Download st-7000-c series - Extranet

TEC POS Terminal
ST-7000-C SERIES
Product Description
Document No. EO10-12027
Original
(Revised
Jun., 2005
)
Printed in Japan
EO10-12027
TABLE OF CONTENTS
Page
1. OUTLINE OF THE SYSTEM-------------------------------------------------------------------------1- 1
1.1
Features of the POS Terminal -------------------------------------------------------------------------- 1- 1
1.2
Description of Model Number --------------------------------------------------------------------------- 1- 2
1.3 Appearance and Dimensions --------------------------------------------------------------------------- 1- 3
1.3.1 Front View/Rear View/Connectors ---------------------------------------------------------------------1- 3
1.4 Basic Specifications --------------------------------------------------------------------------------------- 1- 5
1.4.1 Engine Specifications--------------------------------------------------------------------------------------1- 6
1.4.2 Operating Environment ----------------------------------------------------------------------------------1-13
1.4.3 Power Supply Specifications ---------------------------------------------------------------------------1-13
2. DETAILED INFORMATION--------------------------------------------------------------------------2- 1
2.1
Block Diagram ---------------------------------------------------------------------------------------------- 2- 1
2.2
Block Diagram (PC Board Level)----------------------------------------------------------------------- 2- 2
2.3
Detailed Information about PC Standard Functions ----------------------------------------------- 2- 3
3. DETAILED INFORMATION OF EACH PC BOARD-------------------------------------------3- 1
3.1
CLE266-ENGINE PC Board----------------------------------------------------------------------------- 3- 1
3.2
ST7000E RISER PC Board------------------------------------------------------------------------------ 3- 3
3.3
S.CROSS-IO PC Board ---------------------------------------------------------------------------------- 3- 6
CAUTION!
1. This manual may not be copied in whole or in part without prior written permission of TOSHIBA
TEC.
2. The contents of this manual may be changed without notification.
3. Please refer to your local Authorised Service representative with regard to any queries you
may have in this manual.
Copyright © 2005
by TOSHIBA TEC CORPORATION
All Rights Reserved
570 Ohito, Izunokuni-shi, Shizuoka-ken, JAPAN
1. OUTLINE OF THE SYSTEM
EO10-12027
1.1 Features of the POS Terminal
1.
OUTLINE OF THE SYSTEM
TEC POS terminal has been developed on the basis of the industry standard PC architecture and with the
addition of POS functions, therefore, the POS terminal supports open platform based on the PC architecture.
ST-7000-C Series, succeeding the specification of the ST-6500 series and the expandability of the currently
released ST-7000 series, adopts a GHz-class CPU (Intel Celeron 1.2 GHz).
1.1
Features of the POS Terminal
(1) The Intel Celeron 1.2 GHz CPU is adopted. (It is not possible to upgrade the CPU.)
(2) The 128 MB memory (non-ECC type) is installed as standard. Up to 2 GB memory can be installed.
(3) Compact design body is adopted in common with the currently released ST-7000 series.
(4) The four serial ports (COM1 to COM4), a parallel port, and a USB port are provided as standard. According
to the option I/O board kit, the COM ports and the USB ports are expandable.
The option I/O board kit is selectable from the following.
• KIT-7000-PUSB-QM (Full I/O (one COM port + three 12V P-USB + one 24V P USB) type))
• KIT-7000-2COM-QM (one COM + one USB type)
(5) Windows® XP Professional/Embedded, Windows® 2000, MS-DOS and Linux are supported, however,
neither Windows® 95/98/Me nor Windows® is supported.
(6) Same as the ST-7000 series, maintainability has been improved by adopting module design, which allows
easy disassembly without technical tools.
(7) A maximum of the two option HDDs and the option CD-R/RD drive can be installed.
NOTES:
1. Windows 2000 and Windows XP are registered trademarks of Microsoft Corporation.
2. Intel and Celeron are registered trademarks of Intel Corporation.
1- 1
1. OUTLINE OF THE SYSTEM
EO10-12027
(Revision Date: Sept. 28, 2007)
1.2 Description of Model Number
1.2
Description of Model Number
ST-7000- T T - T T T T - T QM - T
RoHS Compliance
Blank: Non-RoHS compliant model
R:
RoHS compliant model
Destination, Country/Region Code
QM: Standard for Worldwide
Pre-installed OS
Blank: None
∗ 1:
Windows XP Embedded®
Hardware Component
00
Not available
LVDS/DVI
Board
Not available
Not available
Not available
01
HDD:30G x 1
LVDS x 2
Not available
3-pin
Not available
Available
02
HDD:30G x 2
LVDS x 2
Not available
3-pin
Available
Available
HDD
∗
∗
Wireless
Board
Not available
Power Supply
Cable
Not available
RAID Board
UPS
Cabinet Color 00-02: Fair White, 04: Cool Black
CPU Type, CPU Clock
C: Celeron®1.2GHz
E: Celeron®2 GHz
F: Pentium®4 2.8GHz
Memory Capacity
1: 128 MB
2: 256 MB
3: 384 MB
4: 512 MB
5: 768 MB
M/S Classification
M: Master (for no classification)
∗ S: Satellite
Usage
∗ M: POS for mass sales shops
∗ S: POS for specialty shops
∗ F: POS for restaurants
W: Common
∗: Japan model
NOTE: Some combinations of the above specifications are not released as products.
For details, please contact your nearest authorized TOSHIBA TEC representative.
1- 2
1. OUTLINE OF THE SYSTEM
EO10-12027
1.3 Appearance and Dimensions
1.3
Appearance and Dimensions
1.3.1 Front View/Rear View/Connectors
< Front View >
Front Panel
Front Panel Lock
Power LED
HDD LED
POWER LED
Cover Catch
HDD LED
Reset Switch
CD-RW Drive
(Option)
Volume
Power Switch
USB5 Connector
< Rear View >
Cable Cover
NOTE:
Be sure to attach the cable cover for protecting the cables.
1- 3
1. OUTLINE OF THE SYSTEM
EO10-12027
1.3 Appearance and Dimensions
< Connectors >
Line-out
Mic-in
Not Used (Japan model only)
Powered USB x 4
COM5
(Option
USB0
12V-1
USB2
12V-3
USB1
12V-2
PCI Slot
COM6 (Option)*
USB3
24V
24V DC
Outlet
COM1
COM2
LPT1
COM3
COM4
VGA
LAN
LVDS (Option)
DRW1 DRW2
USB4 (Option)
5V USB
AC Outlet
AC Inlet
Not used (Japan model only)
PS/2 (Keyboard or Mouse)
: Option
*: COM6 is installed on the PCI slot.
NOTE:
The socket of USB0 to USB3 ports consists of a power supply connector (12V for USB0 to USB2,
and 24V for USB3) and a 5V USB connector. This USB connector can be used in the same way
as a general 5V USB connector.
USB0
USB1
USB2
USB3
Power Supply Connector
5V USB Connector
1- 4
1. OUTLINE OF THE SYSTEM
EO10-12027
1.4 Basic Specifications
1.4
Basic Specifications
Item
Description
CPU
BIOS ROM
Chipset
Celeron 1.2 GHz
Flash ROM 1 MB
VIA: CLE266 + VT8235M
Memory
128 MB (DDR SDRAM)
HDD
CD-R/RW
FDD
Display interface
LAN
Sound
Interface
PS/2
COM1
COM2
COM3
COM4
Option
(Up to two units of the 3.5 inch HDDs can be installed.)
Option
(Only one unit of the CD-R/RW can be installed.)
Option (External USB interface type)
RGB (Mini D-sub 15-pin) x 1
Option LVDS: KIT-7000-DISP3-QM (F.F.U)
10/100Base TX (RJ-45 modular connector (with LED))
Option
1 port (MINI-DIN 6-pin)
Provided D-SUB 9-pin male
Provided D-SUB 9-pin male
Provided D-SUB 9-pin female (with +5V, +12V)
Provided D-SUB 9-pin female (with +5V, +12V)
Option
D-SUB 9-pin female (with +5V, +12V)
COM6
USB0
USB1
USB2
Option
Option
Option
Option
D-SUB 9-pin female (with +5V, +12V)
12V powered USB
12V powered USB
12V powered USB
USB3
Option
24V powered USB
USB4
Option
5V USB
USB5
Provided
5V USB
Drawer
Parallel
PCI
+24VOUT
2 ports (Modular type, fitted with the drive circuit)
1 port (D-SUB 25-pin female)
2 slots (Up to 140 mm size)
1 port (DIN 3-pin)
None
Supported OS
Power consumption
Dimension
NOTE:
PC2100-compliant, non-ECC type
(Up to 2 GB memory is installed.)
COM5
UPS battery
Weight
Remarks
®
Locally purchased
Locally purchased
(KIT-7000-CD-QM is required.)
Locally purchased
Adopts a graphic controller which
contains a chipset.
Supporting Wake-On-LAN function
KIT-7000-PUSB-QM is required.
See NOTE below.
KIT-7000-PUSB-QM or KIT-70002COM-QM is required.
KIT-7000-COM-QM is required.
KIT-7000-PUSB-QM or KIT-70002COM-QM is required.
The Number of additional USB ports
differ depending on the option PC
board.
Option LVDS board is required.
Provided on the front side of the POS
terminal.
DC 24V power supply for the printer
None of the UPS battery can be
added.
Windows® XP Professional/Embedded,
®
Windows 2000, MS-DOS and Linux
190 W
315 mm (W) x 466 mm (D) x 112.5 mm
(including the rubber feet and cable cover)
9.5 Kg
(not including 2 HDDs, CD-RW, PCI, and packing
materials)
When using the PS/2 keyboard and the PS/2 mouse together, please prepare a store-bought PS/2
splitter which meets the following wiring pattern.
1
2
3
4
5
6
1
3
4
5
Keyboard
1
3
4
5
Mouse
1- 5
1. OUTLINE OF THE SYSTEM
EO10-12027
(Revision Date: Mar. 16, 2007)
1.4 Basic Specifications
1.4.1
Engine Specifications
1.4.1.1 PC Functions
(1) CPU
Intel® Celeron® 1.2 GHz (100 MHz x 12): Socket-370
• Binary interchange with the applications which run on Intel 80x86 family products.
• Optimized for 32-bit applications which run on 32-bit OS.
• Independently dedicated external system bus and dedicated internal high-speed
cache bus
• Embedded with the 16-KB L1 caches for data and for instructions
• Integrates an on-die 256-KB L2 cache
• Memory address buffer is scalable up to 4-GB memory.
• The MMX (Matrix Math eXtensions) technology is adopted.
• The 370-pin package type
(2) BIOS-ROM
Flash ROM 1 MB
• Supports the temperature/voltage monitoring function and the error information log
function
• Supports the shadow RAM BIOS function
• Programs below are stored in the system BIOS.
- System BIOS program
- VGA BIOS program
- NETWORK BOOT BIOS program
- BIOS DIAG program
(3) Memory (DRAM)
128MB DDR SDRAM (non-ECC type)
Configuration:
Two (2) slots are provided for the 2.5 V, 184-pin DIMM connector.
The 128-MB memory module is installed into either slot as standard.
Memory type:
PC2100-compliant, unbuffered, non-ECC type memory module
- Supporting a 16 M x 64 bit/32 M x 64 bit/64 M x 64 bit, unbuffered,
non-ECC type DDR-SDRAM module
- Supporting CL 2/2.5/3 and 1T per command
Capacity:
Standard 128 MB/Max. 2 GB
Max. 1 GB/slot can be equipped.
NOTE: RoHS-compliant memories below are recommended for the ST-7000-WM1C00-QM-R
(4) Chipset
Manufacturer
Model Name
CIMA (Nanya）
CIMA (Nanya）
CIMA (Nanya）
CIMA (Nanya）
CIMA (Nanya）
C128M8427D-NAT61AN
C256M8427D-NAT1AN
C256M8431D-NAT1AN
C512M8427D-NAT1N
C512M8431D-NATN
Memory
Type
DDR-DIMM PC2700
DDR-DIMM PC2700
DDR-DIMM PC3200
DDR-DIMM PC2700
DDR-DIMM PC3200
No. of
Pins
184pin
184pin
184pin
184pin
184pin
Memory
Size
128MB
256MB
256MB
512MB
512MB
VIA Technologies, Inc.: CLE266 (North Bridge) + VT8235M (South Bridge)
Basic Function of CLE266 (North Bridge):
• CPU Interface (100/133 MHz FSB controller)
• DDR DRAM controller
• Internal graphic controller
Basic Function of VT8235M (South Bridge):
• Low pin count (LPC) interface
• 8259-based interrupt controller
• I/O APIC
• 8254-based timer controller
• PCI2.2 bus interface
• LAN controller
• USB1.1/2.0 host controller
• AC’97 interface
• SM bus
• IDE controller (ATA-33/66/100/133)
• Real Time Clock
• PS/2 (Keyboard and Mouse) interface
• 8237-based DMA controller
1- 6
1. OUTLINE OF THE SYSTEM
EO10-12027
(Revision Date: Mar. 16, 2007)
1.4 Basic Specifications
(5) Super I/O Chip
Equipped with SMSC’s LPC47M287
Basic Function:
• Controls the COM1, COM2 and LPT1
• FAN control
• Voltage monitor (CPU voltage/2.5V/3.3V/5V/12V)
(6) POS Gate Array
Equipped with the TEC POS Gate Array EC-B171
(connected to the South Bridge via LPC-ISA Bridge)
Basic Function:
• Controls Drawer 1 and Drawer 2
• Controls COM3 to COM6
(7) PS/2 Interface
PS/2 (Built in Chipset (South Bridge))
• A MINI-DIN 6-pin connector is provided on the rear side of the POS terminal.
• Controls the PS/2 keyboard (PC keyboard or POS keyboard) and the mouse.
(When using the PS/2 keyboard and the PS/2 mouse together, please prepare a
store-bought PS/2 splitter.)
(8) Serial Interface
COM1 and COM2 (Built in super I/O chip)
• PC standard COM1 and COM2 ports
• D-SUB 9-pin connector (male) equipped on the POS terminal
Pin
Signal
I/O
1
DCD (Data Carrier Detect)
I
2
RXD (Received Data)
I
3
TXD (Send Date)
O
4
DTR (Data Terminal Ready)
O
5
GND
P
6
DSR (Data Set Ready)
I
7
RTS (Request To send)
O
8
CTS (Clear To Send)
I
9
RI (Ring Indicator)
I
5
1
6
9
(9) Parallel Interface
13
25
1
14
LPT1 (Bi-directional) (Built in the super I/O chip)
• PC standard Centronics printer port
• Selectable from Output only/Bi-directional/EPP/ECP by the BIOS setting
• D-SUB 25-pin connector (female) is equipped on the POS terminal.
PIN
Signal
I/O
PIN
Signal
I/O
1
/STROBE
O
14
/AFD
O
2
DATA0
I/O
15
/ERROR
I
3
DATA1
I/O
16
/INIT
O
4
DATA2
I/O
17
/SLIN
O
5
DATA3
I/O
18
GND
--6
DATA4
I/O
19
GND
--7
DATA5
I/O
20
GND
--8
DATA6
I/O
21
GND
--9
DATA7
I/O
22
GND
--10
/ACK
I
23
GND
--11
BUSY
I
24
GND
--12
PE
I
25
GND
--13
SLCT
I/O
1- 7
1. OUTLINE OF THE SYSTEM
EO10-12027
(Revision Date: Mar. 16, 2007)
1.4 Basic Specifications
(10) Real Time Clock and Lithium Battery
Primary battery
• The lithium battery is used for backing up the clock and the setup information.
The battery life is five years.
• The clock is to be accurate within ± 90 seconds per month.
(11) Speaker
Assigned to the I/O interface signal of the RISER PC board.
• A small speaker is built in on the front of the control section (RISER PC board).
• Volume can be set with the control on the front side of the POS terminal.
(12) USB Interface, Powered USB Interface
Host controller which is contained in VT8235M (South Bridge)
• Conforming to the Universal Hub Controller Interface (UHCI)
Conforming to the Enhanced Host Controller Interface (EHCI)
• The USB host controller controls the six USB2.0/1.1 ports.
• The four (4) out of six (6) USB2.0/1.1 ports are connectable via the RISER PC board
with the above USB host controller.
• Standard USB: A port is provided on the front side of the POS terminal via the
RISRER PC board.
• Four Powered USB ports equipped with 12V/24V power supply can be used. These
ports are provided on the I/O PC board.
• Available under Windows®2000 and Windows®XP.
• Powered USB should be connected while the system power is on.
Available current for USB ports
Voltage
Max.
Remarks
5V USB
A maximum of 0.5 A is available
for one port.
12V USB
A maximum of 1.0 A is available
Compliant with Powered USB
for one port.
(1.5 A peak/ Less than 2 seconds)
24V USB
A maximum of 2.0 A is available
Compliant with Powered USB
for one port.
(5 A peak/ Less than 2 seconds)
NOTE: The socket of USB0 to USB3 ports consists of a power supply connector
(12V for USB0 to USB2, and 24V for USB3) and a 5V USB connector. This
USB connector can be used in the same way as a general 5V USB
connector.
Power Supply Connector
5V USB Connector
1- 8
1. OUTLINE OF THE SYSTEM
EO10-12027
(Revision Date: Mar. 16, 2007)
1.4 Basic Specifications
(13) LAN Interface
Conforming to the IEEE802.3 10BASE-T/100BASE-TX Standard
• LAN controller:
VIA Technologies Inc. VT6105
• Interface:
PCI bus master interface
• Connector:
RJ-45 modular connector (with LED)
LED status
Type of LED (Color)
LNK/ACT (Green)
SPEED (Yellow)
LNK/ACT LED
(Green)
SPEED LED
(Yellow)
LED Status
Off
On
Blink
Off
On
Condition
A LAN link has not been established.
A LAN link has been established.
Frame being sent/received
Connected with 10BASE-T
Connected with 100BASE-TX
IDE interface (Primary/Secondary)
• IDE controller: VT8235 (South Bridge)
• Conforming to PIO mode and Ultra ATA/33/66/100/133
• Converts to a 2.54-mm-pitch, 40-pin connector with the RISER PC board.
Be sure to prepare an option ATA 80-pin cable for connecting the HDD.
• A maximum of two 3.5-inch HDDs (master, slave) can be installed.
NOTE: For details, refer to the HDD specification manual published by HDD
manufacturer.
(15) CD-ROM Drive
Connected to the secondary side of the IDE interface in use.
When connecting a CD-ROM drive, the SLIM CD interface conversion kit (KIT-7000CD-QM) is required.
The IDE interface can be converted to 50-pin (JAE: KX-50K5D) on the S.CROSS-CDCONV PC board for allowing the connection of a SLIM-type (using a JAE: KX-50KLDL
connector or equivalent) CD-ROM drive, etc.
CD-ROM Power Cable
40-pin Connector
SLIM-type CD-ROM Drive
50-pin Connector
(14) HDD Interface
IDE Cable
S.CROSS-CD-CONV PC Board
KIT-7000-CD-QM
TOSHIBA TEC approved CD-R/RW drive
Model Number
Manufacturer
CD-W224E-A93
TEAC
1- 9
Remarks
Slim type CD-R/RW Drive
1. OUTLINE OF THE SYSTEM
EO10-12027
(Revision Date: Mar. 16, 2007)
1.4 Basic Specifications
(16) Internal graphic interface
1) RGB interface: Analog RGB
• VGA controller:
Graphic controller embedded with VIA CLE266
• VIDEO memory:
Using system memory (according to the BIOS setting)
• VGA BIOS ROM:
Stored in system BIOS
• Dual display:
The internal controller supports the dual display function
between the on-board RGB and the expansion LCD
interface (piggyback board) under the OS such as
Windows® XP.
Details are depending on the device driver setting.
Resolution & Maximum number of colors
OS
DOS
Windows
VIDEO memory
1 MB
8/16/32/64 MB
640 x 480 (16M)
640 x 480 (64K)
Resolution
800 x 600 (16M)
800 x 600 (64K)
(Maximum number of
1,024 x 768 (16M)
1,024 x 768 (256)
colors)
1,152 x 864 (16M)
1,280 x 1,024 (16M)
• Connection with CRT: 15-pin VGA connector (female)
1
5
PIN
Signal
I/O
PIN
Signal
I/O
1
RED
O
9
NC
NC
2
GREEN
O
10
GND
P
15
11
3
BLUE
O
11
NC
NC
4
NC
NC
12
SPD
I/O
5
GND
P
13
HSYNC
O
6
AGND
P
14
VSYNC
O
7
AGND
P
15
SPCLK
I/O
8
AGND
P
2) Expansion LCD interface: option LVDS board
(expandable with the piggyback board)
This interface is installed on the ENGINE PC board with the piggyback board, and it
converts the LCD interface signal sent from the ENGINE PC board to the LVDS
signal.
LVDS interface
• VGA controller:
Graphic controller embedded with VIA CLE266
• VIDEO memory:
Using system memory (according to the BIOS setting)
• Resolution:
800 x 600
• Number of colors:
Max. 65,536 colors
• Connection with engine: Installed on the ENGINE PC board with the piggyback
board (TOSHIBA TEC original board).
• Touch panel control:
Connected from the LVDS interface to COM4 or COM6
on the ENGINE PC board.
• Speaker control:
Connected to the internal speaker signal.
• Dual display:
The internal controller supports the dual display
function between the on-board RGB and the expansion
LCD interface (piggyback board) under the OS such as
Windows® XP.
Details are depending on the device driver setting.
1-10
1. OUTLINE OF THE SYSTEM
EO10-12027
(Revision Date: Mar. 16, 2007)
1.4 Basic Specifications
• Connection with TFT:
TOSHIBA TEC original interface 26-pin connector with
lock.
Not compatible with the pins of the conventional
products.
Signal: LVDS signal (The connector includes the touch
panel control RS-232C and speaker control signals.)
PIN
Signal
I/O
PIN
Signal
I/O
1
+5V
--14 TXOUT0O
2
TX0GND
--15 TXOUT0+
O
3
+5VC
--16 +12V
--4
TXOUT1O
17 TX1GND
--5
TXOUT1+
O
18 +12V
--6
SPKR
O
19 RXD
I
7
TXD
O
20 DTR
O
8
CTS
I
21 RTS
O
9
+12V
--22 TXOUT2O
10 TX2GND
--23 TXOUT2+
O
11 BLK
O
24 DSR
I
12 TXCLKO
25 TXCGND
--13 TXCLK+
O
26 GND
--Up to two PCI standard boards can be inserted.
• Available board size
Lower (Slot0#):
Up to 140 mm length x 1
Upper (Slot1#):
Up to 140 mm length x 1
• PCI revision
Supporting PCI 2.2
• The power is shared by the PCI board, HDDs, USB devices, and other option devices.
(Refer to Section 1.4.3 Power Supply Specifications.)
(17) PCI bus
(18) Interface on the I/O PC Board (option)
The option I/O PC board is connected to the RISER PC board.
The following I/O ports are expandable depending on the I/O PC board.
I/O PC Board 1: (KIT-7000-PUSB-QM: Full I/O type)
• Four (4) Powered USB ports (P-USB (12V) x 3, P-USB (24V) x 1)
• AC’97 (MIC IN, LINE OUT)
• Two serial ports (COM5 and COM6 (Header connector))
• Drawer interface (Japan model only)
• Power supply connector for the LIU and printer (Japan model only)
I/O PC Board 2: (KIT-7000-2COM-QM: Two COM ports and one 24V P-USB port type)
• Two serial ports (COM5 and COM6 (Header connector))
• A Powered USB port (P-USB (24V) x 1)
Expansion I/O Port
Serial
USB
AC’97
Other
COM5
COM6
12V P-USB (USB0)
12V P-USB (USB1)
12V P-USB (USB2)
24V P-USB (USB3)
LINE OUT
MIC IN
Drawer
PRT PWR
LIU PWR
I/O PC Board 1
KIT-7000-PUSB-QM
O
O
O
O
O
O
O
O
O
O
O
1-11
I/O PC Board 2
KIT-7000-2COM-QM
O
O
X
X
X
O
X
X
X
X
X
Remarks
Header connector
Not used for overseas
model
(Japan model only)
1. OUTLINE OF THE SYSTEM
EO10-12027
(revision Date: Mar. 16, 2007)
1.4 Basic Specifications
(19) Interface on the RISER PC Board
The following I/O ports on the RISER PC board are expandable.
• POWER LED, HDD LED, POWER SW, RESET SW, BUZZER volume
• HDD interface (IDE Interface Primary/Secondary), HDD/CD-ROM power
• ATX PS interface
• PCI interface
• USB interface
• 12-24V Step-Up (Boost) DC-DC converter
• Printer power connector (24V)
• IO board interface
• Wake On LAN
• PS/2 keyboard (not available)
• FAN connector
(20) Watchdog Timer Function
Together with BIOS and OEM drivers, the Watchdog Timer function is activated, which prevents a hang at
the time of OS start-up. The Watchdog Timer is a circuit for monitoring the microcomputer’s performance
and the system condition and for inquiring the system performance. When detecting some fault condition,
an interrupt signal is immediately sent to the CPU and a system restart is performed, resulting in that the
system returns from the hung state into normal operation.
1.4.1.2 POS Functions
(1) Drawer interface
A maximum of two drawers containing the TOSHIBA TEC standard 24V drive circuit can be connected.
• 4-pin modular type x 2
• 4-pin type x 1
(Not used, Japan model only: when the option KIT-7000-PUSB-QM is installed.)
Connector specifications
4-pin modular type
Drawer Connector Type
PC Board
Remarks
Drive circuit contained on the drawer
4-pin modular
Engine board
side
Drawer 1
Not
used, Japan model only
4-pin type
IO board
4-pin
Drive circuit not contained on the
(Option)
drawer side
Drive circuit contained on the drawer
Drawer 2 4-pin modular
Engine board
side
(2) Serial interface
COM1, COM2:
COM3, COM4:
COM5, COM6:
9-pin DSUB (male) as standard
9-pin DSUB (female) as standard.
9-pin DSUB (female) (option)
+5V and +12V can be supplied.
+5V and +12V can be supplied.
COM1 and COM2
COM5 is provided on the I/O PC board, and COM6 is provided on the I/O PC board or
the 10-pin box connector is provided on the RISER PC board. When using COM6, the
option KIT-7000-COM-QM is required.
COM3 to COM6 do not have the RI and DCD signals.
COM3 to COM6
(3) Powered USB (Installed on the I/O board): option
Four Powered USB ports equipped with 12V/24V power supply can be used. These ports are provided on
the I/O PC board.
• Number of ports supported
12V P-USB x 3, 24V P-USB x 1 (KIT-7000-PUSB-QM)
24V P-USB x 1 (KIT-7000-2COM-QM)
1-12
1. OUTLINE OF THE SYSTEM
EO10-12027
1.4 Basic Specifications
1.4.2 Operating Environment
Temperature
Relative humidity
Height above sea level
Operating:
Storage:
Transportation:
Operating:
Storage:
Transportation:
Operating:
Non-operating:
5 °C to 35 °C
-20 °C to 60 °C
-20 °C to 60 °C
10% to 80%RH
No condensation
10% to 90%RH
No condensation
10% to 90%RH
No condensation
-60 m to 3,000 m
-60 m to 12,000 m
1.4.3 Power Supply Specifications
Input voltage/
Consumption current
(with outlet)
Output voltage
Outlet
Dimension
Power cord
Power supply capacity
AC
100V to 240V
+10%, -10%
50/60 Hz
4.8A to 2.3A
+3.3V ±5%, +5V ±5%, +12V ±5%, -12V ±5%, 5VB ±5%
ATX compliance: 20-pin connector, ATX12V, 4-pin connector,
HDD connector 4-pin x 2
AC
100V to 240V
+10%, -10%
50/60 Hz
2.0A to 1.0A
An outlet supplies the power in conjunction with the engine box’s power on/off.
215 mm (D) x 100 mm (W) x 60 mm (H)
A power cord is not enclosed with the product. Please prepare a power cord locally.
To prevent accidents such as electric shocks and malfunctions, connect the ground to
the ground terminal of the outlet.
In the United States of America, use the power cord described below:
Power cord
- UL listed, type SVT, 18/3AWG, rated minimum 125V, 10A
Attachment plug
- Moulded on type, parallel-blade grounding plug, NEMA5-15P configuration
- Moulded on type having standard IEC CE-22 female configuration
The power is shared by the PCI bus, expandable HDDs, USB devices, and other
option devices in the following range:
+24V
2A (Peak 10A)
+12V
3A (Peak 8.5A)
+5V
3.2A (Peak 9A)
NOTES:
1. Total consumption current of option devices connected to the POS terminal should
be within rated current of each voltage (+24V, +12V, +5V). If it exceeds the rated
current, the POS terminal may malfunction due to shortage of power supply.
2. The system should be constructed so that the total power consumption does not
exceed the power supply capacity (133W). As the CPU (Celeron 1.2GHz)
consumes a maximum of 36W, the power consumption of the option devices
should be within 97W in total.
1-13
1. OUTLINE OF THE SYSTEM
EO10-12027
1.4 Basic Specifications
Example) The following shows consumption current and power consumption of each voltage when connecting
the option devices below to the POS terminal.
• DRWST-51A
• PKBST-50 (with PC keyboard)
• TRJST-52
• USB FDD (Logitec: LFD-31U4)
• TFTST-56T
• HDD (Western Digital: WD400BB)
• LIUST-51
• CD-R/RW drive (TEAC: CD-W224E)
• HS-530
Consumption current: Maximum values are used here.
Option device
+24V
DRWST-51A
0.2A
TRJST-52
2A
TFTST-56T
--LIUST-51
--HS-530
--PKBST-50 (with PC keyboard)
--USB FDD (Logitec: LFD-31U4)
--HDD (Western Digital: WD400BB)
--CD-R/RW Ddive (TEAC: CD-W224E)
--Total
2.2A
+12V
----0.7A
0.4A
------0.35A
--1.45A
+5V
--0.6A
----0.2A
0.35A
0.48A
0.63A
1.6A
3.86A
Power consumption: 36W + (2.2A x 24V)W + (1.45A x 12V)W + (3.86A x 5V)W = 125.5W
CPU
NOTE:
+24V Power
+12V Power
+5V Power
The above reference values are obtained on the assumption that all the option devices are
performed simultaneously. The consumption current and the power consumption differ
depending on operating environment.
Current requirements of the option devices connected to the POS terminal (reference)
Option device
DRWST-51A
DRWST-56
TRJST-52
TRST-56 (external power supply)
TFTST-56T
LKBST-65
LIUST-51
HS-530
PKBST-50 with PC keyboard
PKBST-50 without PC keyboard
*HDD
Read/Write
Idle
Standby
Sleep
**CD-R/RW Drive
+24V (3A)
0.2A
0.2A
2A
-----
Standby/Sleep
Writing at 24x-speed
Active
At starting
At seeking
At ejecting
USB FDD (Logitec: LFD-31U4)
*HDD:
Western Digital WD400BB
**CD-R/RW Drive: TEAC CD-W224E
1-14
-------------------------------
+12V (3A)
--------0.7A
0.8A
0.4A
------0.35A
0.34A
0.025A
0.025A
---------------
+5V (5A)
--------0.6A
0.6A
--0.2A
0.35A
0.04A
0.63A
0.61A
0.19A
0.08A
0.05A
1.1A
1.0A
1.4A
1.4A
1.6A
0.48A
1. OUTLINE OF THE SYSTEM
EO10-12027
1.4 Basic Specifications
When purchasing the power cord
Since the power cord set is not enclosed in this unit, please purchase an approved one that meets the following
standard from your authorized TOSHIBA TEC representative.
(As of September 2004)
Certification
mark
Certification
mark
Certification
mark
Country
Agency
VDE
Sweden
SEMKKO
Ireland
NSAI
Switzerland
SEV
CEBEC
Italy
IMQ
UK
ASTA
Canada
CSA
Japan
METI
UK
BSI
Denmark
DEMKO
Netherlands
KEMA
U.S.A.
UL
Finland
FEI
Norway
NEMKO
Europe
HAR
France
UTE
Spain
AEE
Country
Agency
SAA
Germany
Austria
OVE
Belgium
Country
Agency
Australia
Power Cord Instruction
1. For use with 100 – 125 Vac mains power supply, please select a power cord rated Min. 125V, 10A.
2. For use with 200 – 240 Vac mains power supply, please select a power cord rated Min. 250V.
3. Please select a power cord with the length of 4.5 m or less.
Country/Region
Power Cord
Rated (Min.)
Type
North America
Europe
United Kingdom
Australia
125V, 10A
SVT
250V
H05VV-F
250V
H05VV-F
No. 3/18AWG
3 x 0.75 mm2
3 x 0.75 mm2
3 x 0.75 mm2
250V, *1
250V, *1
250V
AS3191 approved,
Light or Ordinary Duty type
Conductor size
(Min.)
Plug Configuration
(locally approved
type)
Rated (Min.)
125V, 10A
250V, 10A
*1: Minimum 125% of the rated current of the product.
1-15
2. DETAILED INFORMATION
EO10-12027
2.1 Block Diagram
2. DETAILED INFORMATION
2.1 Block Diagram
: Option
ENGINE PC Board
LCD I/F Board (Piggy)
Celeron 1.2GHz (Socket370)
TTL
TTL-LVDS Convert
LVDS
COM4 Header
Touch Panel
DVO
FLASH-ROM
512KB
COM3 Header
USB#4 (5V USB)
Basic Memory
Max.1GB
Expanded Memory
Max.1GB
COM5 Header
RGB
VGA
COM1
Real Time Clock
COM2
PS/2 Keyboard
Mouse I/F
Parallel Port
10/100BASE-/TX
HDD
EC-B171
COM3
COM4
Drawer 1
Drawer
(Modular type)
Drawer 2
Drawer
(Modular type)
IDE Primary
COM5
HDD
COM6
CD-RW
IDE Secondary
12V P-USB#0
USB#5 (Front)
K/B
12V P-USB#1
PS/2 Keyboard I/F
12V P-USB#2
24V P-USB#3
Reset SW
Line-out
AC'97
Codec
Power SW
Mic-in
Drive Circuit
I/O PC Board
PC-BEEP
Speaker
Power Control
ATX
PCI Slot#1
COM6 Header
PCI Slot#2
RISER PC Board
Booster Circuit
(12V to 24V)
AC-DC Power
Supply
24V DC out
AC OUTLET
AC100/240V
ATX
2- 1
2. DETAILED INFORMATION
EO10-12027
2.2 Block Diagram (PC Board Level)
2.2
Block Diagram (PC Board Level)
LCD I/F Board (Piggy)
100-pin
ENGINE Board
TTL-LVDS
1st LVDS
COM5 header
Intel Celeron 1.2GHz
COM4 header
USB4
TTL
DVO
RGB
VGA
DDR266
None ECC (up to 2GB)
North Bridge
VIA CLE266
DDR DIMM0 (184-pin)
DDR DIMM1 (184-pin)
V-Link
COM1
Super I/O
COM2
Parallel
UDMA66/100
BIOS
Primary IDE
LPC-47M287
LPC
Secondary IDE
South
Bridge
Back light
COM4
MOUSE
Back light
COM3
Gate Array
COM4
DRW1
EC-B171
ISA
DRW2
LPC-ISA
Bridge
EC-B160
VIA
VT8235M
PS/2
MOUSE/KB
KB
LAN
Controller
VIA
VT6105
LAN
PCI
USB0 to 5
Power & Control
COM6 header
PS/2
Slot#1
RISER Board
Slot#2
USB5
Power Control & DC-DC CNV
Speaker
RESET
VOL
SW
ATX
P-USB0
Power
P-USB1
ATX12V
AC97
Mic-in
P-USB2
P-USB3
DRW1
COM5
Line-out
Driver
Circuit
COM6 header
I/O Board
2- 2
Power Supply
AC
2. DETAILED INFORMATION
EO10-12027
2.3 Detailed Information about PC Standard Functions
2.3
Detailed Information about PC Standard Functions
Memory Map
00000h
RAM 640KB
A0000h
VRAM (Graphic mode) 64KB
B0000h
B8000h
VRAM (Text mode) 32KB
C0000h
VGA BIOS 64KB
(Shadow RAM)
D0000h
Data area for USB emulations
D8000h
UMB 64KB
LAN Boot ROM 64KB
(Shadow RAM)
E8000h
System ROM BIOS 64KB
(Shadow RAM)
100000h
RAM
2047MB (Max.)
80000000h
FEC00000h
APIC Control Register
FEC00040h
FFF00000h
System ROM BIOS 1MB
FFFFFFFFh
2- 3
2. DETAILED INFORMATION
EO10-12027
2.3 Detailed Information about PC Standard Functions
I/O Assignment
Address (hex)
0000-001Fh
0020-003Fh
0040-005Fh
0060-006Fh
0060h
0061h
0064h
0070-0077h
0078-007Fh
0080h
0081-008Fh
0090-0091h
0092h
0093-009Fh
00A0-00BFh
00C0-00DFh
00E0h
00F0-00FFh
0100h
0110-0117h
0118-011Fh
0120-0127h
0128-012Fh
0138-013Fh
0140,0144h
0142h
0146h
014Ah
014Eh
0152-0158h
0159-015Ch
0170-0177
01F0-01F7
0274-0277h
0279h
02E8-02EFh
02F0-02F7h
02F8-02FFh
0376
0378-037Fh
03B0-03BBh
03C0-03DFh
03E8-03EFh
03F0-03F5h
03F6
03F7
03F8-03FFh
0400-047Fh
0500-050Fh
0800-087Fh
0A79h
CF8-CFBh
CFC-CFFh
0D00-FFFFh
46E8h
D000-D01Fh
D400-D41Fh
D800-D81Fh
DC00-DC0Fh
E400-E4FFh
Function
Master DMA Controller
Master Interrrupt Controller
Timer/Counter
Keyboard Controller
KBC DATA
Misc Functions & Speaker Control
KBC Control
RTC/CMOS/NMI-Disable
Available for system use
Reserved(Debug port)
DMA Page Registers
Available for system use
System Control
Available for system use
Slave Interrupt Controller
Slave DMA Controller
System Reserve
Numeric Data Processor
Multiple Interruption 1
UPS Control(COM7)
System Reserve
System Reserve
COM5
System Reserve
System Reserve
System Reserve
Drawer
System Reserve
System Reserve
System Reserve
System Reserve
Secondary IDE
Primary IDE
ISA PNP Read Data Port
ISA PNP Read Data Port
COM4
COM6
COM2
Secondary IDE
Parallel Port
VGA Registers
VGA Registers
COM3
System Reserve
Primary IDE
System Reserve
COM1
VT8235 GPIO
SM Bus
LPC47M287 GPIO
ISA PNP Read Data Port
Configuration Address
Configuration Data
PCI Bus
VGA Registers
USB Host Controller
USB Host Controller
USB Host Controller
Bus Master IDE Controller
VIA VT6105 Rhine III Fast Ethernet Adapter
2- 4
PC/POS
PC
PC
PC
PC
PC
PC
PC
PC
PC
PC
PC
PC
PC
PC
PC
PC
PC
PC
POS
POS
POS
POS
POS
POS
POS
POS
POS
POS
POS
POS
POS
PC
PC
PC
PC
POS
POS
PC
PC
PC
PC
PC
POS
PC
PC
PC
PC
PC
PC
PC
PC
PC
PC
PC
PC
PC
PC
PC
PC
PC
IC
VT8235
VT8235
VT8235
VT8235
LPC47M287
VT8235
LPC47M287
VT8235
VT8235
VT8235
VT8235
VT8235
VT8235
VT8235
VT8235
VT8235
EC-B171
VT8235
EC-B171
EC-B171
EC-B171
EC-B171
EC-B171
EC-B171
EC-B171
EC-B171
EC-B171
EC-B171
EC-B171
EC-B171
EC-B171
VT8235
VT8235
VT8235
VT8235
EC-B171
EC-B171
LPC47M287
VT8235
LPC47M287
VT8623
VT8623
EC-B171
LPC47M287
VT8235
LPC47M287
LPC47M287
VT8235
VT8235
LPC47M287
VT8235
VT8235
VT8235
VT8235
VT8623
VT8235
VT8235
VT8235
VT8235
VT6105
Remarks
Back Light Control
Multiple Interruption 1
POS-IO#2
POS-IO#3
POS-IO#1
RELAY Control
Multiple Interruption 2 retrigger
Multiple Interruption 2 trigger input
PFL、M-ON
OCIA1
OCIA2
Floppy Controller
Floppy Controller
2. DETAILED INFORMATION
EO10-12027
2.3 Detailed Information about PC Standard Functions
Interruption Assignment
Interrupt Level
OS
Factor
Win2000
WinXP
DOS
Linux
NMI
IRQ0
Timer
Å
Å
Å
Å
IRQ1
Keyboard
Å
Å
Å
Å
IRQ2
8259 (Interrupt Controller)
Å
Å
Å
Å
IRQ3
COM2
Å
Å
Å
Å
IRQ4
COM1
Å
Å
Å
Å
IRQ5
COM6/COM7 (UPS) or
PCI/USB
Å
Å
Å
Å
IRQ6
FDD
Å
Å
Å
Å
IRQ7
COM5/ (LPT)
Å
Å
Å
Å
IRQ8
RTC
Å
Å
Å
Å
IRQ9
ACPI or PCI/USB
ACPI
ACPI
PCI/USB
ACPI
IRQ10
COM3
Å
Å
Å
Å
IRQ11
COM4
Å
Å
Å
Å
IRQ12
Mouse
Å
Å
Å
Å
IRQ13
CoProcessor
Å
Å
Å
Å
IRQ14
HDD (Primary)
Å
Å
Å
Å
IRQ15
HDD (Secondary)
Å
Å
Å
Å
PCI/USB
PCI/USB
PCI/USB
---
PCI/USB
APIC
IRQ16-23
Interrupt switch between COM6 and COM7
Type
COM6
I/O Address
Connection
I/O
2F0-2F7h
Connector
BIOS Setting
9-pin D-Sub
female
IRQ5
COM7
110-117h
UPS
Internal wiring
2- 5
3. DETAILED INFORMATION OF EACH PC BOARD
EO10-12027
3.1 CLE266-ENGINE PC Board
3. DETAILED INFORMATION OF EACH PC BOARD
3.1 CLE266-ENGINE PC Board
The CLE266-ENGINE PC board is a heart of the ST-7000 POS terminal. Most of main ICs, such as CPU
(Celeron 1.2 GHz), chipset, super I/O IC, gate array IC, are mounted on the PC board. Part of I/O interface,
which is controlled by the controller on the PC board, is mounted on the option I/O PC board via the RISER PC
board.
(1) PCB Layout
PS/2
CN1
Drawer1,2
CN2,3
LAN
CN4
VGA Connector
CN5
POS
Gate Array
EC-B171
VIA
VT6105
LAN
COM4
CN6
LPC-ISA
Bridge
EC-B160
LPC47M287
Super I/O
COM3
CN7
COM1, COM2
CN8
LPT Relay CN9
I/O Board Connector (120-pin)
CN10
To RISER
PC Board
CN11
VIA
VT8235M
VIA
CLE266
South Bridge
Socket370
North Bridge
To RISER
PC Board
CN12
DDR Memory CN14
DDR Memory CN15
CPU FAN
CN16
3- 1
3. DETAILED INFORMATION OF EACH PC BOARD
EO10-12027
3.1 CLE266-ENGINE PC Board
(2) Block Diagram
2.5V
CPU FAN CN16
CPU Core voltage
DC-DC Power Supply
Clock Generator
ICS9248
Socket 370
1.5V
1.25V
2.5V
VGA
Connector
CN5
Clock BUFFER
ICS93712
RGB
VIA
VT8623
North Bridge
TTL
DVO
DDR Memory CN14
DDR Memory CN15
IDE
AC'97 I/F
USB I/F (USB0-3,5)
PCI
COM5,6
K/B
PS/2
CN1
24V
12V
5V
3.3V
5VB
3.3VB
K/B
LPC I/F
BIOS
(8Mbit)
SMSC
LPC47M287
Super I/O
VIA
VT6105
LAN
LPC-ISA Bridge
EC-B160
POS Gate ARRAY
EC-B171
COM5,6
COM3
COM1
CN8
COM2
CN8
LPT
Relay
CN9
COM3
CN7
COM4
COM4
CN6
3- 2
Drawer
1,2
CN2,3
LAN
CN4
RISER CN11,12
COM3,4 (for T.P), COM5
V-LINK
12V
VIA
5V
VT8235M
3.3V
South Bridge
2.5V
2.5VB
USB4
I/O Board
Connector
(120-pin)
CN10
3. DETAILED INFORMATION OF EACH PC BOARD
EO10-12027
3.2 ST7000E RISER PC Board
(3) Connector Specifications
• DDR-SDRAM (CN14, CN15):
2.5V unbuffered type, 184-pin x 2
• RISER Connector (CN11, CN12):
PCI slot x 2
USB x 5
PS/2 keyboard
IDE x 2 (Ultra DMA-133/100/66/33)
Serial port x 2 (COM5, COM6)
Power supply/Power supply control signal
Hardware sensor
Speaker
• Peripheral I/O Connector:
Serial port x 4 (COM1, COM2, COM3, COM4)
Parallel port x 1 (with a relay cable)
VGA connector (RGB) x 1
PS/2 keyboard/mouse Connector x 1
(When using the PS/2 keyboard and the PS/2 mouse together, please
prepare a store-bought PS/2 splitter)
LAN x 1
Drawer (modular type) x 2
• I/O Board Connector (CN10):
Display signal (TTL, DVO)
Serial port x 3 (COM3, COM4, COM5)
USB x 1 (USB4)
• Other Connector:
3-pin type FAN connector (CN16) from which the FAN rotation speed
read signal is output
3.2 ST7000E RISER PC Board
The ST-7000E RISER PC board, equipped with a 24V booster circuit, relays the ENGINE PC board to the I/O PC
board. Various connectors such as PCI slots, IDE connectors, power supply connector, and I/O interface
connectors required for the front panel are mounted on the PC board.
In the 24V booster circuit, 24V is generated with 12V which is input from the ATX power supply.
(1) PCB Layout
CN8: CD R/RW PS
CN6: FAN1
CN7: FAN2 (Not installed)
CN103: UPS I/F
CN10: HDD PS
Power LED (Green)
HDD LED (Yellow)
Reset Switch
Volume
CN9: Speaker
CN11: LED OUT
CN17: PCI Slot #2
CN16: PCI Slot #1
CN102:
CN101: ATX 20-pin CN14:
ATX 12V 4-pin
Wake on LAN
CN18: IO BOARD I/F
CN15: Secondary IDE
Power Switch
CN401:
COM6
CN21: 24V OUT
CN2: USB Connector
CN3: PS/2 Connector
(Not installed)
CN5: Primary IDE
CN19: ENGINE BOARD I/F
3- 3
+5VB
3. DETAILED INFORMATION OF EACH PC BOARD
EO10-12027
3.2 ST7000E RISER PC Board
(2) Block Diagram
IDE I/F
IDE Primary
IDE Secondary
PCI I/F
PCI Slot#1
PCI Slot#2
Power Switch
Reset Switch
PS/2 K/B I/F Connector
USB#5 Connector
USB #0,1,2,3
AC97 I/F
COM5,6
DRW1
Speaker
12V
5V
Buzzer
IO I/F Connector
ENGINE I/F Connector
USB #5
COM6
Connector
3.3V
12V CPU
12V
24V
5V
5VB
24V
24V Out
Connector
3.3V
12V, 5V
HDD Power
Connector
3.3VB
ATX Connector
24V
12V, 5V
12V
5V
12V
CD-R/RW Power
Connector
FAN Power
Connector
5VB
3.3V
-12V
P_GOOD
PSON
12VCPU
12V-24V
Step up DC-DC Converter
24V
ATX Connector
12V CPU
5VB
UPS
Connector
UPS I/F
3- 4
5VB - 3.3VB
Regulator Circuit
3.3VB
3. DETAILED INFORMATION OF EACH PC BOARD
EO10-12027
3.2 ST7000E RISER PC Board
(3) Connector & Switch Specifications
• I/O Connector:
PCI slot x 2
E-IDE connector x 2 (Ultra DMA-133/100/66/33)
PS/2 keyboard connector x 1
USB port x 1
24V OUT connector x 1 (for the RJ printer)
UPS interface connector x 1 (Not used)
COM6 connector x 1
• Internal interface:
ENGINE PC board interface connector x 1
I/O PC board interface connector x 1
Power supply connector: ATX x 2
HDD PS connector x 1
CD-ROM PS connector x 1
Fan connector x 1
• Switch and Volume:
Power switch x 1
RESET switch x 1
Buzzer/Speaker volume x 1
3- 5
3. DETAILED INFORMATION OF EACH PC BOARD
EO10-12027
3.3 S.CROSS-IO PC Board
3.3 S.CROSS-IO PC Board
The S.CROSS-IO PC board is an expansion I/O PC board, unique to the ST-7000E series. By the addition of
this option PC board, COM5, three 12V P-USBs, 24V P-USB, PRTOUT (24V), LIUOUT (12V), DRW, MIC IN, and
LINEOUT are supported as standard. Also, COM6 is supported with the option KIT-7000-COM-QM, which was
released for the ST-7000 series. Depending on the required interface, the I/O PC board is selectable either from
KIT-7000-PUSB-QM or KIT-7000-2COM-QM.
(1) PCB Layout
• KIT-7000-PUSB-QM (full I/O type IO PC board)
COM5
•
CN12
COM6
CN2
CN3
CN4
CN5
12V
P-USB1
(USB0)
12V
P-USB2
(USB1)
12V
P-USB3
(USB2)
24V
P-USB1
(USB3)
CN6
CN7
CN8
24V
12V
DRW1
CN9
CN10
LINE
OUT
MIC
IN
CN11
RISER PC Board
CN1
FAN
CN11
RISER PC Board
CN13
KIT-7000-2COM-QM (1 COM + 1 USB type IO PC board)
CN13
CN1
COM5
FAN
CN12
COM6
CN2
CN3
CN4
CN5
12V
P-USB1
(USB0)
12V
P-USB2
(USB1)
12V
P-USB3
(USB2)
24V
P-USB1
(USB3)
CN
No.
CN10
CN9
MIC IN
LINE OUT
CN8
Drawer
CN2
CN3
CN4
CN5
CN1
CN12
CN6
CN13
CN11
CN7
12V P-USB (USB0)
12V P-USB (USB1)
12V P-USB (USB2)
24V P-USB (USB3)
COM5
COM6 (option)
PRTPWR
FAN
CONNECT WITH RISER
LIUPWR
CN Name
CN6
CN7
CN8
24V
12V
DRW1
CN9
CN10
LINE
OUT
MIC
IN
KIT-7000
-PUSB-QM
Provided
Provided
KIT-7000
-2COM-QM
Not provided
Not provided
Provided
Not provided
Conforming to USB1.1 or USB2.0 (supplying +12V)
Provided
Not provided
Conforming to USB1.1 or USB2.0 (supplying +24V)
D-sub 9pin, female (supplying +5V/+12V)
Box, 10-pin header (supplying +5V/+12V)
Used for a printer (supplying +5V/+24V) (Not used)
Used for an additional FAN (+12V) (Not mounted)
Used for connecting the RISER PC board (68 pins)
Used for the LIU (supplying +12V) (Not used)
Provided
Provided
Provided
Provided
Not provided
Provided
Provided
Provided
Provided
Provided
Not provided
Not provided
Not provided
Not provided
Description
Used for a microphone
Used for an external speaker (with built-in amplifier)
Used for a drawer which is not equipped with +24V drive circuit
(Not used)
3- 6
3. DETAILED INFORMATION OF EACH PC BOARD
EO10-12027
3.3 S.CROSS-IO PC Board
(2) Block Diagram
MIC IN
AC'97
(VT1616)
DRW1
CN10
LINE OUT CN9
Drive Circuit
DRW1
CN8
RISER PC BOARD
USB0
12V P-USB1
(USB0)
CN2
USB1
12V P-USB2
(USB1)
CN3
USB2
12V P-USB3
(USB2)
CN4
USB3
24V P-USB1
(USB3)
CN5
COM5
CN1
COM6 (Header)
CN12
+12V
+12V
(LIU PWR) CN7
+24V
+24V
(PRT PWR) CN6
+12V
FAN
CN13
(3) I/O board specifications
• Audio interface:
AC97 interface, which is connected from the ENGINE PC board via the RISER PC board, is converted to
AC’97 CODEC (VIA’s VT1616).
Input/Output terminal:
LINE OUT terminal (stereo mini jack)
MIC IN terminal (MONO mini jack)
(4) Drawer interface: (for Japan model only, not used for overseas model)
• TOSHIBA TEC standard, 4-pin type connector
• A drawer, which is not equipped with 24V drive circuit, is connectable.
(5) Powered USB: Host controller contained in VT8235 (South Bridge)
• With the above USB host controller, the 4 out of 6 USB1.1/2.0 ports are connectable via the RISER PC
board.
• The 4 Powered USB ports with the addition of 12V/24V power supply are available.
• Windows® 2000 and Windows® XP are supported.
• It is not possible to connect/disconnect the cables to/from the Powered USB while the system is on.
3- 7
3. DETAILED INFORMATION OF EACH PC BOARD
EO10-12027
3.3 S.CROSS-IO PC Board
(6) Serial interface: COM5, COM6 (10-pin header)
• Controller:
POS gate array (EC-B171) mounted on the ENGINE PC board
Controlled by the ENGINE PC board via the RISER PC board.
• Driver/Receiver: Mounted on the ENGINE PC board
• Available port:
1 port (COM5: D-SUB 9-pin, female)
The option KIT-7000-COM-QM is required for using COM6.
3- 8