Download TSOP582.., TSOP584.. IR Receiver Modules for Remote Control

TSOP582.., TSOP584..
www.vishay.com
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
FEATURES
• Low supply current
• Photo detector and preamplifier in one package
• Internal filter for PCM frequency
• Improved shielding against EMI
• Supply voltage: 2.5 V to 5.5 V
• Improved immunity against ambient light
19026
• Insensitive to supply voltage ripple and noise
• Material categorization:
for definitions of compliance please see
www.vishay.com/doc?99912
MECHANICAL DATA
Pinning for TSOP582.., TSOP584..:
DESCRIPTION
1 = OUT, 2 = GND, 3 = VS
These products are miniaturized IR receiver modules for
infrared remote control systems. A PIN diode and a
preamplifier are assembled on a leadframe, the epoxy
package contains an IR filter.
The demodulated output signal can be directly connected to
a microprocessor for decoding.
The TSOP582.. and TSOP584.. are optimized to suppress
almost all spurious pulses from energy saving lamps like
CFLs. The AGC4 used in the TSOP584.. may suppress
some data signals. The TSOP582.. is a legacy product for all
common IR remote control data formats. Between these
two receiver types, the TSOP584.. is preferred. Customers
should initially try the TSOP584.. in their design.
These components have not been qualified according to
automotive specifications.
PARTS TABLE
LEGACY, FOR LONG BURST REMOTE CONTROLS
(AGC2)
RECOMMENDED FOR LONG
BURST CODES (AGC4) (1)
30 kHz
TSOP58230
TSOP58430
33 kHz
TSOP58233
TSOP58433
36 kHz
TSOP58236
TSOP58436 (2)(3)(4)
38 kHz
TSOP58238
TSOP58438 (5)(6)
40 kHz
TSOP58240
TSOP58440
56 kHz
TSOP58256
TSOP58456 (7)(8)
AGC
Carrier
frequency
Package
Minicast
Pinning
1 = OUT, 2 = GND, 3 = VS
Dimensions (mm)
5.0 W x 6.95 H x 4.8 D
Mounting
Leaded
Application
Best remote control code
Remote control
(2)
RC-5
(3)
RC-6
(4)
Panasonic
(5)
NEC
(6)
Sharp
(7)
r-step
(8)
Thomson RCA
Note
(1) We advise try AGC4 first if the burst length is unknown
Rev. 1.3, 27-Feb-15
1
Document Number: 82461
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP582.., TSOP584..
www.vishay.com
Vishay Semiconductors
BLOCK DIAGRAM
APPLICATION CIRCUIT
17170-10
16833_14
R1
Transmitter
with
TSALxxxx
3
VS
1
Input
Band
pass
AGC
µC
OUT
Demodulator
VO
GND
GND
The external components R1 and C1 are optional
to improve the robustness against electrical overstress
(typical values are R1 = 100 Ω, C1 = 0.1 µF).
2
PIN
+ VS
C1
Circuit
33 kΩ
IR receiver
Control circuit
ABSOLUTE MAXIMUM RATINGS
PARAMETER
Supply voltage
Supply current
Output voltage
Voltage at output to supply
Output current
Junction temperature
Storage temperature range
Operating temperature range
Power consumption
Soldering temperature
TEST CONDITION
SYMBOL
VS
IS
VO
VS - VO
IO
Tj
Tstg
Tamb
Ptot
Tsd
Tamb ≤ 85 °C
t ≤ 10 s, 1 mm from case
VALUE
-0.3 to +6
5
-0.3 to 5.5
- 0.3 to (VS + 0.3)
5
100
-25 to +85
-25 to +85
10
260
UNIT
V
mA
V
V
mA
°C
°C
°C
mW
°C
Note
• Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability.
ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
Supply voltage
TEST CONDITION
VS = 5 V, Ev = 0
Ev = 40 klx, sunlight
Ev = 0, IR diode TSAL6200,
IF = 250 mA, test signal see fig. 1
IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see fig. 1
Pulse width tolerance:
tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 1
tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 1
Angle of half transmission distance
Supply current
Transmission distance
Output voltage low
Minimum irradiance
Maximum irradiance
Directivity
SYMBOL
VS
ISD
ISH
MIN.
2.5
0.55
TYP.
0.7
0.8
d
MAX.
5.5
0.9
40
m
VOSL
0.2
Ee min.
Ee max.
ϕ1/2
UNIT
V
mA
mA
100
mV
0.4
mW/m2
W/m2
deg
50
± 45
TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
Optical Test Signal
1.0
(IR diode TSAL6200, IF = 0.4 A, 30 pulses, f = f0, t = 10 ms)
tpo - Output Pulse Width (ms)
Ee
t
tpi *
* tpi
VO
Output Signal
16110
1)
7/f0 < td < 15/f0
2) t - 5/f < t < t + 6/f
pi
0
po
pi
0
VOH
VOL
T
10/f0 is recommended for optimal function
td 1)
tpo 2)
Input Burst Length
0.7
0.6
0.5
0.4
0.3
0.2
λ = 950 nm,
Optical Test Signal, Fig.1
0.1
1
10
102
103
104
Ee - Irradiance (mW/m2)
Fig. 1 - Output Active Low
Rev. 1.3, 27-Feb-15
0.8
0
0.1
t
Output Pulse Width
0.9
Fig. 2 - Pulse Length and Sensitivity in Dark Ambient
2
Document Number: 82461
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP582.., TSOP584..
www.vishay.com
Vishay Semiconductors
600 µs
t
600 µs
t = 60 ms
94 8134
Output Signal, (see fig. 4)
VO
VOH
VOL
t off
t on
5.0
Ee min. - Threshold Irradiance (mW/m2)
Optical Test Signal
Ee
Correlation with Ambient Light Sources:
4.5 10 W/m2 = 1.4 kLx (Std. illum. A, T = 2855 K)
10
W/m2 = 8.2 kLx (Daylight, T = 5900 K)
4.0
3.5
2.5
2.0
1.5
1.0
0.5
0
0.01
t
Ee min. - Threshold Irradiance (mW/m2)
ton, toff - Output Pulse Width (ms)
ton
0.6
toff
0.4
0.3
0.2
λ = 950 nm,
optical test signal, Fig. 1
0.1
0
0.1
1
10
100
Ee - Irradiance
10
100
1000
1.0
f = f0
0.9
0.8
0.7
f = 30 kHz
0.6
0.5
f = 20 kHz
0.4
f = 10 kHz
0.3
0.2
0.1
f = 100 Hz
0
1
10 000
10
100
1000
ΔVsRMS - AC Voltage on DC Supply Voltage (mV)
(mW/m2)
Fig. 4 - Output Pulse Diagram
Fig. 7 - Sensitivity vs. Supply Voltage Disturbances
1.2
500
E - Max. Field Strength (V/m)
E e min./Ee - Rel. Responsivity
1
Fig. 6 - Sensitivity in Bright Ambient
0.8
0.5
0.1
Ee - Ambient DC Irradiance (W/m2)
Fig. 3 - Output Function
0.7
Wavelength of Ambient
Illumination: λ = 950 nm
3.0
1.0
0.8
0.6
0.4
f = f0 ± 5 %
Δ f(3 dB) = f0/10
0.2
450
400
350
300
250
200
150
100
50
0.0
0
0.7
16925
0.9
1.1
1.3
0
20747
f/f0 - Relative Frequency
Fig. 5 - Frequency Dependence of Responsivity
Rev. 1.3, 27-Feb-15
500
1000
1500
2000
2500
3000
f - EMI Frequency (MHz)
Fig. 8 - Sensitivity vs. Electric Field Disturbances
3
Document Number: 82461
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP582.., TSOP584..
www.vishay.com
Vishay Semiconductors
0°
0.8
10°
20°
30°
Max. Envelope Duty Cycle
0.7
0.6
40°
0.5
1.0
0.4
TSOP582..
0.3
50°
0.8
60°
TSOP584..
0.2
70°
0.7
0.1
0
0.9
80°
f = 38 kHz, Ee = 2 mW/m²
0
20
40
60
80
100
120
0.6
Burst Length (Number of Cycles/Burst)
19258
0.4
0.2
0
drel - Relative Transmission Distance
Fig. 9 - Max. Envelope Duty Cycle vs. Burst Length
Fig. 12 - Horizontal Directivity
0°
0.40
10°
20°
Ee min. - Sensitivity (mW/m2)
30°
0.35
0.30
40°
0.25
1.0
0.20
0.9
50°
0.8
60°
0.15
0.10
70°
0.7
0.05
80°
0
-30
-10
10
30
50
70
90
0.6
Tamb - Ambient Temperature (°C)
1.0
0.8
0.6
0.4
0.2
850
950
1050
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
1.5
1150
λ - Wavelength (nm)
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
VS - Supply Voltage (V)
Fig. 11 - Relative Spectral Sensitivity vs. Wavelength
Rev. 1.3, 27-Feb-15
0
0.8
1.2
94 8408
0.2
Fig. 13 - Vertical Directivity
Ee min. - Sensitivity (mW/m2)
S (λ)rel - Relative Spectral Sensitivity
Fig. 10 - Sensitivity vs. Ambient Temperature
0
750
0.4
d rel - Relative Transmission Distance
19259
Fig. 14 - Sensitivity vs. Supply Voltage
4
Document Number: 82461
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP582.., TSOP584..
www.vishay.com
Vishay Semiconductors
SUITABLE DATA FORMAT
IR Signal
This series is designed to suppress spurious output pulses
due to noise or disturbance signals. The devices can
distinguish data signals from noise due to differences in
frequency, burst length, and envelope duty cycle. The data
signal should be close to the device’s band-pass center
frequency (e.g. 38 kHz) and fulfill the conditions in the table
below.
When a data signal is applied to the product in the
presence of a disturbance, the sensitivity of the receiver is
automatically reduced by the AGC to insure that no spurious
pulses are present at the receiver’s output.
Some examples which are suppressed are:
0
• DC light (e.g. from tungsten bulbs sunlight)
5
• Continuous signals at any frequency
10
15
20
Time (ms)
16920
Fig. 15 - IR Disturbance from Fluorescent Lamp
with Low Modulation
IR Signal
• Strongly or weakly modulated noise from fluorescent
lamps with electronic ballasts (see figure 15 or figure 16)
0
5
16921
10
15
20
Time (ms)
Fig. 16 - IR Disturbance from Fluorescent Lamp
with High Modulation
TSOP582..
TSOP584..
Minimum burst length
10 cycles/burst
10 cycles/burst
After each burst of length
a minimum gap time is required of
10 to 70 cycles
≥ 12 cycles
10 to 35 cycles
≥ 12 cycles
For bursts greater than
a minimum gap time in the data stream is needed of
70 cycles
> 4 x burst length
35 cycles
> 10 x burst length
Maximum number of continuous short bursts/second
800
1300
NEC code
yes
preferred
RC5/RC6 code
yes
preferred
Thomson 56 kHz code
yes
preferred
Sharp code
yes
preferred
Most common disturbance
patterns are suppressed
Even extreme disturbance
patterns are suppressed
Suppression of interference from fluorescent lamps
Notes
• For data formats with short bursts please see the datasheet of TSOP581.., TSOP583..
• Best choice of AGC for some popular IR-codes:
- TSOP58436: RC-5, RC-6, Panasonic
- TSOP58438: NEC, Sharp, r-step
- TSOP58456: r-step, Thomson RCA
• For SIRCS 15 and 20 bit, Sony 12 bit IR-codes, please see the datasheet for TSOP4S40, TSOP2S40
Rev. 1.3, 27-Feb-15
5
Document Number: 82461
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP582.., TSOP584..
www.vishay.com
Vishay Semiconductors
PACKAGE DIMENSIONS in millimeters
5
4.8
(4)
2.8
(5.55)
6.95 ± 0.3
8.25 ± 0.3
R2
0.9
1.1
30.5 ± 0.5
(1.54)
0.85 max.
0.7 max.
2.54 nom.
2.54 nom.
0.5 max.
1.2 ± 0.2
Marking area
technical drawings
according to DIN
specifications
Not indicated to lerances ± 0.2
Drawing-No.: 6.550-5263.01-4
Issue: 12; 16.04.10
19009
Rev. 1.3, 27-Feb-15
R2
6
Document Number: 82461
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000