Download TRANSISTOR - Introduction

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Mains electricity wikipedia , lookup

Control system wikipedia , lookup

Ohm's law wikipedia , lookup

Signal-flow graph wikipedia , lookup

Thermal runaway wikipedia , lookup

Flip-flop (electronics) wikipedia , lookup

Alternating current wikipedia , lookup

Rectifier wikipedia , lookup

Resistive opto-isolator wikipedia , lookup

Tube sound wikipedia , lookup

Voltage regulator wikipedia , lookup

Power electronics wikipedia , lookup

Current source wikipedia , lookup

Buck converter wikipedia , lookup

P–n diode wikipedia , lookup

Amplifier wikipedia , lookup

Schmitt trigger wikipedia , lookup

Switched-mode power supply wikipedia , lookup

TRIAC wikipedia , lookup

Power MOSFET wikipedia , lookup

Two-port network wikipedia , lookup

Metadyne wikipedia , lookup

Opto-isolator wikipedia , lookup

Current mirror wikipedia , lookup

History of the transistor wikipedia , lookup

Transistor wikipedia , lookup

Transcript
TRANSISTOR - Introduction
BIPOLAR JUNCTION TRANSISTOR
(BJT)
Introduction
• Beside diodes, the most popular semiconductor devices is transistors. Eg:
Bipolar Junction Transistor (BJT)
• Transistors are more complex and can be used in many ways
• Most important feature: can amplify signals and as switch
• Amplification can make weak signal strong (make sounds louder and signal
levels greater), in general, provide function called Gain
Transistor Structure
•
•
•
BJT is bipolar because both holes (+) and electrons (-) will take part in the current
flow through the device
– N-type regions contains free electrons (negative carriers)
– P-type regions contains free holes (positive carriers)
2 types of BJT
– NPN transistor
– PNP transistor
The transistor regions are:
– Emitter (E) – send the carriers into the base region and then on to the
collector
– Base (B) – acts as control region. It can allow none,some or many carriers to
flow
– Collector (C) – collects the carriers
PNP and NPN transistor
structure
P
N
N
P
P
N
Ic(mA)
IB(µA)
IC(mA)
IB(µA)
IE(mA)
Arrow shows the current flows
IE(mA)
NPN Transistor Structure
The collector is lightly doped.
N
C
The base is thin and
is lightly doped.
P
B
The emitter is heavily doped.
N
E
Transistor configuration
•
•
Transistor configuration –is a connection of transistor to get variety operation.
3 types of configuration:
– Common Collector.
– Common Base.
– Common Emitter
Common-Collector Configuration
 The input signal is applied to the base terminal and the output is taken
from the emitter terminal.
• Collector terminal is common to the input and output of the circuit
• Input – BC
• Output – EC
• Input = Output
Common-Base Configuration
•
•
•
•
Base terminal is a common point for input and output.
Input – EB
Output – CB
Not applicable as an amplifier because the relation between input current gain (IE)
and output current gain (IC) is approximately 1
Common-Emitter Configuration
•
•
•
•
Emitter terminal is common for input and output circuit
Input – BE
Output – CE
Mostly applied in practical amplifier circuits, since it provides good voltage, current
and power gain
NPN Transistor Bias
No current flows.
The C-B junction
is reverse biased.
N
C
P
B
N
E
NPN Transistor Bias
The B-E junction
is forward biased.
Current flows.
N
C
P
B
N
E
NPN Transistor Bias
IC
Current flows
everywhere.
When both junctions
are biased....
Note that IB is smaller
than IE or IC.
N
C
P
B
N
E
IB
IE
Note: when the
switch opens, all
currents go to zero.
IC
Although IB is smaller
it controls IE and IC.
N
C
P
B
N
E
IB
Gain is something small
controlling something large
(IB is small).
IE
IC = 99 mA
The current gain from
base to collector
is called b.
IB = 1 mA
b =
99
ICmA
1IBmA
= 99
IE = 100 mA
C
P
B
N
E
IC = 99 mA
Kirchhoff’s
current law:
IB = 1 mA
C
P
B
N
E
IE = I B + I C
= 1 mA + 99 mA
= 100 mA
IE = 100 mA
IC = 99 mA
In a PNP transistor,
holes flow from
emitter to collector.
IB = 1 mA
Notice the PNP
bias voltages.
C
B
E
IE = 100 mA
NPN Schematic Symbol
Collector
Base
C
B E
Emitter
Memory aid: NPN
means Not Pointing iN.
PNP Schematic Symbol
Collector
Base
C
B E
Emitter
Recall: NPN and PNP Bias
•
Fundamental operation of pnp transistor and npn transistor is similar except for:
–
role of electron and hole,
–
voltage bias polarity, and
–
Current direction
•
I-V Characteristic for CE configuration : Input
characteristic
Input characteristic: input
current (IB) against input
voltage (VBE) for several output
voltage (VCE)
• From the graph
– IB = 0 A
– IB = value
VBE < 0.7V (Si)
VBE > 0.7V (Si)
• The transistor turned on when
VBE = 0.7V
I-V Characteristic for CE configuration : Output
characteristic
• Output characteristic: output
current (IC) against output
voltage (VCE) for several
input current (IB)
• 3 operating regions:
– Saturation region
– Cut-off region
– Active region
I-V Characteristic for CE configuration :
Output characteristic
•
Saturation region – in which both junctions are forward-biased and IC increase
linearly with VCE
•
Cut-off region – where both junctions are reverse-biased, the IB is very small, and
essentially no IC flows, IC is essentially zero with increasing VCE
•
Active region – in which the transistor can act as a linear amplifier, where the BE
junction is forward-biased and BC junction is reverse-biased. IC increases drastically
although only small changes of IB.
•
Saturation and cut-off regions – areas where the transistor can operate as a switch
•
Active region – area where transistor operates as an amplifier
Current Relationships
•
•
•
•
•
•
Relations between IC and IE :
α = IC
IE
Value of α usually 0.9998 to 0.9999, α ≈ 1
Relations between IC and IB :
β = IC @ IC = βIB
IB
Value of β usually in range of 50 400
The equation, IE =IC + IB can also written in β
IC = βIB
IE = βIB + IB => IE = (β + 1)IB
The current gain factor , α and β is:
α= β @ β= α .
β+1
α-1