Download dtk-dp4p installation instructions

DTK-DP4P INSTALLATION INSTRUCTIONS
LOW VOLTAGE POWER,DATA AND VIDEO PROTECTION
NOTE: THIS DEVICE IS NOT INTENDED FOR DIRECT EXPOSURE THE ELEMENTS. USE A NEMA 4X
OR SIMILAR ENCLOSURE FOR OUTDOOR INSTALLATIONS.
1. CHECK THE POWER, DATA AND CABLE SIGNALS BEFORE INSTALLATION OF THE DTK-DP4P TO VERIFY
NO SIGNAL DISTORTION.
2. POWER DOWN OR DISCONNECT THE CIRCUITS THIS DEVICE WILL CONNECT TO BEFORE
BEGINNING INSTALLATION.
3. SECURELY MOUNT THIS UNIT BETWEEN THE FIELD WIRING AND THE EQUIPMENT TO BE PROTECTED.
FOR MOUNTING, USE DOUBLE-SIDED TAPE OR TWO #8 SCREWS (PROVIDED).
4. NOTE: ALLOW THE SURGE PROTECTOR REACTION TIME BY PROVIDING 3-6 WIRE FEET OF CONDUCTOR
LENGTH BETWEEN THE DTK- UNIT AND THE EQUIPMENT TO BE PROTECTED.
5. NOTE: ALLOW FOR THE WIRE DISTANCE FROM THE SURGE PROTECTOR TO PROTECTED EQUIPMENT
TO BE GREATER THAN THE WIRE DISTANCE FROM THE SURGE PROTECTOR TO GROUND.
6. FOR GROUND CONNECTION: CONNECT A MINIMUM # 14 AWG WIRE FROM THE GROUND CONNECTOR
TO THE COMMON EARTH GROUND WITH 25 OHMS OR LESS (5 OHMS IS PREFERRED). USE ONE COMMON
GROUND PER SYSTEM TO ELIMINATE THE POSSIBILITY OF A DIFFERENCE IN GROUND POTENTIALS.
7. FOR VIDEO PROTECTION: CONNECT THE UNPROTECTED VIDEO CABLE INPUT FROM THE FIELD TO
THE BNC IN. CONNECT ONE END OF A SECOND VIDEO CABLE FROM THE BNC OUT THEN CONNECT
THE OTHER END OF THIS CABLE TO THE EQUIPMENT TO BE PROTECTED.
8. FOR DATA PROTECTION: CONNECT THE SUPPLY WIRE FROM THE FIELD TO THE UNPROTECTED
5V DATA TERMINALS MARKED IN . THE SUPPLY WIRE FROM THE PROTECTED 5V DATA TERMINALS
MARKED OUT CONNECTS TO THE EQUIPMENT TO BE PROTECTED.
9. FOR 24VAC POWER PROTECTION: CONNECT THE SUPPLY WIRE FOR THE 24VAC POWER SUPPLY TO
THE UNPROTECTED 24V PWR TERMINALS MARKED IN.
THE SUPPLY WIRE FROM THE PROTECTED TERMINALS MARKED OUT CONNECTS TO THE EQUIPMENT
TO BE PROTECTED.
10. AFTER ALL CONNECTIONS HAVE BEEN MADE AND NO HAZARDS EXIST, RESTORE POWER.
11. CHECK THE POWER, DATA AND CABLE SIGNALS AFTER INSTALLATION OF THE DTK-DP4P TO INSURE
PROPER INSTALL AND NO SIGNAL DISTORTION.
12. FOR FURTHER INFORMATION OR TECHNICAL SUPPORT, PLEASE CAL 1-888-472-6100
CAMERA END
VIDEO SIGNAL
OUT
DATA SIGNAL
IN
VIDEO SIGNAL
PROTECTED
BNC CONNECTOR
VIDEO OUTPUT
VIDEO
UNPROTECTED
GND
DTK-DP4P
DATA SIGNAL
5V DATA
PROTECTED
UNPROTECTED
BNC CONNECTOR
VIDEO INPUT
OUT
5V DATA
IN
5V DATA
5V DATA
24V PWR
24V PWR
OUT
IN
VIDEO
24V PWR
GND
CONTROL END
VIDEO SIGNAL
OUT
DATA SIGNAL
DTK-DP4P
IN
VIDEO SIGNAL
UNPROTECTED
GND
DTK-DP4P
DATA SIGNAL
5V DATA
MATRIX
SWITCHER
5V DATA
PROTECTED
24V POWER,
5V DATA
CONNECTION
OUTPUTS
5V DATA
5V DATA
24V PWR
24V PWR
AUTO IRIS
OPEN CLOSE
OUT
PAN &
TILT
IN
180
5V DATA
5V DATA
5V DATA
24V PWR
24V PWR
OUT
24V PWR
AUTO FOCUS
NEAR
FAR
PRESET 1
PRESET 2
U
N
P
R
O
T
E
C
T
E
D
5V DATA
P
R
O
T
E
C
T
E
D
VIDEO
GROUND
CONNECTOR
24V POWER,
5V DATA
CONNECTION
INPUTS
IN
ZOOM
LOCK
TIME
AUTO
CAMERA
MONITOR
PRESET 3
PRESET 4
PRESET
AUTOPAN
WASH
WIPE
AUX
ALARM
MATRIX KEYBOARD
OUT TO CAMERA
REV
Diversified Technology Group, Inc. 1
ONE DITEK CENTER
1720 Starkey Road, Largo Fl. 33771
1-800-753-2345
www.ditekcorp.com
2
DATE:
DESCRIPTION/ECN:
CHANGED DRAWING
CHANGED INSTRUCTIONS
DRAWN BY:
APP. BY:
09-12-03
JM
05-11-04
JM
DATE:
RWM
9-12-03
TITLE:
INSTALLATION INSTRUCTIONS FOR DTK-DP4P
DWG NO.
INT-100007-001
REV.
PART NO.
191440
2