Download Datasheet - Albalá Ingenieros

FRS3000C01
TL3000 TERMINAL LINE
SD-SDI DIGITAL VIDEO TO CCVS ANALOG COMPOSITE VIDEO CONVERTER WITH SD-SDI
AND CCVS FRAME SYNCHRONIZER
Features
• SD-SDI digital video frame synchronizer with composite
video encoder.
• Includes:
- One black-burst reference input with loop-through.
- One SD-SDI input.
- Two synchronized or delayed SD-SDI outputs.
- One or two composite video outputs generated from
the SD-SDI output.
- One TTL-level output with duty cycle proportional to the
video signal delay.
• Operates in frame synchronizer and delay modes.
• Can operate as a line or as a frame synchronizer when
the input signal fails.
• Can be configured to deliver a black signal or to freeze
the last correct frame when the input signal is lost.
• Allows adjustment of luminance, chrominance and
black levels.
• Performs complete EDH packet processing.
• Provides two adjustment modes for the subcarrier
phase: track and fixed SCH.
• Front panel indicators for the SDI input, SDI format and
reference locking.
• 12 bit internal signal processing.
• Provides two user-configurable GPI inputs or outputs.
• Module control and supervision can be done remotely
when the mounting frame is equipped with a
communications controller module.
• One UR3000 mounting frame can house up to 12
FRS3000C01 modules. If power supply redundancy is
required and FA3000 or FA3001 modules are used then
only 10 modules can be housed in the mounting frame.
If PSU3300 or PSU3301 modules are used for this
purpose then up to 12 modules can be installed.
• One UR3100 mounting frame can house up to three
FRS3000C01 modules.
• Low power
Specifications
SD-SDI digital video signal input
Connector
Impedance
Return loss
Input return loss when bypass is
active
Output protected with bypass
relay
Number of inputs
Equalizable cable length:
Belden 8281
SD-SDI digital video signal output
Connector
Impedance
Return loss
Output return loss when bypass
is active
Input to output bypass insertion
loss
Number of outputs
Amplitude
Rise and fall time (20 % - 80 %)
SD-SDI digital video signal
Signal format
Bit rate
Input to output delay
Analog video signal output
Connector
Impedance
Return loss
Signal format
BNC
75Ω ± 1 %
> 15dB up to 270 MHz
> 15dB up to 270 MHz
Yes
1
> 250 m
BNC
75Ω ± 1 %
> 15dB up to 270 MHz
> 15dB up to 270 MHz
< 0.1dB up to 270 MHz
2
800mVpp ± 10 %
1.1 ns typ.
According to SMPTE ST 259
standard
270Mbit/s
1.2us min. in delayer mode
BNC
75Ω ± 1 %
> 40dB at fsc
According to ITU-R BT.470-6,
PAL B/G y NTSC M
2
< 50 mV
Number of outputs
DC voltage
Analog video signal
Differential gain
0.1 %
Differential phase
0.1 º
Chrominance to luminance
delay
< 2.5 ns
S/N ratio unweigthed with
> 65dB RMS from 40Hz to
ref=0.7VRMS
6 MHz
Video digital to analog converter
Sampling rate
27 MHz
Number of bits
10
Input to output delay
3.6us min. in delayer mode
Video delay output (TTL signal)
Connector
BNC
Impedancia
75 Ω
Voltage levels with loaded output:
VOL max.
0.5 V
VOH min.
2.0 V
Encoding
Duty cycle proportional to delay
Period
1 frame
Black-burst reference signal input
Connector
BNC
Return loss
> 40dB at fsc
Type
Passive Loop-Through
Signal format
According to ITU-R BT.470-6
standard
Ordering information
FRS3000C01
SD-SDI digital video to CCVS analog composite video
converter with SD-SDI and CCVS frame synchronizer
Accepted formats
Input signal amplitude
GPI input
Connector
Type
Number of inputs
Activation
Allowed voltage range
GPO output
Connector
Type
Number of outputs
Allowed voltage range
General
Maximum power supply current
Operating temperature range
Approximate weight
625i50, 525i59.94
300mVpp ± 6 dB
Plug-in terminal,
3.81mm pitch
100 kΩ pull-up to 5 V
2
Closing contact to ground
0 .. 24 V
Plug-in terminal,
3.81mm pitch
Open/closed NPN transistor
collector
2
0 .. 24V 50mA max.
+ 350 / - 420 mA
0 .. 50 ºC
375 g
Albalá Ingenieros, S.A.
Medea, 4 - 28037 Madrid
Spain
+34 913274453
www.albalaing.com
[email protected]
20160526 - © Albalá Ingenieros S.A. - Albalá Ingenieros reserves the right to change these specifications without previous notice