Download Analog Devices Welcomes Hittite Microwave Corporation

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Three-phase electric power wikipedia , lookup

Immunity-aware programming wikipedia , lookup

Phone connector (audio) wikipedia , lookup

Chirp spectrum wikipedia , lookup

Ground loop (electricity) wikipedia , lookup

Alternating current wikipedia , lookup

Ground (electricity) wikipedia , lookup

Flip-flop (electronics) wikipedia , lookup

Rectifier wikipedia , lookup

Resistive opto-isolator wikipedia , lookup

Mains electricity wikipedia , lookup

Variable-frequency drive wikipedia , lookup

Bode plot wikipedia , lookup

Integrating ADC wikipedia , lookup

Buck converter wikipedia , lookup

Analog-to-digital converter wikipedia , lookup

Utility frequency wikipedia , lookup

Wien bridge oscillator wikipedia , lookup

Power electronics wikipedia , lookup

Heterodyne wikipedia , lookup

Schmitt trigger wikipedia , lookup

Metadyne wikipedia , lookup

Phase-locked loop wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Microwave wikipedia , lookup

Opto-isolator wikipedia , lookup

Transcript
Analog Devices Welcomes
Hittite Microwave Corporation
NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
www.analog.com
www.hittite.com
THIS PAGE INTENTIONALLY LEFT BLANK
HMC361S8G / 361S8GE
v06.1008
FREQUENCY DIVIDERS & DETECTORS - SMT
6
SMT GaAs HBT MMIC
DIVIDE-BY-2, DC - 10 GHz
Typical Applications
Features
Prescaler for DC to X Band PLL Applications:
Ultra Low SSB Phase Noise: -148 dBc/Hz
• Satellite Communication Systems
Wide Bandwidth
• Fiber Optic
Output Power: 3 dBm
• Point-to-Point and Point-to-Multi-Point Radios
Single DC Supply: +5V
• VSAT
S8G SMT Package
Functional Diagram
General Description
The HMC361S8G & HMC361S8GE are low noise
Divide-by-2 Static Dividers with InGaP GaAs HBT
technology in 8 lead surface mount plastic packages.
This device operates from DC (with a square wave
input) to 10 GHz input frequency with a single +5V
DC supply. The low additive SSB phase noise of -148
dBc/Hz at 100 kHz offset helps the user maintain good
system noise performance.
Electrical Specifi cations, TA = +25° C, 50 Ohm System, Vcc= 5V
Parameter
Conditions
Maximum Input Frequency
Minimum Input Frequency
Input Power Range
Output Power
Reverse Leakage
SSB Phase Noise (100 kHz offset)
Output Transition Time
Sine Wave Input.
Min.
Typ.
10
11
[1]
0.2
Max.
GHz
0.5
GHz
Fin = 1 to 8 GHz
-15
+10
dBm
Fin = 8 to 10 GHz
-10
+2
dBm
Fin = 6 GHz
0
Fin = 10 GHz
-6
3
dBm
dBm
Both RF Outputs Terminated
45
dB
Pin = 0 dBm, Fin = 6 GHz
-148
dBc/Hz
Pin = 0 dBm, Fout = 882 MHz
100
ps
83
mA
Supply Current (Icc)
1. Divider will operate down to DC for square-wave input signal.
6-2
Units
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC361S8G / 361S8GE
v06.1008
SMT GaAs HBT MMIC
DIVIDE-BY-2, DC - 10 GHz
20
10
10
Recommended
Operating Window
-10
0
Min Pin +25 C
Max Pin +25 C
Min Pin +85 C
Max Pin +85 C
Min Pin -40 C
Max Pin -40 C
-10
-20
-20
-30
-30
0
1
2
3
4
5
6
7
8
9
10
11 12
0
13
1
2
3
10
6
7
8
9
10
11 12
13
0
8
+25 C
+85 C
-40 C
6
SSB PHASE NOISE (dBc/Hz)
OUTPUT POWER (dBm)
5
SSB Phase Noise
Performance, Pin= 0 dBm, T= 25 °C
Output Power vs. Temperature
4
2
-20
-40
-60
-80
-100
0
-120
-2
-140
-4
0
2
4
6
8
10
12
14
-160
2
10
3
4
10
INPUT FREQUENCY (GHz)
10
5
6
10
7
10
10
OFFSET FREQUENCY (Hz)
Output Harmonic
Content, Pin= 0 dBm, T= 25 °C
Reverse Leakage, Pin= 0 dBm, T= 25 °C
0
0
Pfeedthru
3rd Harmonic
-10
-10
POWER LEVEL (dBm)
OUTPUT LEVEL (dBm)
4
INPUT FREQUENCY (GHz)
INPUT FREQUENCY (GHz)
FREQUENCY DIVIDERS & DETECTORS - SMT
20
0
6
Input Sensitivity Window vs. Temperature
INPUT POWER (dBm)
INPUT POWER (dBm)
Input Sensitivity Window, T= 25 °C
-20
-30
-40
-50
Both Output Ports Terminated
One Output Port Terminated
-20
-30
-40
-50
0
2
4
6
8
INPUT FREQUENCY (GHz)
10
12
0
2
4
6
8
10
12
14
INPUT FREQUENCY (GHz)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
6-3
HMC361S8G / 361S8GE
v06.1008
Output Voltage Waveform,
Pin= 0 dBm, Fout= 882 MHz, T= 25 °C
Absolute Maximum Ratings
500
300
AMPLITUDE (mV)
FREQUENCY DIVIDERS & DETECTORS - SMT
6
SMT GaAs HBT MMIC
DIVIDE-BY-2, DC - 10 GHz
100
-100
-300
-500
22.7
23.1
23.5
23.9
24.3
RF Input (Vcc = +5V)
+13 dBm
Vcc
+5.5V
VLogic
Vcc -1.6V to Vcc -1.2V
Junction Temperature (TJ)
135 °C
Continuous Pdiss (T = 85 °C)
(derate 15.9 mW/°C above 85 °C)
0.79 W
Thermal Resistance (RTH)
(junction to ground paddle)
63 °C/W
Storage Temperature
-65 to +150 °C
Operating Temperature
-40 to +85 °C
24.7
TIME (nS)
Typical Supply Current vs. Vcc
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Vcc (V)
Icc (mA)
4.75
74
5.0
83
5.25
89
Note: Divider will operate over full voltage range shown above
Outline Drawing
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS].
3. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE.
4. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE.
5. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO
PCB RF GROUND.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
HMC361S8G
Low Stress Injection Molded Plastic
Sn/Pb Solder
MSL1
HMC361S8GE
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL1
Package Marking [3]
[1]
H361
XXXX
[2]
H361
XXXX
[1] Max peak reflow temperature of 235 °C
[2] Max peak reflow temperature of 260 °C
[3] 4-Digit lot number XXXX
6-4
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC361S8G / 361S8GE
v06.1008
SMT GaAs HBT MMIC
DIVIDE-BY-2, DC - 10 GHz
Pin Number
Function
Description
1
OUT
Divided output 180° out of phase with pin 3.
2, 6
N/C
No connection. These pins must not be grounded.
3
OUT
Divided Output.
4
VCC
Supply voltage 5V ± 0.25V.
5
IN
RF Input must be DC blocked.
7
IN
RF Input 180° out of phase with pin 5 for differential operation.
A/C ground for single ended operation
8
GND
Ground Backside of package has exposed metal ground slug which
must be connected to ground.
Interface Schematic
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
FREQUENCY DIVIDERS & DETECTORS - SMT
6
Pin Description
6-5
HMC361S8G / 361S8GE
v06.1008
FREQUENCY DIVIDERS & DETECTORS - SMT
6
Evaluation PCB
List of Materials for Evaluation PCB 104631 [1]
Item
Description
J1 - J3
PCB Mount SMA RF Connector
C1 - C4
100 pF Capacitor, 0402 Pkg.
C5
1000 pF Capacitor, 0603 Pkg.
C6
10 μF Tantalum Capacitor
U1
HMC361S8G / HMC361S8GE Divide-by-2
PCB [2]
104627 Eval Board
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350
6-6
SMT GaAs HBT MMIC
DIVIDE-BY-2, DC - 10 GHz
The circuit board used in the final application should
use RF circuit design techniques. Signal lines
should have 50 ohm impedance while the package
ground leads and backside ground slug should be
connected directly to the ground plane similar to that
shown. A sufficient number of via holes should be
used to connect the top and bottom ground planes.
The evaluation circuit board shown is available
from Hittite upon request. This evaluation board is
designed for single ended input testing. J2 and J3
provide differential output signals.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC361S8G / 361S8GE
v06.1008
SMT GaAs HBT MMIC
DIVIDE-BY-2, DC - 10 GHz
6
FREQUENCY DIVIDERS & DETECTORS - SMT
Application Circuit
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
6-7