Download How To Easily Make Your Own UC3842 PWM IC Tester

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Power inverter wikipedia , lookup

Power factor wikipedia , lookup

History of electric power transmission wikipedia , lookup

Standby power wikipedia , lookup

Wireless power transfer wikipedia , lookup

Mains electricity wikipedia , lookup

Alternating current wikipedia , lookup

Amtrak's 25 Hz traction power system wikipedia , lookup

Electric power system wikipedia , lookup

Audio power wikipedia , lookup

Electrification wikipedia , lookup

Power over Ethernet wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Power engineering wikipedia , lookup

AC adapter wikipedia , lookup

Pulse-width modulation wikipedia , lookup

Transcript
How To Easily Make Your Own UC3842
PWM IC Tester
If you have been repairing switch mode power supplies (SMPS), I’m sure
you have definitely come across the famous UC3842 Pulse Width
Modulation (PWM) IC. This IC generates a pulse waveform to switch the
Power Mosfet Transistor. Whenever a SMPS have problem one of the
component that we directly replaced was the UC3842 IC. The reason we
directly replace the IC is because we can’t test the power IC with meter.
Although there were some suggestion saying that one could test the power
IC by measuring the internal transistor at pin 5, 6 and 7 but many times the
internal transistor were tested good and yet failed when the IC was in the
circuit. Due to this I did not use the above method to test on the UC3842 IC.
Do you know that we could have wasted lots of money simply by replacing
the power IC without knowing it whether it has problem or not. Many repair
technicians will not use back the power IC whenever they found problem
like a shorted power FET in the power primary side. The reason for it was
the original power IC could blow up the new replacement of the power FET
thus they directly replaces it. This is very true but in actual SMPS repair, not
necessary the power IC will breakdown when found that the power FET
already shorted.
Now with the help of this simple UC3842 IC Tester, you can test whether
the IC is good or bad. I got this project from a member and have redrawn the
diagram for easy fixing. Here are the part lists of this project:
Diagram of the UC3842 PWM IC Tester
1) 1 X 12V-0-12V linear transformer
2) 1 X 8 pins IC socket
3) 1 X 390 ohm ½ watt resistor
4) 1 X 4.7 K ohm potentiometer (pot)
5) 2 X 1N4007 diode
6) 1 X 47 microfarad 63 Volt capacitor
7) 1 X power switch
8) 1 X 3 pin plug
9) 1 X 3 feet power cable
10) 1X LED
11) 2 X Grommets (optional)
12) 1 X PCB Board
Here are the photos of the project
Testing Time
Just insert any PWM IC to the IC socket and power on. Whenever you
turn the pot and the LED light changes accordingly then the IC is good
(please read the tester disadvantages) and if there is no light the power IC
is bad.
Advantages:
1) Cheap and easy to build
2) Could test on UC3842, UC3843, UC3844, KA3882, KA3883,
KA3884 PWM IC’s
3) Easy observation-LED light could indicate if the IC is good or bad
4) Easy to insert and remove IC under test (with the help of the IC
socket)
Disadvantages:
1) Not 100% accurate because this circuit did not build to fully support
all the necessary circuitry. Observe that pin1 to pin 4 have no connection
where else in actual SMPS circuitry all these 4 pins are connected to
circuit. Let’s put this in a simple term: If the LED did not light up then
you are 100% sure the power IC have problem and need replacement. If
it is tested good and after putting back the IC to the SMPS and still the
power did not come up, the best is direct replacement.
This explanation is same as when you use a flyback tester. If there is no
LED lit when checking on the primary winding of the flyback
transformer you are guaranteed that the winding had shorted. If all the
LED lit and yet the flyback still would not work- then direct replace the
flyback and retest again. Flyback could breakdown when under full
operating voltage similarly the power IC could breakdown when under
full test in the SMPS circuit.
2) It can’t support other types of part number power IC other then the one
listed above.
Conclusion- Although this tester is not 100% accurate at least the
accuracy is still better when comparing with the method of checking the
power IC internal transistor as mentioned in the first paragraph. Just
imagine now you found a shorted power FET; you can easily test out
the UC3842 IC whether it is good or bad in no time. If it is bad then
get a new power IC-simple isn’t it? If it is good (although not 100%)
at least you will know that it won’t blow the new power FET again
upon power on. Build one now and look forward to save your
troubleshooting and repairing time
http://electronicrepair.weebly.com/components-testers.html