Download Reflection - schoolphysics

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Very Large Telescope wikipedia , lookup

XMM-Newton wikipedia , lookup

Optical telescope wikipedia , lookup

Reflecting telescope wikipedia , lookup

Transcript
REFLECTION (Plane mirrors)
You will find details of reflection in the 11-14 section of the site but some basic facts will be
summarised here with a few more advanced topics.
Plane mirror
The reflection of light from a plane mirror can be
summarised by the following laws:
1. The angle of incidence (i) is equal to the angle of
reflection (r)
2. The incident ray, reflected ray and the normal to the
surface at the point of incidence all lie in the same
plane.
incident ray
normal
i
The reflection from a plane (flat) mirror is shown in
Figure 1. Not the normal line and the use of shading to
represent the back of the mirror.
mirror
reflected ray
r
Figure 1
Remember that with a glass mirror the reflecting surface (usually a thin layer of aluminum or
silver) is placed on the back of the mirror and then covered with a protective layer. This means
that although the main reflected image comes form this surface light will also reflect from the
front surface of the glass. This will give a secondary image which is much weaker that the main
image. This is usually invisible in every day life but would create severe problems in astronomy.
For this reason all astronomical mirrors have their reflecting surface formed on the front of the
glass.
Images
There are two types of image
(a) a Real Image
This is one through which the light rays actually pass
and which can be formed on a screen. Examples of
real images are the image formed on the film in a
camera or on the retina of your eye
(b) a Virtual Image
This is one through which the rays do not pass, they
only appear to come from it. Examples of virtual
images are the image formed by a magnifying glass
when used to look at a small object and that in a
plane mirror.
For a real object, the image produced by a plane
mirror is virtual and the same distance (d) behind the
mirror as the object is in front of it. (see Figure 2).
object
d
mirror
d
image
Figure 2
1
Inclined mirrors
If the image of an object is viewed in two plane mirrors that are inclined to each other more than
one image is formed. The number of images depends on the angle between the two mirrors.
Object
Image 2
Image 1
A = 60o
Image 3
Image 4
Figure 3
Image 5
The number of images formed in two plane mirrors inclined at an angle A to each other is given
by the formula:
Number of images = 360/A - 1
Figure 3 shows the case for an angle of 60o between the mirrors. As the angle gets smaller
(down to 0o when the mirrors are facing each other and parallel) the smaller the angle the
greater the number of images.
Try seeing this in a room where there are mirrors on two walls facing each other.

Rotating mirrors
When a mirror rotates through an angle a
beam of light reflected from it will rotate
through an angle of 2. (See Figure 4).
new reflected ray
2A
2

mirror
Figure 4
2
Lateral inversion
The image produced by a plane mirror is laterally inverted - that is reversed left to right. Look at
yourself in a plane mirror and raise your fight hand - your image raises its left hand. In fact what
is actually happening is that the image is reversed back to front.
Uses of plane mirrors
Optical lever
Kaleidoscope
Seeing round corners
Looking into!
Periscope (See Figure 5)
Dental mirror
Telescope flat
Overhead projector
Illuminating Egyptian tombs
Sextant (See: OHT sheets/Sextant)
Reflection properties
When light falls on a surface three things may happen:(a) a fraction r will be reflected
(b) a fraction a will be absorbed and
(c) a fraction t will be transmitted
For any surface these fractions must add up to 1.
Therefore :- r + a + t = 1
mirror
Figure 5
mirror
Magnesium oxide will reflect some 98% of the incident light; silver is also a very good reflector
over a fairly limited range of wavelengths but does tarnish with age and aluminum although not
quite so reflective gives a better reflection over a wider range of wavelengths.
The absorption of light as it passes through a material is very important especially in the area of
fibre optic communication systems (see later).
The intensity (I) of light transmitted through a material of thickness x is given by the equation:
I=I0e-μx
where μ is a constant for the material. For a specimen of glass μ could be 4 m -1 at 600 nm
wavelength yellow light) rising to 1000 m-1 at a wavelength of 250 nm (ultra violet), the larger the
value of m the more the light is absorbed. This means that if a beam of yellow light passed
through 0.1 m of glass it would be reduced to 67% of its original intensity.
The absorption of differing wavelengths as they pass through the Earth's atmosphere is vital in
communications and the transmission of ultra violet light through the "ozone hole"!
Mirrors used for reflecting telescopes are made with front-silvered mirrors to present unwanted
multiple reflections from within the glass and also to reduce absorption within it.
One way mirrors are an interesting application of reflection. A thin metal film is deposited on a
glass sheet so that only part of the incident light is transmitted. Standing on the poorly lit side of
such a minor enables you to see through to the bright side but when viewed from the other side
it looks like a perfect mirror.
3