Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Ultem® 2300 PEI, Polyetherimide, 30% glass reinforced, extruded MECHANICAL PROPERTIES Specific Gravity Tensile Strength, psi Tensile Modulus, psi Elongation, % Flexural Strength, psi Flexural Modulus, psi Compressive Strength, psi Compressive Modulus, psi Hardness, Rockwell M Hardness, Rockwell R Hardness, Durometer, Shore D Scale Izod Impact (Notched), ft-lb/in Relative Machinability THERMAL PROPERTIES Coefficient of Thermal Expansion, 10E-4/°F Deflection Temperature 264 psi, ºF Tg-Glass Transition (Amorphous), ºF Continuous Service in Air (Max), °F Thermal Conductivity, BTU-in/hr-ft²-°F ELECTRICAL PROPERTIES Dielectric Strength, Short Term, Volts/mil Surface Resistance, Ohm/Square Dielectric Constant, 1 MHz Dissipation Factor, 1 MHz CHEMICAL PROPERTIES Water Absorption Immersion, 24 hr., % Water Absorption Immersion Sat, % Acids, Weak (acetic, dilute HCl) Acids, Strong (conc. HCl or sulfuric) Alkalies, Weak (dilute NaOH) Alkalies, Strong (conc. NaOH) Hydrocarbons, Aromatic (toluene) Hydrocarbons, Aliphatic (gasoline) Ketones, Esters (acetone) Ethers (diethyl ether, THF) Chlorinated Solvents (methylene chloride) Alcohols (methanol, anti-freeze) Continuous Sunlight COMPLIANCE Flammability, UL94 (5=V-0; 4=V-1; 3=V-2; 1=HB) FDA (1=Yes) ENGLISH VALUESCOMMENTS 1.51 ASTM D792 17000 ASTM D638 800000 ASTM D638 3 ASTM D638 27000 ASTM D790 850000 ASTM D790 32000 ASTM D695, 10% Def. 625000 ASTM D695 114 ASTM D785 127 ASTM D785 86 ASTM D2240 1 ASTM D256 Type A 7 1-10, 1=Easier to Machine ENGLISH VALUESCOMMENTS 0.11 ASTM E831 (-40°F to 300°F) 410 ASTM D648 410 ASTM D3418 340 Long Term 1.56 ASTM F433 VALUES COMMENTS 770 ASTM D149 1E+13 Lower Limit; EOS/ESD S11.11 3.7 ASTM D150 0.0015 ASTM D150 ENGLISH VALUESCOMMENTS 0.18 ASTM D570(2) 0.9 ASTM D570(2) 3 Acceptable Service 1 Unacceptable 3 Acceptable Service 1 Unacceptable 1 Unacceptable 2 Limited Service 1 Unacceptable 3 Acceptable Service 1 Unacceptable 3 Acceptable Service 3 Acceptable Service ENGLISH VALUESCOMMENTS 5 (V-0) UL94; 1/8 inch 0 Not Compliant METRIC VALUES 1.51 117 MPa 5,516 MPa 3% 186 MPa 5,861 MPa 221 MPa 4,309 MPa 114 127 86 53 J/m 7 METRIC VALUES 0.20 10-4/K 210 °C 210 °C 171 °C 0.22 W/m-K METRIC VALUES 30 kV/mm 1E+13 Ohm/Square 3.7 0.0015 METRIC VALUES 0.18 % 0.9 % 3 1 3 1 1 2 1 3 1 3 3 METRIC VALUES 5 0 IMPORTANT: The information contained herein is believed to be reliable, but no representations, guarantees or warranties of any kind are made as to its accuracy, suitability for particular applications or the results to be obtained therefrom. Lehigh Valley Plastics, Inc. will not be held responsible for the use of this information relative to actual application. LEHIGH VALLEY PLASTICS, INC. 187 North Commerce Way, Bethlehem, PA 18017 USA www.lehighvalleyplastics.com