Download mav11sm.

Amplifier
print this page
MAV-11SM
Frequency
GAIN, dB Maximum Power, dBm Dynamic Range VSWR
MHz
Output
Input
NF
(1 dB
(no
dB
Comp.)
damage)
Typ.
50-1000
9.00
+17.50
+13.00
3.60
Lw=low range(fL to fU/2) U=upper range(fU/2 to fU)
fL - fU
Min.
Absolute
Maximum
Rating
DC Power
Thermal
resistance
Øjc
IP3
CurIn Out I
P
dBm
rent Device Volt(V.) °C/W
Typ. Typ. (mA) (mW)
Typ.
(mA)
30.00 1.50 1.70 80.00 550.00 60.00
5.50
125.00
Notes:
gain at highest frequency. Full temperature range, except room
• Minimum
temperature for Dash-4 models.
resistance Øjc is from hottest junction in the device to the
• Thermal
mounting surface of the leads.
• Model number designated by alphanumeric code marking.
damage may occur if any of these limits are exceeded. These
• Permanent
ratings are not intended for continuous normal operation.
Amplifier Selection Guide, please click here.
• For
For Amplifier Environmental Specifications, please click here.
Surface Mount Environmental Specifications, please click here.
• For
Re-flow soldering information is available in "Surface Mount" article.
• Low frequency cutoff determined by external coupling capacitors.
• Frequency at which output power, NF and IP3 are specified: 500 MHz.
• Typical Biasing Configuration ERA/MAR/MAV/RAM/VAM
Pin Connections
Port RF in RF Out DC Case GND Not Used
cb
1
3
3
2,4
-
Case Style - RRR137 (inch,mm ) weight: 0.015 grams.
A
B
C
D
E
F
G
H
J
.28
.14 .030 .020 .145 .110 .006 .010 .030
7.112 3.556 0.762 0.508 3.683 2.794 0.152 0.254 0.762
K
L
M
N
P
Q
R
S
T
• Prefix letter (optional) designates assembly location.
voltage must be connected to pin 3 through a bias resistor in order
• Supply
to prevent damage. See Biasing MMIC Amplifiers. Reliability predictions
are applicable at specified current and normal operating conditions.
Tolerance: .x ± .1 .xx ± .03 .xxx ± .015 inch.
Material and Finish:
Case material: plastic. Lead finish: tin-lead plate or tin
plate.
• Aqueous washable.
Quality Control Procedures and Environmental Specifications are
• General
given in Mini- Circuits Guarantees Quality.
Hi-Rel, MIL description are given in Hi-Rel and MIL
• Prices and Specifications subjects to change without notice.
Marking:
Typical Performance Data
S11 (Input Return S 21 (Power S12 (Isolation
S22 (Output
Loss)
Gain)
Out-in)
Return Loss)
dB Mag Ang
dB
Ang
dB Mag Ang dB Mag Ang
0.50
0.76 -22.00 19.30 167.00
0.06 54.00
0.77 -22.00
26.85
24.40
26.85
5.00
0.20 -79.00 13.70 164.00
0.15 12.00
0.21 -83.00
37.95
16.50
38.38
50.00
0.04 -75.00 12.70 174.00
0.15 2.00
0.05
37.50
16.40
42.67
136.00
100.00
0.04 -81.00 12.60 171.00
0.15 2.00
0.05
38.17
16.40
42.73
137.00
500.00
0.09
12.10 141.00
0.16 6.00
0.15
41.87
124.00
15.80
43.17
144.00
1000.00
0.18
10.70 106.00
0.18 6.00
0.26
44.14
161.00
14.70
44.76
173.00
1500.00
0.28 171.00 9.10 77.00
0.21 2.00
0.35 163.00
44.66
13.50
44.24
2000.00
0.37 149.00 7.60 52.00
0.22 -5.00
0.43 140.00
43.46
13.00
42.92
2500.00
0.45 133.00 6.10 33.00
0.23
0.47 125.00
42.48
12.70
10.00 41.94
3000.00
0.52 118.00 4.60 14.00
0.23
0.50 112.00
41.44
12.60
16.00 40.98
FREQ
(MHz)
RF output is identified by index mark, model dash number
by alphanumeric code.
Special Tolerances:
Lead width ±.010 inch; lead thickness ±.003 inch.
Packaging:
Packaging information:
Tape Width(mm): 12
Reel Size(inches): 7
Device Cavity Pitch(mm): 8
Devices Per Reel: 500