Download Switching Power Supply S82K

Switching Power Supply
S82K
DIN-Rail Mount Power Supply With
Capacity Up to 240 W for General or
Industrial Applications
Wide power range: 15 to 240 W
15 W and PFC Models with Universal
voltage of 100 to 230 VAC
120/240 Selectable on Non-PFC Models
30, 50, 100 and 240 W
Meets EN61000-3-2 (limits for harmonic
current emissions) with PFC on 240 W
T-type models with undervoltage
detection function are available:
• 15-, 30-, and 50-W:
Undervoltage detection indicator
• 100- and 240-W:
Undervoltage detection indicator and output
Conforms to UL, CSA, VDE, and CE
Safety Standards
3-year warranty
Ordering Information
SWITCHING POWER SUPPLIES
Functional configuration
Rated input voltage
Power ratings
Output voltage
Output current
Part number
100 -- 240 VAC
15 W
5V
2.5 A
S82K-01505
12 V
1.2 A
S82K-01512
24 V
0.6 A
S82K-01524
12 V
2.5 A
S82K-03012
Non-PFC
Standard
120/240
0/ 0 VAC
C selectable
se ec ab e
Undervoltage
U
de o age de
detection
ec o indicator
d ca o
100
00 -- 240
0 VAC
C
120/240
0/ 0 VAC
C selectable
se ec ab e
Undervoltage
g detection indicator
and
d output
t t
30 W
24 V
1.3 A
S82K-03024
50 W
24 V
2.1 A
S82K-05024
100 W
24 V
4.2 A
S82K-10024
240 W
24 V
10 A
S82K-24024
15 W
5V
2.5 A
S82K-01505T
12 V
1.2 A
S82K-01512T
24 V
0.6 A
S82K-01524T
12 V
2.5 A
S82K-03012T
30 W
24 V
1.3 A
S82K-03024T
50 W
24 V
2.1 A
S82K-05024T
100 W
24 V
4.2 A
S82K-10024T
240 W
24 V
10 A
S82K-24024T
240 W
24 V
10 A
S82K-P24024
With PFC
100 -- 240 VAC
S82K
S82K
MODEL NUMBER LEGEND
S82K 1
2
3
1. Power Factor Correction
None: No
P:
Yes
4
3. Output Voltage
05: 5 V
12: 12 V
24: 24 V
2. Power Ratings
015: 5 W
030: 30 W
050: 50 W
100: 100 W
240: 240 W
4. Additional Functions
None: Standard type
T:
With undervoltage detection
indicator (15-/30-/50-W) With
undervoltage detection indicator
and output (100-/240-W)
ACCESSORIES (SOLD SEPARATELY)
Description
Length
Width
Part number
DIN-rail ((See Dimensions section for details.))
0.5 m (1.64 ft)
7.3 mm (0.29 in)
PFP-50N
1 m (3.28 ft)
7.3 mm (0.29 in)
PFP-100N
1 m (3.28 ft)
16 mm (0.63 in)
PFP-100N2
Specifications
Item
e
PFC
No
Yes
Power rating
15 W
30 W
50 W
100 W
240 W
Efficiency (typical)
66% to 84% (depends on the model)
Life expectancy
8 yrs. min. (with standard installation at 40°C at the rated input with a 50% load)
240 W
Input
Voltage
100 to 240
VAC (85 to
264 VAC)
Frequency
47 to 450 Hz
Current
(S Note
(See
N t 1.)
1)
120 VAC (85 to 132 VAC) or 240 VAC (170 to 264 120 VAC (85
VAC) selectable
to 132 VAC) or
240 VAC (170
to 253 VAC)
selectable
100 to
230 VAC (85
to 253 VAC)
47 to 63 Hz
100-V input
0.45 A max.
0.9 A max.
1.3 A max.
2.5 A max.
5.5 A max.
4 A max.
200-V input
(230-V input)
0.25 A max.
0.6 A max.
0.8 A max.
1.5 A max.
3.5 A max.
(3.2 A max.)
2 A max.
(1.4 A max.)
Power factor
---
0.95 min.
Leakage current
(See Note 1.)
100-V input
0.5 mA max.
200-V input
1 mA max.
Inrush
us cu
current
e
(
(see
Note
N t 1.)
1)
100-V input
15 A max.
25 A max.
200-V input
30 A max.
50 A max.
Noise filter
Yes
Output (See Note 2.)
Voltage adjustment range
±10% (adjustable with variable resistor (V.ADJ))
Ripple (See Note 1.)
2% (p-p) max.
Input variation influence
0.5 % max. (at 85 to 132 VAC/170 to 264 VAC input, 100% load)
Load variation influence
1.5% max. (with rated input, 10 to 100% load)
Temperature variation
influence
0.05%/°C max. (with rated I/O at an ambient temperature range between 0°C to 50°C)
Rise time
100 ms max. (up to 90% of output voltage at
rated input and output)
Hold time (See Note 1.)
20 ms min.
(This table continues on the next page.)
Note: 1. Defined with a 100% load and the rated input voltage (100 or 200 VAC).
2. The output specification is defined at the power supply output terminals.
200 ms max.
0.5 % max. (at 85 to
132 VAC/170 to 253 VAC input,
100% load)
300 ms max.
1000 ms max.
S82K
S82K
Specifications Table -- continued from previous page
PFC
Item
No
Power rating
Yes
15 W
30 W
50 W
100 W
240 W
240 W
Additional function
Overload protection
105% to 160% of rated load current (typical), inverted L drop type, automatic reset
Overvoltage protection
No, except the S82K-
Undervoltage detection indicator
(DC LOW indicator)
The S82K-
Undervoltage detection output
(DC LOW output)
---
S82K10024T
model only
Parallel operation
Impossible
Possible (2 units max.)
T (shut-off type with an input resetting method)
T models only (color: red)
S82K24024T
model only
---
Characteristics
Ambient temperature
Ambient humidityy
Operating
See the derating curve in the Engineering Data section
Storage
--25°C to 65°C (--13°F to 149°F)
Operating
25% to 85%
Storage
25% to 90%
Dielectric strength
3,000 VAC at 50/60 Hz for 1 min. (between all inputs and outputs)
2,000 VAC at 50/60 Hz for 1 min. (between all inputs and GR terminal)
1,000 VAC at 50/60 Hz for 1 min. (between all outputs and GR terminal)
Insulation resistance
100 MΩ min. at 500 VDC (between all outputs and all inputs/GR terminal)
Vibration resistance
Malfunction: 10 to 55 Hz, 0.375-mm single amplitude for 2 hrs each in X, Y, and Malfunction:
Z directions
10 to 55 Hz,
0.15-mm
single amplitude for 2 hrs
each in X, Y,
and Z directions
Shock resistance
Malfunction: 294 m/s2 (approx. 30G), 3 times each in ±X, ±Y, and ±Z directions
Output indicator
Yes (green)
Electromagnetic interference
(See Note 1.)
Conforms to FCC class B
Limits for harmonic current emission
---
EMC
Emission Enclosure:
Emission AC Mains:
Immunity ESD:
EMC standards
Conforms to EN50081-2 and EN50082-2
Approved standards
UL 508, CSA C22.2 No.14, UL1012, CSA E.B1402C
VDE0160, VDE0805, EN60950 (IEC 950)
Conforms to VDE0106/P100 and CE
Weight
260 g max.
Conforms to FCC class A
Conforms to
EN61000-3-2,
IEC1000-3-2
EN55011 Group 1 class A
EN55011 Group 1 class A
EN61000-4-2: 4 kV contact discharge (level 2)
8 kV air discharge (level 3)
Immunity RF-interference:
ENV50140: 10 V/m (10 k to 1 GHz) (level 3)
Immunity Conducted Disturbance: ENV50141: 10 V (0.15 to 80 MHz) (level 3)
Immunity Burst:
EN61000-4-4: 2 kV power-line (level 3)
2 kV I/O signal-line (level 4)
380 g max.
480 g max.
Conforms to
EN50081-2
and
EN50082-2
(See Note 3.)
600 g max.
Note: 1. Defined with a 100% load and the rated input voltage (100 or 200 VAC).
2. The output specification is defined at the power supply output terminals.
3. To ensure the Emission Enclosure rating, a ferrite ring core should be used on all cables.
1800 g max.
2200 g max.
S82K
S82K
Engineering Data
DERATING CURVE
Note: The derating curve depends on the mounting position of the Power Supply.
15-/30-/50-/100-W Models
Installation A
Load (%)
Installation B
Ambient temperature (°C)
240-W Model
Load (%)
P24024:
100-V input
(see note)
Parallel-Unit Operation
Load (%)
Single-Unit Operation
Top
Ambient temperature (°C)
Note:
Ambient temperature (°C)
100-V input: 85 to 132 VAC
Note:
Mounting Position
(A) Standard (Vertical) Installation
Top
(B) Horizontal Installation
Note: Not permitted for 240-W models.
Top
Provide a clearance of at least 10 mm between Units when installing
them in horizontal series. Installing them in vertical series is not allowed.
Follow the standard mounting directions.
S82K
S82K
INRUSH CURRENT, RISE TIME, HOLD TIME
Input ON
Input OFF
AC input voltage
Inrush current on input application
AC input current
96.5%
90%
Output voltage
Rise time: 100 to 1000 ms max.
depending on the model.
OVERLOAD PROTECTION
The Power Supply is provided with an overload protection
function that protects the load and the power supply from
possible damage by overcurrent. When the output current rises
above a set value (105% of the rated output current), the
protection function is triggered, decreasing the output voltage.
When the output current falls within the rated range, the overload
protection function is automatically cleared.
Hold time
20 ms min.
OVERVOLTAGE PROTECTION
(S82K-T MODELS ONLY)
The Power Supply is provided with an overvoltage protection
function that protects the load and the Power Supply from
possible damage by overvoltage. When the output voltage rises
above a set value, the protection function is triggered, shutting off
the output voltage. If this occurs, reset the Power Supply by
turning it off for 1 minute min. and then turning it on again.
Output voltage (V)
Rated voltage
Output voltage (V)
Approx.
20%
Output current (%)
Note:
Overvoltage
protection
operating
To avoid damage to (or deterioration of) the S82K
circuitry, do not short-circuit the output terminals of the
S82K or use the S82K with excessive output current for a
long time.
10%
Rated output
voltage
--10%
Variable range
S82K
S82K
Nomenclature
S82K-100
S82K-015 S82K-030/
S82K-050
1
1
8
5
7
5
7
5
7
6
6
6
2
2
3
S82K-24024
8
1
2
3 4
3
4
1
5
7
6
2
3
1.
2.
3.
4.
5.
6.
9
4
DC output terminals -- Connect the load lines to these terminals.
Input terminals -- Connect the input lines to these terminals.
Ground terminal (GR) -- Connect a ground line to this terminal.
Input voltage selector terminals -- Selects a 100 V or 200 V input voltage.
Output indicator (DC ON) -- Lights while a Direct Current (DC) output is ON.
Output voltage adjuster (V.ADJ) -- It is possible to increase or decrease the
output voltage.
7. Undervoltage detection indicator (DC LOW) -- S82K-T only.
8. Undervoltage detection output (DC LOW) -- 100- and 240-W S82K-100T
models only.
9. Parallel/single operation selector -- Set to “PARALLEL” for parallel operation.
S82K
S82K
Operation
MODELS WITH UNDERVOLTAGE DETECTION INDICATOR AND OUTPUT FUNCTION
(S82K-T ONLY)
If the output voltage at the output terminal drops to 75% to 90% of the rated voltage, the red indicator of the S82KT (DC LOW
indicator) will be lit. In the case of the S82K-10024T/24024T, a voltage drop alarm will be output via the relay available in the models (DC
LOW output).
Note:
This function detects the voltage at the output terminal of the Power Supply. To check the precise output voltage, measure the voltage
at the load terminal.
Indicator
Voltage
Green:
DC ON
Red:
DC LOW
Green:
DC ON
If the voltage at the output terminal is more than 90%
of the rated voltage, the green indicator will be lit.
(see note 1)
Red:
DC LOW
Green:
DC ON
Red:
DC LOW
Operation of 10024T/ 24024T’s output
(DC LOW output)
(See Note 2.)
If the voltage at the output terminal is 75% to 90%,
the red indicator will be lit.
If the voltage at the output terminal is 0 V, both the
green and red indicators will not be lit.
Note: 1. The more the voltage at the output terminal drops, the darker both the green and red indicators will be.
2. The relay contacts have a capacity of 0.1 A at 24 VDC.
BLOCK DIAGRAMS
S82K-015
(15 W)
Fuse (3 A)
AC (L)
INPUT
Noise filter
AC (N)
+V
DC
OUTPUT
-- V
Inrush current Rectifier
protection circuit
GR
Photocoupler
Overload
detection circuit
Undervoltage
detection
indicator
Rectifier
Drive control
circuit
Detector
(see note)
Overvoltage
detection circuit
Overvoltage protection circuitry (see note)
Note:
T only.
The overvoltage protection circuitry and undervoltage detection indicator are available in the S82K-015
S82K
S82K
S82K-030
S82K-050
(30 W)
(50 W)
Fuse (3 A)
AC (L)
INPUT
Noise filter
AC (N)
Inrush current
Rectifier
protection circuit
100 or 200 V
(selectable)
Undervoltage
detection
indicator
Rectifier
Drive control
circuit
(See Note 2.)
GR
Detector
(See Note 1.)
Photocoupler
Overload
detection circuit
+V
DC
OUTPUT
-- V
Overvoltage
detection circuit
Overvoltage protection circuitry (See Note 1.)
Note: 1. The overvoltage protection circuitry and undervoltage detection indicator are available in the S82K-0
T only.
2. Use the short bar to short-circuit terminals 4 and 5 to select 100 to 120 VAC and remove the short bar to select 200 to 240
VAC.
(100 W)
(240 W)
S82K-100
S82K-24024
Fuse (5 A)
AC (L)
INPUT
Noise filter
AC (N)
Inrush current
Rectifier
protection circuit
100 or 200 V
(selectable)
Rectifying and
smoothing circuit
Drive control
circuit
(See Note 2.)
+V
DC
OUTPUT
-- V
Detector
GR
DC LOW
Photocoupler
Overload
detection circuit
Overvoltage
detection circuit
Undervoltage
detection
indicator/output
(See Note 1.)
Overvoltage protection circuitry (see note)
Note: 1. The overvoltage protection circuitry and undervoltage detection indicator are available in the S82KT only.
2. Use the short bar to short-circuit terminals 4 and 5 to select 100 to 120 VAC and remove the short bar to select 200 to 240
VAC (100 W), 200 to 230 W (240 W).
S82K-P24024 (240 W)
Fuse (8 A)
AC (L)
INPUT
+V
DC
OUTPUT
Noise filter
AC (N)
Inrush current
protection circuit
Rectifier
Harmonic current Smoothing
emission control
Rectifying and
smoothing circuit
Drive control
circuit
Overload
detection circuit
GR
Detector
-- V
S82K
S82K
SELECTION OF 100 TO 120 OR 200
TO 240 VAC INPUT VOLTAGE
Select a 120 V or 240 V input by shorting or opening the
Input Voltage Selector Terminals, as shown in the
following diagram (All models except for 15-W and
240-W models with PFC).
GENERATING OUTPUT VOLTAGE (±)
An output of ± can be generated by using two Power Supplies as
shown below, because the Power Supply produces a floating output.
When connecting the Power Supplies in series with an operation
amplifier, connect diodes to the output terminals as shown by the
dotted lines in the figure. No diodes are required with S82K
100-W/240-W models.
100 to 120 V Input
+V
INPUT
--V
Use the short bar to short-circuit
terminals 4 and 5.
+V
INPUT
--V
200 to 240 V Input
PARALLEL OPERATION
S82K 100-W/240-W models can be operated in parallel.
Remove the short bar.
100- and 240-W Models
+V
SERIES OPERATION
INPUT
Load
--V
S82K 100-W/240-W model can be operated in series.
+V
100-W/240-W Model
INPUT
--V
+V
INPUT
--V
Note: When operating the 240-W model in
parallel operation, set the switch to
PARALLEL. Refer to the derating
curve for the rated current under
this operation.
+V
INPUT
--V
15-, 30-, and 50-W Models
+V
INPUT
15-, 30-, 50-W Models
+V
INPUT
--V
+V
INPUT
--V
Load
--V
+V
INPUT
--V
Parallel Operation Precautions
• The length and thickness of each wire connected to the load must
be the same so that there is no difference in voltage drop value
between the load and the output terminals of each Power Supply.
• Adjust the output voltage of each Power Supply so that there will be
no difference in output voltage between each Power Supply.
• If the 240-W Power Supply is used in single operation under the
parallel operation setting, the overcurrent protection will be
actuated at an output of 90% to 95% (in current), and will not allow a
100% output.
S82K
S82K
Dimensions
Unit: mm (inch)
SWITCHING POWER SUPPLIES
S82K-015
45 (1.77)
9.8 8.3
7.5
75
(2.95)
45
35
58.1
5
91
96 (3.78)
4.6
M3.5 with square
(sliding 7 max.) washer
Mounting Holes
Two, M4 or 4.5-dia. mounting holes
60
35
S82K-030
S82K-050
90 (3.54)
80
8.3
9.8
Four, 4.5 dia.
7.5
58.1
60
35.3
45
75
(2.95)
M3.5 with square washer
4
(sliding 7 max.)
M3.5 terminal screw
Short bar
Mounting Holes
Four, M4 or 4.5-dia. mounting holes
60 (2.36)
80 (3.15)
91
96 (3.78)
5
S82K
S82K
S82K-100
145 (5.71)
Four, 4.5 dia.
135
9.8
7.5
8.3
45
58.1
35.2
60
75
(2.95)
5
91
M3.5 terminal screw
M3.5 with square washer
4
(sliding 7 max.)
96 (3.78)
Short bar
Mounting Holes
Four, M4 or 4.5-dia. mounting holes
60 (2.36)
135 (5.31)
S82K- 24024
280 (11.02)
270 (10.63)
9.8 (0.39)
8.3 (0.33)
7.8 (0.31)
Four, 4.5 dia.
27.5
(1.08)
112.8
(4.44)
130
(5.12)
4
35
(1.38)
100
(3.94)
(sliding 8 max.)
M3.5 with square washer
M3.5 terminal screw
115 (4.53)
Short bar
Mounting Holes
270 (10.63)
115
(4.53)
Four, M4 or 4.5-dia. mounting holes
130
(5.12)
4.2
(0.17)
S82K
S82K
Unit: mm (inch)
DIN-RAIL MOUNTING TRACK
PFP-100N/PFP-50N
PFP-100N2
12, 25 x 4.5 oblong
16
7.3±0.15
4.5
4.5
35
15
25
25
10
Note:
25
25
10
1,000 (500)
(See Note.)
15 (5)
(See Note.)
35±0.3
27
1
15
25
25
25
10
25 15
10
27
24
29.2
1
1.5
1,000
The values shown in parentheses are for the PFP-50N.
Precautions
MOUNTING
To Remove
To improve and maintain the reliability of the Power Supply over a
long period of time, consider the heat dissipation that takes
place.
•
•
•
To remove the Power Supply, pull down portion (C) with a
flat-blade screwdriver and pull out the Power Supply.
The Power Supply is designed to radiate heat by means of
natural air-flow. Mount the Power Supply so that air flow
takes place around the Power Supply.
When mounting two or more Power Supplies side-by-side,
allow at least 20 mm (0.79 in.) spacing between them, as
shown in the following illustration.
Omron recommends forced-air cooling.
To DIN-Rail Mount the Power Supply
To mount the Power Supply on a DIN rail, hook portion (A) of the
Power Supply to the rail and press the Power Supply toward
direction (B).
(A)
(B)
20 mm min.
Air
30 mm
min.
(C)
Rail stopper
S82K
S82K
NOTE: DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters to inches divide by 25.4.
OMRON
ELECTRONICS,
INC.tel:+31 23 5681390, fax:+31 23 5681397, http://www.eu.omron.com/ema
OMRON CANADA, INC.
Omron Europe
B.V. EMA-ISD,
One East Commerce Drive
Schaumburg, IL 60173
885 Milner Avenue
Scarborough, Ontario M1B 5V8
1-800-55-OMRON
416-286-6465
Cat. No. GC PS4
3/98
Specifications subject to change without notice.
Printed in U.S.A.