT NO’S:
4150-00
[Stulberg Hip Positioner]
Optional & Replacement Parts:
4150-PD3
4150-PA
4150-PS
4150-SS
4150-P
4150-PB
4150-EXT
4150-EK
4150-C
4150-EXT4
4150-EK4
4150-C4
4150-S
4150-TA
4150-V
4150-06
4150-06B
4150-06C
4150-06D
4150-09
4150-10
4150-10B
4150-10C
4150-10D
4150-12
4150-14
[Small Pad Set (Set of 3)]
[Pad Assembly (Pad knob, plate & pad)]
[Post Screw (Small wingnut on post)]
[Slider Screw (Small wingnut on slider)]
[Plate (Small pad attaches to this plate)]
[2” Pad knob (Attaches pad to post)]
[2” Extension (2” spacer & 4” knob)]
[4” Extension knob (Used with 2” spacer)]
[2” Extension spacer (2” cylinder)]
[4” Extension (4” spacer & 6” knob)]
[6” Extension knob (Used with 4” spacer)]
[4” Extension spacer (4” Cylinder)]
[Slider (Connects post to baseplate)]
[Table Attachment]
[Velcro strips (Extra velcro/for 30 pads)]
[6” Post only]
[6” Post with pad assembly]
[6” Post with pad assembly and slider]
[6” Post with pad assembly, slider & table attachment]
[9” Custom post/post only]
[10” Post only]
[10” Post with pad assembly]
[10” Post with pad assembly with slider]
[10” Post with pad assembly, slider & table attachment]
[12” Custom post/post only]
[14” Custom post/post only]
4" Extension Knob
6" Extension Knob
2" Extension Spacer
4" Extension Spacer
Plate
Velcro Strips
Velcro Strips
Small Pad
Post
Slider Screw
Small
Pad
Extension
Knob
Slider
Extension
Spacer(s)
Plate
Extension
spacer
assembly.
10” Post
6” Post
Post Screw
Table
Attachment
The upright assembly can be rotated and locked in place.
The pads can be adjusted for height and width.
The upright assembly adjusts by a sliding
track to accommodate various sized
patients. It is locked in the sliding track
by tightening one or two locking bolts.
Storage Case
CLEANING AND STERILIZATION PROCEDURE
Stulberg Hip Positioner
Product No: 4150
Made of aluminum, delrin, and stainless steel. The Stulberg Hip Positioner, including the pads, does not contain any trace of latex.
Normally, this positioner is used under a drape in a non-sterile area. If you choose to sterilize it, this product
can be pre-vacuum steam sterilized wrapped or unwrapped.
Please use the following guidelines when sterilizing this product:
Sterilizer Type:
Pre-vacuum Steam Sterilizer
Minimum Temperature:
132 degrees C / 270 degrees F
Minimum Cycle Time:
6 minutes
Minimum Dry Time:
0 minutes
The pads should not be sterilized. They should be cleaned with rubbing alcohol. Steam sterilization will melt the coating
on the foam pads and will weaken adhesive on the Velcro strips. Periodic replacement of the pads is recommended when
pads become soiled or adhesive becomes weakened.
Innomed recommends that the cleaning and decontamination
of instruments follow the guidelines set forth by AORN/HIMA
and AAMI. Both physical and chemical (detergent) processes
are necessary to minimize the bioburden on all soiled items.
Chemical (detergent) cleaners alone cannot remove all soil
and debris, therefore a careful manual cleaning of each
item with a soft sponge or cloth is essential for maximum
decontamination. Carefully inspect hidden areas such as
cannulations and recesses to assure any residual materials
are removed. Once the items have been cleaned and decontaminated they should be thoroughly rinsed with clean water to
remove any detergent or chemical residue before sterilization.
Innomed recommends the use of a mild enzymatic detergent
with a low pH. Do not use multipurpose detergents to wash
or soak your instruments. Use a specifically compounded lowsuds detergent for all instruments. Detergents designed for
surgical instruments, pads and straps are specifically formulated to remove protein, organic debris and blood. The neutral
pH balance will not damage stainless steel or tungsten carbide
inserts. The solution is gentle enough for manual (hand) as
well as ultrasonic cleaning.
INSTRUMENT CARE PROCEDURE
1. Visually inspect instruments before cleaning for cracks, tears
and chipped areas.
2. Clean instruments thoroughly after use.
a. If you use a pre-soak solution; be certain that it has a neutral pH balance.
b. Clean instruments in an open position by either hand or
ultrasonic cleaner.
c. Use a non-metallic brush (toothbrush) to remove stubborn
debris. DO NOT use abrasive cleaning solutions or scouring
pads.
d. DO NOT expose instruments to bleach.
Detergents designed for surgical instruments are specifically formulated to remove protein, organic debris and blood. The neutral
pH balance will not damage stainless steel or tungsten carbide
inserts. The solution is gentle enough for manual (hand) as well as
ultrasonic cleaning.
Revised 1/1/12
FREE TRIAL ON MOST INSTRUMENTS
103 Estus Drive, Savannah, GA 31404
www.innomed.net [email protected]
912.236.0000 Phone
912.236.7766 Fax
© 2012 Innomed, Inc.
Innomed-Europe Tel. +41 41 740 67 73
Fax +41 41 740 67 74
1.800.548.2362