Download Backing Up Epson Toyocom Real-Time Clock Chips

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Power over Ethernet wikipedia , lookup

Printed circuit board wikipedia , lookup

Power engineering wikipedia , lookup

Alternating current wikipedia , lookup

Time-to-digital converter wikipedia , lookup

Amtrak's 25 Hz traction power system wikipedia , lookup

Mains electricity wikipedia , lookup

Charging station wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Rectiverter wikipedia , lookup

Electric battery wikipedia , lookup

Buck converter wikipedia , lookup

Transcript
AN-1006
Application Note
Backing Up Epson Toyocom Real-Time Clock Chips
A Demonstration Tool for Cymbet™ EnerChip™
Solid State Thin Film Rechargeable Batteries
is fully charged. At full charge, the current is in the sub-nanoamps. A
simple but effective technique prevents the battery from discharging
through the charging circuit or the power supply during primary
power outages.
The Cypress USB-to-I2C converter board was chosen to provide a
cost effective way of programming the Epson RTC-8564 JE real time
clock chip and to use the display and operating system of a notebook
computer to provide a graphical user interface (GUI). The board also
provides a convenient way to power the clock chip and charge the
Cymbet solid state battery.
To charge the battery, operate the system with the Demo Board
connected for at least 30 minutes. The battery will be charged to 80%
within 30 minutes and to 100% after 45 minutes. Please see AN-1003
for details on battery charging times.
Figure 1. Cymbet Demo Kit for Epson Toyocom RTC chips.
Introduction
Cymbet™ EnerChip™ solid state, thin film batteries are ideal
as rechargeable backup power sources for real-time clock
(RTC) chips, memories, microcontrollers and other low-power
circuits where data or timing information must be retained in
the absence of primary power. They come in standard
integrated circuit packages and can be reflow soldered for high
volume PCB assembly.
This application note describes a test/demo kit and test procedures which allows a user to evaluate Cymbet batteries as a
backup for Epson Toyocom RTC chips. This system consists
of the following items:
System Operation
Overview
The demo system utilizes a Microsoft Windows™ based computer
with a USB interface. Upon connection, the RTC Demo Board will
have its time set or read via the computer. The Board will then be
disconnected from the USB-to-I2C converter, and the GUI will blank
the time display digits. When the Demo Board is again connected to
USB-to-I2C converter, the correct updated time will be shown by the
GUI since the RTC module has been powered by the Cymbet battery.
Installing the Software
1. Cymbet Epson RTC Demo Board (upper right in Figure
1). Includes a Cymbet CBC050 50-µAh battery, a Cymbet
CBC012 12-µAh battery, the same battery charging circuit
as Cymbet’s EVAL-01 board, and an Epson Toyocom
RTC-8564 JE real-time clock chip.
Open the .zip file and copy the contents into a directory on your
computer. The files should include PSoCfirstTouchUSBNetLib.dll,
RTCDemo.exe and logo1.bmp. The software will not work if installed
on a network drive. To start the GUI, click on the RTCDemo icon. If
there is a warning, go to the Microsoft website, download the .net
Framework update, and install
http://www.microsoft.com/downloads/Search.aspx?displaylang=en
2. CD ROM with Cymbet software.
Running the System
2
3. Cypress Semiconductor USB-to-I C Bridge Kit, CY3240I2USB. Includes a USB-to-I2C converter board (upper left
in Figure 1) and a USB cable. Cypress kit or equivalent to
be furnished by user.
The Cymbet Epson RTC Demo Board uses the Cymbet
EVAL-01 circuit to charge an on-board Cymbet battery at a
constant voltage. Please see AN-1003 for details. As the
battery is charging, the charging current drops until the battery
Caution: to minimize the possibility of damaging the demo system,
make sure power is off whenever separating or mating the Demo
Board with the USB-to-I2C converter. Do this by turning off the RTC
power button in the GUI, or disconnect the USB connector at the
personal computer or USB-to-I2C converter board.
© Cymbet Corporation • 18326 Joplin Street, Elk River, MN 55330 • 763-633-1780 • www.cymbet.com
DOC-111006 RevA
Page 1
AN-1006: Backing Up Epson Real-Time Clock Chips
GUI Description
The graphical user interface (GUI) is shown in Figure 2. The
GUI has fields to display hours, minutes and seconds, status of
the low voltage indicator of the Epson RTC module, and status
of the USB link. The GUI also provides fields to turn power on
and off to the Demo Board and to set the time.
6) Turn off RTC Power and separate the Cymbet Demo Board
from the USB-to-I2C converter board.
7) Verify that RTC power is off, as indicated by the GUI, then
connect the Demo Board to the USB-to-I2C converter.
8) Turn on the RTC Power button in the GUI and note that the
correct indicated time is still being displayed.
9) If the EnerChip cell is depleted, the VL indicator (voltage low)
will be displayed in the GUI. In this case, then the operation of
the Epson RTC module is in an unknown state and indications
are not valid. To clear the VL indicator, set a new time. The
VL indicator can be forced to activate by pulling the BAT
ENB shunt jumper J3 (see Figure 3) from the backside of the
Demo Board and then turning off the RTC Power button.
Performance
Figure 2. Graphical User Interface (GUI).
The Epson RTC-8564 JE real time clock module has a typical
current draw of 310 nA at 4V. As shown in Figure 4, it will
run continuously 42 hours when powered by a 12 µAh Cymbet
thin film battery and for 7 days when powered by 50 µAh
battery.
Normal operation
5
1) Connect shunt jumper J3 to the two pins on the bottom of the
Cymbet Epson RTC demo board. This jumper enables the
Cymbet cell to provide backup power to the Epson RTC-8564
JE real time clock module.
Cell Voltage
4
3
2
I2 µAh
1
50 µAh
0
Figure 3. Connection of Cypress and Cymbet boards.
0
1
2
3
4
5
6
7
8
Days
2) Connect the Cypress USB-to-I2C converter to the Cymbet
Demo Board as shown in Figure 3.
3) Connect the USB cable between the PC and USB-to-I2C
converter board.
Figure 4. Battery voltage applied to RTC.
4) Power up the computer if not already done and open the GUI
by clicking on the RTCdemo icon.
5) Verify that USB status is connected. Set RTC power to on. Set
appropriate time if needed. Note: when the GUI is first run it
will pick up the system time and put it into the set time field at
the bottom of the GUI. If it will be a more than a few minutes
before the time will be set into the Epson RTC-8564 JE real
time clock module it may be faster to restart the GUI instead
of using the up and down arrows to set the time in the set time
field.
© Cymbet Corporation • 18326 Joplin Street, Elk River, MN 55330 • 763-633-1780 • www.cymbet.com
DOC-111006 RevA
Page 2
AN-1006: Backing Up Epson Real-Time Clock Chips
R9 470
R1
200K
R2
200K
R3
200K
D4
SML-LX0603IW-TR
J1
U3
1
2
3
4
5
10
INT
6
7
3
I2C
5
CLKOUT
SCL
VDD
SDA
(GND)
CLKOE
4
C1
8
0.1uF
9
GND
RTC-8564 JE
R6
10K
2
R4
6.8K
MMBT5087LT1G
Q3
R8 47K
3
Q1-2
FDG6301N
2
Q1-1
FDG6301N
4
6
4.1V
3
4
Q2-2
FDG6304P
J3
BAT ENB
R7
200K
7
2
13
2
BT1
CBC050
BT2
CBC012
1
D2
ZR40401F41TA
1
2
3
Q2-1
FDG6304P
1
6
5
1
5
2
R5
1K
3
1
Figure 3. Schematic, Cymbet Epson RTC Demo Board.
Note: Cypress is a Registered Trademark of Cypress Corporation. All other referenced terms or product names are the property of their
respective owners.
© Cymbet Corporation • 18326 Joplin Street, Elk River, MN 55330 • 763-633-1780 • www.cymbet.com
DOC-111006 RevA
Page 3