Download semiconductor technical data

Order this document
by CNY17–1/D
SEMICONDUCTOR TECHNICAL DATA
[CTR = 40 – 80%]
GlobalOptoisolator
[CTR = 63 – 125%]
[CTR = 100 – 200%]
The CNY17–1, CNY17–2 and CNY17–3 devices consist of a gallium
arsenide infrared emitting diode optically coupled to a monolithic silicon
phototransistor detector.
*Motorola Preferred Devices
• Closely Matched Current Transfer Ratio (CTR) to Minimize Unit–to–Unit Variation
STYLE 1 PLASTIC
• Guaranteed 70 Volt V(BR)CEO Minimum
• To order devices that are tested and marked per VDE 0884 requirements, the
suffix ”V” must be included at end of part number. VDE 0884 is a test option.
Applications
• Feedback Control Circuits, Open Loop Gain Control in Power Supplies
6
• Interfacing and coupling systems of different potentials and impedances
STANDARD THRU HOLE
CASE 730A–04
• General Purpose Switching Circuits
• Monitor and Detection Circuits
MAXIMUM RATINGS (TA = 25°C unless otherwise noted)
Rating
1
SCHEMATIC
Symbol
Value
Unit
INPUT LED
1
6
Reverse Voltage
VR
6
Volts
2
5
Forward Current — Continuous
IF
60
mA
3
4
IF(pk)
1.5
A
PD
120
mW
1.41
mW/°C
Forward Current — Pk (PW = 1 µs, 330 pps)
LED Power Dissipation @ TA = 25°C
with Negligible Power in Output Detector
Derate above 25°C
OUTPUT TRANSISTOR
Collector–Emitter Voltage
VCEO
70
Volts
Emitter–Base Voltage
VEBO
7
Volts
Collector–Base Voltage
VCBO
70
Volts
Collector Current — Continuous
IC
100
mA
Detector Power Dissipation @ TA = 25°C
with Negligible Power in Input LED
Derate above 25°C
PD
150
mW
1.76
mW/°C
VISO
7500
Vac(pk)
Total Device Power Dissipation @ TA = 25°C
Derate above 25°C
PD
250
2.94
mW
mW/°C
Ambient Operating Temperature Range(2)
TA
– 55 to +100
°C
Tstg
– 55 to +150
°C
TL
260
°C
PIN 1.
2.
3.
4.
5.
6.
LED ANODE
LED CATHODE
N.C.
EMITTER
COLLECTOR
BASE
TOTAL DEVICE
Isolation Surge Voltage(1)
(Peak ac Voltage, 60 Hz, 1 sec Duration)
Storage Temperature Range(2)
Soldering Temperature (10 sec, 1/16″ from case)
1. Isolation surge voltage is an internal device dielectric breakdown rating.
1. For this test, Pins 1 and 2 are common, and Pins 4, 5 and 6 are common.
2. Refer to Quality and Reliability Section in Opto Data Book for information on test conditions.
Preferred devices are Motorola recommended choices for future use and best overall value.
GlobalOptoisolator is a trademark of Motorola, Inc.
REV 1
Optoelectronics
Device Data
Motorola
Motorola, Inc.
1995
1
ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted)(1)
Characteristic
Symbol
Min
Typ
Max
Unit
VF
—
—
—
1.35
1.5
1.25
1.65
—
—
Volts
Reverse Leakage Current (VR = 6 V)
IR
—
—
10
µA
Capacitance (V = 0, f = 1 MHz)
CJ
—
18
—
pF
INPUT LED
Forward Voltage (IF = 60 mA)
TA = 25°C
TA = –55°C
TA = 100°C
OUTPUT TRANSISTOR
Collector–Emitter Dark Current
(VCE = 10 V, TA = 25°C)
CNY17–1,2
CNY17–3
ICEO
—
—
5
5
50
100
nA
(VCE = 10 V, TA = 100°C)
All devices
ICEO
—
1.6
—
µA
ICBO
—
0.5
—
nA
Collector–Emitter Breakdown Voltage (IC = 1 mA)
V(BR)CEO
70
120
—
Volts
Collector–Base Breakdown Voltage (IC = 100 µA)
V(BR)CBO
70
120
—
Volts
Emitter–Base Breakdown Voltage (IE = 100 µA)
V(BR)EBO
7
7.8
—
Volts
DC Current Gain (IC = 2 mA, VCE = 5 V) (Typical Value)
hFE
—
400
—
—
Collector–Emitter Capacitance (f = 1 MHz, VCE = 0)
CCE
—
8
—
pF
Collector–Base Capacitance (f = 1 MHz, VCB = 0)
CCB
—
21
—
pF
Emitter–Base Capacitance (f = 1 MHz, VEB = 0)
CEB
—
8
—
pF
IC (CTR)(2)
4 (40)
6.3 (63)
10 (100)
6 (60)
10 (100)
15 (150)
8 (80)
12.5 (125)
20 (200)
mA (%)
VCE(sat)
—
0.18
0.4
Volts
Delay Time (IF = 10 mA, VCC = 5 V, RL = 75 Ω, Figure 11)
td
—
1.6
5.6
µs
Rise Time (IF = 10 mA, VCC = 5 V, RL = 75 Ω, Figure 11)
tr
—
1.6
4
µs
Storage Time (IF = 10 mA, VCC = 5 V, RL = 75 Ω, Figure 11)
ts
—
0.7
4.1
µs
Fall Time (IF = 10 mA, VCC = 5 V, RL = 75 Ω, Figure 11)
tf
—
2.3
3.5
µs
Delay Time
(IF = 20 mA, VCC = 5 V, RL = 1 kΩ)(3)
(IF = 10 mA, VCC = 5 V, RL = 1 kΩ)(3)
td
CNY17–1
CNY17–2,3
—
—
1.2
1.8
5.5
8
Rise Time
(IF = 20 mA, VCC = 5 V, RL = 1 kΩ)(3)
(IF = 10 mA, VCC = 5 V, RL = 1 kΩ)(3)
CNY17–1
CNY17–2,3
—
—
3.3
5
4
6
Storage Time
(IF = 20 mA, VCC = 5 V, RL = 1 kΩ)(3)
(IF = 10 mA, VCC = 5 V, RL = 1 kΩ)(3)
CNY17–1
CNY17–2,3
—
—
4.4
2, 7
34
39
Fall Time
(IF = 20 mA, VCC = 5 V, RL = 1 kΩ)(3)
(IF = 10 mA, VCC = 5 V, RL = 1 kΩ)(3)
CNY17–1
CNY17–2,3
—
—
9.7
9.4, 20
20
24
Collector–Base Dark Current (VCB = 10 V)
COUPLED
Output Collector Current
(IF = 10 mA, VCE = 5 V)
CNY17–1
CNY17–2
CNY17–3
Collector–Emitter Saturation Voltage (IC = 2.5 mA, IF = 10 mA)
Isolation Voltage (f = 60 Hz, t = 1 sec)(4)
µs
µs
tr
µs
ts
µs
tf
VISO
7500
—
—
Vac(pk)
Isolation Resistance (V = 500 V)(4)
RISO
1011
—
—
Ω
Isolation Capacitance (V = 0, f = 1 MHz)(4)
CISO
—
0.2
0.5
pF
1.
2.
3.
4.
2
Always design to the specified minimum/maximum electrical limits (where applicable).
Current Transfer Ratio (CTR) = IC/IF x 100%.
For test circuit setup and waveforms, refer to Figure 11.
For this test, Pins 1 and 2 are common, and Pins 4, 5 and 6 are common.
Motorola Optoelectronics Device Data
2
VF, FORWARD VOLTAGE (VOLTS)
PULSE ONLY
PULSE OR DC
1.8
1.6
1.4
TA = –55°C
1.2
25°C
100°C
1
1
10
100
IF, LED FORWARD CURRENT (mA)
1000
I C , OUTPUT COLLECTOR CURRENT (NORMALIZED)
TYPICAL CHARACTERISTICS
10
NORMALIZED TO:
IF = 10 mA
1
0.1
0.01
0.1
IF = 10 mA
10
8
6
5 mA
4
2
0
2 mA
1 mA
1
0
2
3
4
5
6
7
8
9
10
VCE, COLLECTOR–EMITTER VOLTAGE (VOLTS)
I C , OUTPUT COLLECTOR CURRENT (NORMALIZED)
IC, COLLECTOR CURRENT (mA)
12
50 100
1
2
5
10
20
IF, LED INPUT CURRENT (mA)
7
5
NORMALIZED TO TA = 25°C
2
1
0.7
0.5
0.2
0.1
–60
–40
–20
0
20
40
60
80
100
TA, AMBIENT TEMPERATURE (°C)
Figure 3. Collector Current versus
Collector–Emitter Voltage
Figure 4. Output Current versus
Ambient Temperature
100
NORMALIZED TO:
VCE = 10 V
TA = 25°C
103
VCE = 70 V
50
30 V
20
102
t, TIME (µs)
ICEO, COLLECTOR–EMITTER DARK CURRENT (NORMALIZED)
0.5
Figure 2. Output Current versus Input Current
Figure 1. LED Forward Voltage versus Forward Current
14
0.2
10 V
101
VCC = 5 V
10
RL = 1000
5
RL = 100
100
{
{
0
20
40
60
80
TA, AMBIENT TEMPERATURE (°C)
Figure 5. Dark Current versus
Ambient Temperature
Motorola Optoelectronics Device Data
100
1
0.1
tr
tf
tr
2
10–1
tf
0.2
0.5
1
2
5
10
20
IF, LED INPUT CURRENT (mA)
50 100
Figure 6. Rise and Fall Times
CNY17–1 and CNY17–2
3
100
100
20
RL = 1000
10
VCC = 5 V
50
VCC = 5 V
t off , TURN–OFF TIME ( µ s)
t on, TURN–ON TIME ( µs)
50
100
5
10
2
70
RL = 1000
10
5
100
10
2
1
0.1
0.2
0.5
1
2
5
10
IF, LED INPUT CURRENT (mA)
20
1
0.1
50 100
0.2
1
2
5
10
IF, LED INPUT CURRENT (mA)
20
50
100
Figure 8. Turn–Off Switching Times
CNY17–1 and CNY17–2
20
4
IF = 0
IB = 8 µA
18
7 µA
16
3
6 µA
5 µA
4 µA
2
3 µA
2 µA
1
1 µA
0
2
4
6
8
10
12
14
16
18
VCE, COLLECTOR–EMITTER VOLTAGE (VOLTS)
20
C, CAPACITANCE (pF)
IC ,TYPICAL COLLECTOR CURRENT (mA)
Figure 7. Turn–On Switching Times
0.5
f = 1 MHz
14
12
10
CCB
CCE
8
CEB
6
4
2
0
0.5
0.1
Figure 9. DC Current Gain (Detector Only)
0.2
0.5
1
2
5
V, VOLTAGE (VOLTS)
20
50
WAVEFORMS
VCC = 5 V
IC
10
Figure 10. Capacitances versus Voltage
TEST CIRCUIT
IF
CLED
INPUT PULSE
RL = 100 Ω
10%
OUTPUT PULSE
INPUT
90%
OUTPUT
td
ts
tr
ton
tf
toff
Figure 11. Switching Time Test Circuit and Waveforms
4
Motorola Optoelectronics Device Data
PACKAGE DIMENSIONS
–A–
6
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
4
–B–
1
3
F 4 PL
C
N
–T–
L
K
SEATING
PLANE
J 6 PL
0.13 (0.005)
G
M
E 6 PL
D 6 PL
0.13 (0.005)
M
T A
B
M
M
T B
M
M
A
M
DIM
A
B
C
D
E
F
G
J
K
L
M
N
INCHES
MIN
MAX
0.320
0.350
0.240
0.260
0.115
0.200
0.016
0.020
0.040
0.070
0.010
0.014
0.100 BSC
0.008
0.012
0.100
0.150
0.300 BSC
0_
15 _
0.015
0.100
STYLE 1:
PIN 1.
2.
3.
4.
5.
6.
MILLIMETERS
MIN
MAX
8.13
8.89
6.10
6.60
2.93
5.08
0.41
0.50
1.02
1.77
0.25
0.36
2.54 BSC
0.21
0.30
2.54
3.81
7.62 BSC
0_
15 _
0.38
2.54
ANODE
CATHODE
NC
EMITTER
COLLECTOR
BASE
CASE 730A–04
ISSUE G
–A–
6
4
–B–
1
S
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3
F 4 PL
L
H
C
–T–
G
J
K 6 PL
E 6 PL
0.13 (0.005)
D 6 PL
0.13 (0.005)
M
T A
M
B
M
SEATING
PLANE
T B
M
A
M
CASE 730C–04
ISSUE D
Motorola Optoelectronics Device Data
M
DIM
A
B
C
D
E
F
G
H
J
K
L
S
INCHES
MIN
MAX
0.320
0.350
0.240
0.260
0.115
0.200
0.016
0.020
0.040
0.070
0.010
0.014
0.100 BSC
0.020
0.025
0.008
0.012
0.006
0.035
0.320 BSC
0.332
0.390
MILLIMETERS
MIN
MAX
8.13
8.89
6.10
6.60
2.93
5.08
0.41
0.50
1.02
1.77
0.25
0.36
2.54 BSC
0.51
0.63
0.20
0.30
0.16
0.88
8.13 BSC
8.43
9.90
*Consult factory for leadform
option availability
5
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
–A–
6
4
–B–
1
3
L
N
F 4 PL
C
–T–
SEATING
PLANE
G
J
K
DIM
A
B
C
D
E
F
G
J
K
L
N
INCHES
MIN
MAX
0.320
0.350
0.240
0.260
0.115
0.200
0.016
0.020
0.040
0.070
0.010
0.014
0.100 BSC
0.008
0.012
0.100
0.150
0.400
0.425
0.015
0.040
MILLIMETERS
MIN
MAX
8.13
8.89
6.10
6.60
2.93
5.08
0.41
0.50
1.02
1.77
0.25
0.36
2.54 BSC
0.21
0.30
2.54
3.81
10.16
10.80
0.38
1.02
D 6 PL
E 6 PL
0.13 (0.005)
M
T A
M
B
M
*Consult factory for leadform
option availability
CASE 730D–05
ISSUE D
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit,
and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different
applications. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does
not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in
systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of
the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such
unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless
against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part.
Motorola and
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.
How to reach us:
USA / EUROPE: Motorola Literature Distribution;
P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447
JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, Toshikatsu Otsuki,
6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–3521–8315
MFAX: [email protected] – TOUCHTONE (602) 244–6609
INTERNET: http://Design–NET.com
HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
6
◊
*CNY17-1/D*
Motorola Optoelectronics CNY17–1/D
Device Data