* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download 5100-C Digital Output Module Datasheet
Survey
Document related concepts
Flip-flop (electronics) wikipedia , lookup
PID controller wikipedia , lookup
Immunity-aware programming wikipedia , lookup
Variable-frequency drive wikipedia , lookup
Current source wikipedia , lookup
Integrating ADC wikipedia , lookup
Control system wikipedia , lookup
Voltage regulator wikipedia , lookup
Two-port network wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Schmitt trigger wikipedia , lookup
Control theory wikipedia , lookup
Power electronics wikipedia , lookup
Buck converter wikipedia , lookup
Solar micro-inverter wikipedia , lookup
Wilson current mirror wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Transcript
25 South Street Hopkinton, MA 01748 Phone: 508.435.9595 Fax: 508.435.2373 www.ctc-control.com Data Sheet 5100-C Digital Output Module DO 24VDC C 8 Digital Output +24 VDC Sourcing Sourcing Description ! Eight +24 VDC sourcing digital outputs (internal PNP transistor to +24VDC) ! High current: 375 mA per output / 3 A per module ! Individual LED status indicator for each input 5100-C Specifications Parameter General Status Indicator Isolation rating Model type 8 +24 VDC sourcing 1 LED per output 500 VDC 5120 Description PNP transistor to +24VDC of the 5100 controller. Each output has a red LED that is located on the field side on the control circuit. The minimum isolation voltage between the I/O and the CPU circuitry. Identifier for the hardware and software type Performance Output Current: - Note 1 IOH per channel IOH per module 375 mADC 3 ADC IOH per controller 3 ADC ILEAK per channel Output Voltage: Minimum VOH Maximum VOL 100 µADC Output Response Time 0.100 mSec 22 VDC 0 VDC The maximum ‘ON’ current that any given output can source. The maximum current that all the outputs of a module can source at a given time. The maximum current that all the outputs of the controller can source at a given time. The maximum leakage current with the output in the ‘OFF’ state. The minimum ‘ON’ voltage at full load (Vsupply = 24VDC). The maximum ‘OFF’ voltage, 10KΩ resistor to +24VRET. The maximum time duration between when the module receives the command from the 5100 main processor and when the output signal changes. Environmental Temperature o 0 to 50 C Operating Refer to the 5100 Controller Data Sheet for proper mounting instructions. o -25 to 85 C Storage 1. With proper mounting as described in the Model 5100 Controller Data Sheet Copyright © 2002 Control Technology Corporation All Rights Reserved. Printed in USA Data Sheet: 5100-C Digital Output Module Number of outputs Output type Value Doc. No. 5120-C-DS-02.doc Revision: 02 Page 1 of 2 DO 24VDC Data Sheet 5100-C Digital Output Module C 8 Digital Outputs 25 South Street Hopkinton, MA 01748 Phone: 508.435.9595 Fax: 508.435.2373 www.ctc-control.com +24 VDC Sourcing Sourcing Application Information Module Identification Typical Application DO 24VDC C 8 Digital Outputs Sourcing Data Sheet: 5100-C Digital Output Module TO 5100 CONTROLLER DOUT1 TB1-2 + - 24VRET TB2-1 TO 5100 CONTROLLER DOUT1 TB1-2 24VRET TB2-1 1 2 3 4 5 6 7 8 RELAY COIL 5 1 0 0 CPU SNUBBING DIODE (1N4004 OR EQ.) 1 2 3 4 5 TB1 1 2 3 4 5 TB2 SOLID STATE INPUT (EX. NPN TRANSISTOR INPUT) INPUT DIG. GND. CURRENT LIMITING RESISTOR I/O Terminations +24VDC TB1-1 TB1-2 LED1 Dout #1 TB1-3 LED3 Dout #3 TB1-4 LED5 Dout #5 TB1-5 LED7 Notes 1. 2. 3. 4. 5. Dout #7 +24VRET TB2-1 TB2-2 LED2 Dout #2 TB2-3 LED4 Dout #4 TB2-4 LED6 Dout #6 TB2-5 LED8 Dout #8 If an output is used to drive transistor loads, proper current limiting must be observed. If an output is used to drive inductive loads, inductive kicks must be limited via high-speed diodes and/or equivalent devices. When a digital device is powered via an external power source, it may be necessary to tie the ground of this power source to the module’s 24V ground (+24VRET). The total combined output current for the module must not exceed 300 mA (assuming proper mounting as described in the Model 5100 Controller Data Sheet). For register and programming information, refer to the Model 5100 Applications Guide. The information in this document is subject to change without notice. Any software described in this document is provided under license agreement and may be used or copied only in accordance with the terms of the license agreement. The information, drawings, and illustrations contained herein are the property of Control Technology Corporation. No part of this manual may be reproduced or distributed by any means, electronic or mechanical, for any purpose other than the purchaser’s personal use, without the express written consent of Control Technology Corporation. Doc. No. 5120-C-DS-02.doc Revision: 02 Page 2 of 2 Copyright © 2002 Control Technology Corporation All Rights Reserved. Printed in USA