Download seem 6™ ledtrim flange

seem 6 led trim flange
™
FSM6L-TF
NEW CONSTRUCTION ONLY
configurations are run specific, please consult factory drawings before beginning installation.
focal point
key
parts lists
included hardware
Corner Unit
power off
reflector screw
(72010)
U - individual
power on
joiner bulkhead
screw (72010)
lens tool (A15966-01)
(AFFIXED TO HOUSING. ONE PER RUN)
attention
parts shipped installed
mounting bracket
assembly
S - start of run
joiner bracket
screw
joiner
bracket
(72009)
(A15328-01)
(70001)
flush lens
(17999)
joiner bulkhead
I - intermediate
(A15570-01)
(71025)
drop lens
(18495)
E - end of run
lens end piece
MOUNTING LOCATIONS
A
B
A
start of run/individual
5.625"
142.9mm
5.00"
127mm
A
6.70"
170.27mm
mounting bracket must be secured to structure above.
1/4" - 20 carriage bolt may be supplied by others for
greater adjustability.
(71024)
(A12498)
MOUNTING BRACKET MUST BE
INSTALLED PRIOR TO DRYWALL
(indivudual housings
only up to 8’)
C
A
intermediate/end of run
housing length
A
B
C
2'
3'
4'
5'
6'
7'
8'
1"
1"
6"
6"
6"
6"
6"
21"
33"
35"
47"
59"
71"
83"
22"
34"
36"
48"
60"
72"
84"
mounting location chart is an
approximate guide only.
Luminaires must be installed by a qualified electrician (check with local and national codes for proper installation).
To prevent electrical shock, disconnect electrical supply before installation or servicing.
IS0568 Rev. C 2016 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com
1 of 3
CEILING CUTOUT
ceiling cutout length
=
nominal run length minus 5/16" (+/- 1/16")
example:
5.75" min
12' run length
= 11' 11-3/4" cutout length
6.00" max
corner unit must be assembled
prior to ceiling installation.
1
2
3
5
6
AVOID ALL CONTACT WITH LED SURFACE,
LEDs ARE EASILY DAMAGED!
4
make electrical connections
7
8
REPEAT STEPS 5-7
UNTIL ALL UNITS ARE
IN THE CEILING
tighten luminaire
snug to the ceiling
individual installations
skip to step 11
Luminaires must be installed by a qualified electrician (check with local and national codes for proper installation).
To prevent electrical shock, disconnect electrical supply before installation or servicing.
IS0568 Rev. C 2016 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com
2 of 3
11
11
10
9
make electrical connections
12
14
13
FLUSH LENS
FLUSH LENS
REFERENCE INSTRUCTIONS ON INCLUDED
TOOL FOR LENS INSTALLATION.
secure reflectors to housing
(4 screws per reflector)
EMERGENCY
14
SEE BATTERY MANUFACTURER
INSTRUCTIONS
DROP LENS
emergency battery
maximum mounting height:
18.00'
emergency circuit
maximum mounting height:
21.00'
DRIVER SERVICE
1
2
3
Contractor is responsible for adequately reinforcing walls and/or ceilings to support luminaire weight. Focal Point, LLC accepts no responsibility for inadequately reinforced walls
and/or ceilings. The information contained in this drawing is the sole property of Focal Point, LLC. Any reproduction in part or whole without the written permission of Focal Point, LLC
is prohibited.
IS0568 Rev. C 2016 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com
3 of 3