* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download RTD/resistance input two-wire/three
Nanogenerator wikipedia , lookup
Power dividers and directional couplers wikipedia , lookup
Wien bridge oscillator wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Oscilloscope history wikipedia , lookup
Lego Mindstorms wikipedia , lookup
Phase-locked loop wikipedia , lookup
Power electronics wikipedia , lookup
Analog-to-digital converter wikipedia , lookup
Wilson current mirror wikipedia , lookup
Negative-feedback amplifier wikipedia , lookup
Integrating ADC wikipedia , lookup
Current mirror wikipedia , lookup
Valve audio amplifier technical specification wikipedia , lookup
Flip-flop (electronics) wikipedia , lookup
Immunity-aware programming wikipedia , lookup
Operational amplifier wikipedia , lookup
Transistor–transistor logic wikipedia , lookup
Valve RF amplifier wikipedia , lookup
Schmitt trigger wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Radio transmitter design wikipedia , lookup
Transmitters: TT230 Series TT231 RTD/resistance input two-wire/three-wire transmitter BOTTOM VIEW (INPUT SIDE) TOP VIEW (OUTPUT SIDE) 1 2 5 6 Platinum RTD or Resistance Input Local Power Supply w/ Sourced Output H 2 4-WIRE 3-WIRE 2-WIRE 5 – 1 IN+ 3 4 7 8 IN– 3 + R LOAD I SINKING INPUT CARD 24V DC + LOCAL – – SUPPLY C L Loop-Powered w/ Sinking Output 114.5 mm (4.51 in.) SIDE VIEW USB Configured C 8 I 7 4 ADD JUMPER (2-WIRE ONLY) + 6 + 6 I 5 – I P 24VDC + RCV + – DCS/PLC SOURCING INPUT CARD 12.5 mm (0.50 in.) 99.0 mm (3.90 in.) 100 ohm Pt RTD or 0-900 ohm input ◆ 4-20mA output (sink/source) ◆ 12-32V DC loop/local power Advanced signal processing capabilities, variable range input, and convenient USB programming make this instrument a very versatile temperature measurement device. These transmitters can withstand harsh industrial environments and operate reliably across a wide temperature range with very low drift. They feature RFI, EMI, ESD, EFT, and surge protection plus low radiated emissions. Description The TT231 model is a space-saving two-wire transmitter that converts a 100 ohm Platinum RTD sensor input to a proportional 4-20mA signal. Power is received from the output loop current or a DC supply when using a three-wire connection. The transmitter provides sensor excitation plus performs linearization, lead-wire compensation, and lead-break detection. Key Features & Benefits Setup and calibration are fast and easy with a convenient USB connection to your PC and Acromag’s Windows configuration software. TT230 Series Transmitter Configuration Software is downloadable (FREE) from www.acromag.com. Tel 248-295-0880 Bulletin #8400-660 ■ Fax 248-624-9234 ■ [email protected] ■ www.acromag.com ■ ■ Easy setup and digital calibration via USB with Windows configuration software ■ Flexible RTD or linear resistance input ranges (any 100 ohm Pt RTD with 375-393 alpha) ■ Space-saving 12.5mm (0.5 inch) unit with pluggable terminals for convenient wiring ■ High accuracy, linearity, stability, and reliability ■ Advanced analog signal conditioning ASIC eliminates digitization errors ■ Low temperature drift (<80ppm/°C) ■ Supports sink or source output wiring ■ Programmable over/under-range limits ■ Selectable upscale or downscale operation for sensor errors and lead-break detection ■ NAMUR-compliant output loop current ■ Shock (50g) and vibration (5g) resistant ■ Mounts on Type T DIN-rail ■ Wide ambient operation (-40 to 80°C) ■ CE compliant. UL/cUL Class 1 Div 2 Zone 2 approvals (pending) 30765 Wixom Rd, Wixom, MI 48393 USA Transmitters: TT230 Series TT231 RTD/resistance input two-wire/three-wire transmitter Performance Specifications IMPORTANT: To prevent damage or errors from grounded PCs and surges, Acromag strongly recommends use of their USB-ISOLATOR when configuring a TT230 Series transmitter. ■ USB Interface USB Connector USB Mini-B type socket, 5-pin. USB Data Rate 12Mbps. USB v1.1 and 2.0 compatible. USB Transient Protection Transient voltage suppression on power and data lines. USB Cable Length 5.0 meters maximum. Driver Not required. Uses built-in Human Interface Device (HID) USB drivers of the Windows operating system. ■ Input Default Configuration 100 Pt RTD, α=0.00385 //°C, 0-200°C input, 4-20mA output, upscale break detection. Input Configuration Two-, three- or four-wire sensor input connections. Input Ranges 100 ohm Platinum RTD, alpha = 375-393, 385 (default), -50 to 900°C (-58 to 1652°F). 0 to 900 ohms linear resistance. Programs in °C, °F, or ohmic integer values only. Zero Adjust RTD 3/4 wire: -50, -17.78, or 0°C (-58, 0, 32°F). RTD 2 wire: 0°C (32°F) fixed. RES: 0 or 100 ohms. Full-Scale Adjust RTD: up to 900°C (1652°F), 50°C (58°F) span minimum. Resistance: up to 900 ohms, 8 ohm span minimum. Excitation Current 0.5mA, nominal, each ± lead. Lead-Wire Compensation 25 ohms per lead. Lead Break (Sensor Burnout) Detection Configurable for either upscale or downscale. Input Filter Bandwidth -3dB at 700Hz, typical, normal mode filter. Tel 248-295-0880 ■ Fax 248-624-9234 ■ ■ Output Output Range 4 to 20mA DC. Under-scale limit adjustable for 2.1 to 3.6mA, nominal. Over-scale limit adjustable for 21 to 30mA, nominal. Output Fault Limits (Sensor Fault) 0.4mA below selected under-scale threshold and 1.0mA above over-scale threshold, typical. Output Compliance RLOAD = (VSUPPLY - 8.6V) / 0.020A. RLOAD = 0 to 750 ohms @ 24V DC. Output Accuracy Better than ±0.1% of span, typical for spans less than 500°C. Includes the effects of repeatability, terminal point conformity, and linearization, but does not include sensor error. Ambient Temperature Effect Better than ±0.008% per °C of input span or ±80ppm/°C, typical. Includes the combined effects of zero and span drift over temperature. Output Response Time (for step input change) 500µS, typical with 250 ohm load (to reach 98% of final output value). ■ Physical General General-purpose enclosure designed for mounting on 35mm “T-type” DIN rail. Case Material Self-extinguishing polyamide, UL94 V-0 rated, color light gray. General-purpose NEMA Type 1 enclosure. I/O Connectors Removable plug-in terminal blocks rated for 12A/250V; AWG #26-12, stranded or solid copper wire. Dimensions 12.5 x 114.5 x 99.0 mm (0.5 x 4.51 x 3.90 inches). Shipping Weight 0.22 kg (0.5 pounds) packed. ■ Environmental Operating temperature -40 to 80°C (-40° to 176°F). Storage temperature -40 to 85°C (-40 to 185°F). Relative humidity 5 to 95% non-condensing. Power Requirement 9-32V DC SELV (Safety Extra Low Voltage), 30mA max. Shock and Vibration Immunity Vibration: 5g, per IEC 60068-2-64. Shock: 50g, per IEC 60068-2-27. Electromagnetic Compatibility (EMC) Compliance Radiated Emissions: BS EN 61000-6-4, CISPR 16. RFI: BS EN 61000-6-2, IEC 61000-4-3. Conducted RFI: BS EN 61000-6-2, IEC 61000-4-6. ESD: BS EN 61000-6-2, IEC 61000-4-2. EFT: BS EN 61000-6-2, IEC 61000-4-4. Surge Immunity: BS EN 61000-6-2, IEC 61000-4-5. Approvals CE compliant. UL/cUL listing pending. Designed for Class I; Division 2; Groups ABCD; Zone 2 TT230-Config/Cal Factory custom configuration/calibration service. Specify input type, input/output zero and full-scale values, filtering, and sensor fault settings on order. [email protected] ■ www.acromag.com Ordering Information Models TT231-0600 Transmitter, RTD/resistance input. Services Software TTC-SIP (recommend one kit per customer) Software Interface Package for Acromag TT Series transmitters. Includes configuration software CD-ROM (5040-944), isolator (USB-ISOLATOR) and two USB cables (4001-112, 4001-113). Accessories See www.acromag.com for more information. USB-ISOLATOR USB-to-USB isolator, includes USB cable (4001-112). ■ 30765 Wixom Rd, Wixom, MI 48393 USA All trademarks are property of their respective owners. Copyright © Acromag, Inc. 2012. Data subject to change without notice. Printed in USA 9/2012