Download manufactured units reference tables

DIVISION 27 21 29
CNFE4FX2TX2US SERIES –FOUR PORT
UNMANAGED FAST ETHERNET SWITCH
ENGINEERING SPECIFICATIONS
PART 1 - GENERAL
1.01 SUMMARY
A. Four Port Unmanaged Fast Ethernet Switch
1.02 SECTION INCLUDES
A. CNFE4FX2TX2US four port unmanaged fast
Ethernet switch, standalone or rack mountable
1.03 REFERENCES
A. Underwriters Laboratory (UL)
B. Underwriters Laboratory Canada (ULC)
C. European Union Compliance (CE)
1.04 SYSTEM DESCRIPTION
A. Performance Requirements: Provide four Fast
Ethernet ports –two 10/100 ports and two ports,
100 Mbps SFP based
1.05 SUBMITTALS
A. Manufacturer’s Installation and Operating
Manual: Printed installation and operating
information.
1.06 DELIVERY, STORAGE AND HANDLING
A. Store in original packaging in a climate
controlled environment. Storage Temperature
not to exceed: -40˚ C to +85˚ C
1.07 PROJECT/SITE CONDITIONS
A. Temperature Requirements: Products shall
operate in an environment with an ambient
temperature range of –40˚ C to +75˚ C without
the assistance of fan-forced cooling.
B. Humidity Requirements: Products shall operate
in an environment with relative humidity of 0%
to 95% (non-condensing). If product is installed
in condensation conditions, add –C to the part
number.
1.08 WARRANTY
A. Standard Communication Networks
Comprehensive Lifetime Warranty: ComNet
warrants the product to be free of factory defects
under manufacture’s Lifetime Warranty as
submitted under article 1.05
PART 2 - PRODUCTS
2.01 MANUFACTURER
A. Acceptable Manufacturer: Communication
Networks, Inc.; 3 Corporate Drive, Danbury, CT
06810 USA; Telephone: 203-796-5300; Fax
203-796-5303; Email: [email protected];
Internet: www.comnet.com
B. Substitutions: Not Permitted
C. All modules shall be supplied from a single
manufacturer.
2.02 MANUFACTURED UNITS
A. Model Number Descriptions: Reference Table
A: Product Number Descriptions
B. Model Compatibility Chart: Reference Table B:
Product Compatibility Chart
2.03 GENERAL SPECIFICATIONS
A. The Ethernet data switch shall be a ComNet
CNFE4FX2TX2US series module. The module
shall support the transmission of two channels of
10 or 100 Mbps over unshielded twisted pair and
two channels of 100Base FX via single-mode or
multimode fiber. The module shall support the
Ethernet data IEEE 802.3 protocol using Autonegotiating and Auto-MDI/MDI-X features. The
module shall feature two electrical ports and two
optical ports. The module shall require no infield electrical or optical adjustments or in-line
attenuators to ease installation. The module shall
provide power, link speed, simplex or duplex
transmission, and fiber port status indicating
LED’s for monitoring proper system operation.
The modules shall provide automatic re-settable
solid-state current limiters and independent
voltage regulators on each module to reduce the
chance of a single point failure of the system.
The module shall be hot swappable in a rack
mount system to reduce complete system shut
down during maintenance or repair. The module
shall have a lifetime warranty to reduce system
life cycle cost in an event of a module failure.
2.04 DATA SPECIFICATIONS
A. Data Interface: Ethernet IEEE802.3
B. Data Rate: 10/100 Mbps
C. Data Inputs: 2
D. Operation Mode: Simplex or Duplex
2.05 OPTICAL SPECIFICATIONS
A. ComNet Model Number CNFE4FX2TX2US
1. Optical Fiber: 50/125 µm, 62.5/125 µm, or
singlemode
2. Number of Fibers Required: 1 or 2, SFP
dependant
3. Optical Wavelength: SFP-dependant
4. Optical Power Budget: SFP dependant
5. Maximum Distance: SFP dependant
2.06 STATUS INDICATORS
A. Power: On/Green – Off/Off
B. Link/Speed: 100Mbps/Green – 10 Mbps/Red No Fiber Connection/Off
C. Simplex/Duplex: Simplex/Off, Duplex/Green.
2.07 CONNECTORS
A. Optical: LC or SC, SFP dependant
B. Power: Terminal Block with Screw Clamps.
C. Data: RJ-45
2.08 ELECTRICAL SPECIFICATIONS
A. Power: 12VDC @ 800 mA
B. Current Protection: Automatic re-settable solidstate current limiters
C. Voltage Regulation: Solid-state, Independent on
each board
D. Circuit Board: UL 94 flame rated and meets all
IPC standards.
E. Rack mount Card: Shall be hot-swappable with
ComNet Model Number C1 (EIA 19” card cage)
2.09 MECHANICAL SPECIFICATIONS
A. Dimensions: 7.0” x 4.9” x 1.0” (17.80 cm x 12.5
cm x 2.5 cm)
B. Number of Rack Slots: 1
C. Weight: <2.0 lbs./0.9kg
2.10 ENVIRONMENTAL SPECIFICATIONS
A. MTBF: >100,000 Hours
B. Operating Temp: –40˚ C to +75˚ C
C. Storage Temp: -40˚ C to +85˚ C
D. Relative Humidity: 0% to 95% (noncondensing). If product is installed under
condensation conditions, unit shall have
conformal coating applied to the printed circuit
board. (Add –C to model number for conformal
coated printed circuit board)
2.11 REGULATORY AGENCIES/APPROVALS
AND LISTINGS
A. Underwriters Laboratory (UL) Listing
B. Underwriters Laboratory Canada (ULC)
C. UL 94-flame rated PCB board
2.12 ACCESSORIES
A. Card Cage: C1 Model Number C1 (EIA 19” card
cage) shall be available to house and power rack
mount modules.
B. Blank Panels: C1 Model Number C1-BP shall be
available to cover unused rack slots.
PART 3 - EXECUTION
3.01 EXAMINATION
A. All optical connectors shall be covered with dust
caps and remain on the module until installing
cable connectors to module.
3.02 PREPARATION
A. Standalone Module (Surface Mount)
1. Shall be mounted on a properly prepared
surface adequate for the size and weight of
module. The placement of the unit shall
allow provision for cable installation and
maintenance as indicated on the approved
detail drawings and in compliance with the
ComNet mounting template and installation
manual.
B. Rack Mount Module (19” Rack)
1. Shall be installed in the ComNet Model
Number C1 card cage. Ensure the card cage
is installed in a standard EIA 19” (482.6
mm) rack or wall standoff bracket adequate
for the size and weight of the card cage. The
placement of the unit shall allow provision
for cable installation and maintenance as
indicated on the approved detail drawings
and in compliance with the ComNet
installation manual.
C. Optical Fibers
1. Caution: NEVER look into the end of an
active optical fiber when using laser light
output. Eye damage can occur. Wear eye
protection when cleaving, terminating, and
splicing fiber.
2. The number and type (multimode or singlemode) of optical fiber shall meet the
requirements of the ComNet model number
in article 2.05 used in the installation.
3. All optical fiber cables shall be properly
installed and terminated with the mating
optical connectors as submitted in article
2.07 (A).
4. The optical link shall be tested with either a
power meter, at a minimum, or OTDR to
ensure the link budget (overall path loss)
plus an added 3dB of optical safety margin
does not exceed the optical power budget as
submitted in article 2.05.
5. All optical connectors on cable shall be
cleaned in compliance to optical connector
manufactures specifications and covered
with dust caps until connection to the fiber
optic module.
3.03 INSTALLATION
A. General: Locate fiber optic modules as indicated
on the approved detail drawings and install
module in compliance with the ComNet
installation and operations manual.
3.04 TESTING
A. Testing the Fiber Optic Ethernet Link.
1. Verify that the data leads and optical fibers
are properly connected.
2. Make sure that power is applied to all fiber
optic modules, controllers, and receiver
drivers or other equipment used in the
system.
3. Successful data link operation should be
confirmed at this point by communicating
with other equipment.
3.05 CLEANING
A. Follow all instructions for proper use of solvents
and adhesives used for termination and splicing.
B. At completion of the installation, dispose of all
fiber scraps properly.
MANUFACTURED UNITS REFERENCE
TABLES
Table A: Product Number Descriptions
CNFE4FX2TX2US
DESCRIPTION
SERIES
CNFE4FX2TX2US
4-port unmanaged Fast Ethernet switch
Table B: Product Compatibility Chart
TRANSCEIVER
CNFE4FX2TX2US
END OF SECTION
COMPATIBLE REPEATER / TRANSCEIVER
CNFE4FX2TX2US, CNFE4FX4US, CNFE4TX4US
CNFE8FX4TX4US, CNFE8FX8US, CNFE8TX8US
CNFE2MC, CNFE2MC-M, CNFE22MC, CNFE100x
CNGE3FE7MS2, CNGE2FE24MS, CNGE2FE24MS-PoE
DIVISION 27 21 29
CNFE4FX4US SERIES –FOUR PORT
UNMANAGED FAST ETHERNET SWITCH
ENGINEERING SPECIFICATIONS
PART 1 - GENERAL
1.01 SUMMARY
B. Four Port Unmanaged Fast Ethernet Switch
1.02 SECTION INCLUDES
B. CNFE4FX4US four port unmanaged fast
Ethernet switch, standalone or rack mountable
1.03 REFERENCES
D. Underwriters Laboratory (UL)
E. Underwriters Laboratory Canada (ULC)
F. European Union Compliance (CE)
1.04 SYSTEM DESCRIPTION
B. Performance Requirements: Provide four Fast
Ethernet Ethernet ports –four ports, 100 Mbps
SFP based
1.05 SUBMITTALS
B. Manufacturer’s Installation and Operating
Manual: Printed installation and operating
information.
1.06 DELIVERY, STORAGE AND HANDLING
B. Store in original packaging in a climate
controlled environment. Storage Temperature
not to exceed: -40˚ C to +85˚ C
1.07 PROJECT/SITE CONDITIONS
C. Temperature Requirements: Products shall
operate in an environment with an ambient
temperature range of –40˚ C to +75˚ C without
the assistance of fan-forced cooling.
D. Humidity Requirements: Products shall operate
in an environment with relative humidity of 0%
to 95% (non-condensing). If product is installed
in condensation conditions, add –C to the part
number.
1.08 WARRANTY
B. Standard Communication Networks
Comprehensive Lifetime Warranty: ComNet
warrants the product to be free of factory defects
under manufacture’s Lifetime Warranty as
submitted under article 1.05
PART 2 - PRODUCTS
2.01 MANUFACTURER
D. Acceptable Manufacturer: Communication
Networks, Inc.; 3 Corporate Drive, Danbury, CT
06810 USA; Telephone: 203-796-5300; Fax
203-796-5303; Email: [email protected];
Internet: www.comnet.com
E. Substitutions: Not Permitted
F. All modules shall be supplied from a single
manufacturer.
2.02 MANUFACTURED UNITS
C. Model Number Descriptions: Reference Table
A: Product Number Descriptions
D. Model Compatibility Chart: Reference Table B:
Product Compatibility Chart
2.03 GENERAL SPECIFICATIONS
B. The Ethernet data switch shall be a ComNet
CNFE4FX4US series module. The module shall
support the transmission of four channels of
100Base FX via single-mode or multimode fiber.
The module shall feature four optical ports. The
module shall require no in-field electrical or
optical adjustments or in-line attenuators to ease
installation. The module shall provide power,
link speed, simplex or duplex transmission, and
fiber port status indicating LED’s for monitoring
proper system operation. The modules shall
provide automatic re-settable solid-state current
limiters and independent voltage regulators on
each module to reduce the chance of a single
point failure of the system. The module shall be
hot swappable in a rack mount system to reduce
complete system shut down during maintenance
or repair. The module shall have a lifetime
warranty to reduce system life cycle cost in an
event of a module failure.
2.04 DATA SPECIFICATIONS
E. Data Interface: Ethernet IEEE802.3
F. Data Rate: 100 Mbps
G. Data Inputs: 4
H. Operation Mode: Simplex or Duplex
2.05 OPTICAL SPECIFICATIONS
B. ComNet Model Number CNFE4FX4US
6. Optical Fiber: 50/125 µm, 62.5/125 µm, or
singlemode
7. Number of Fibers Required: 1 or 2, SFP
dependant
8. Optical Wavelength: SFP-dependant
9. Optical Power Budget: SFP dependant
10. Maximum Distance: SFP dependant
2.06 STATUS INDICATORS
D. Power: On/Green – Off/Off
E. Link/Speed: 100Mbps/Green – 10 Mbps/Red No Fiber Connection/Off
F. Simplex/Duplex: Simplex/Off, Duplex/Green.
2.07 CONNECTORS
D. Optical: LC or SC, SFP dependant
E. Power: Terminal Block with Screw Clamps.
2.08 ELECTRICAL SPECIFICATIONS
F. Power: 12VDC @ 800 mA
G. Current Protection: Automatic re-settable solidstate current limiters
H. Voltage Regulation: Solid-state, Independent on
each board
I. Circuit Board: UL 94 flame rated and meets all
IPC standards.
J. Rack mount Card: Shall be hot-swappable with
ComNet Model Number C1 (EIA 19” card cage)
2.09 MECHANICAL SPECIFICATIONS
D. Dimensions: 7.0” x 4.9” x 1.0” (17.80 cm x 12.5
cm x 2.5 cm)
E. Number of Rack Slots: 1
F. Weight: <2.0 lbs./0.9kg
2.10 ENVIRONMENTAL SPECIFICATIONS
E. MTBF: >100,000 Hours
F. Operating Temp: –40˚ C to +75˚ C
G. Storage Temp: -40˚ C to +85˚ C
H. Relative Humidity: 0% to 95% (noncondensing). If product is installed under
condensation conditions, unit shall have
conformal coating applied to the printed circuit
board. (Add –C to model number for conformal
coated printed circuit board)
2.11 REGULATORY AGENCIES/APPROVALS
AND LISTINGS
D. Underwriters Laboratory (UL) Listing
E. Underwriters Laboratory Canada (ULC)
F. UL 94-flame rated PCB board
2.12 ACCESSORIES
C. Card Cage: C1 Model Number C1 (EIA 19” card
cage) shall be available to house and power rack
mount modules.
D. Blank Panels: C1 Model Number C1-BP shall be
available to cover unused rack slots.
PART 3 - EXECUTION
3.01 EXAMINATION
B. All optical connectors shall be covered with dust
caps and remain on the module until installing
cable connectors to module.
3.02 PREPARATION
D. Standalone Module (Surface Mount)
2. Shall be mounted on a properly prepared
surface adequate for the size and weight of
module. The placement of the unit shall
allow provision for cable installation and
maintenance as indicated on the approved
detail drawings and in compliance with the
ComNet mounting template and installation
manual.
E. Rack Mount Module (19” Rack)
2. Shall be installed in the ComNet Model
Number C1 card cage. Ensure the card cage
is installed in a standard EIA 19” (482.6
mm) rack or wall standoff bracket adequate
for the size and weight of the card cage. The
placement of the unit shall allow provision
for cable installation and maintenance as
indicated on the approved detail drawings
and in compliance with the ComNet
installation manual.
F. Optical Fibers
6. Caution: NEVER look into the end of an
active optical fiber when using laser light
output. Eye damage can occur. Wear eye
protection when cleaving, terminating, and
splicing fiber.
7. The number and type (multimode or singlemode) of optical fiber shall meet the
requirements of the ComNet model number
in article 2.05 used in the installation.
8. All optical fiber cables shall be properly
installed and terminated with the mating
optical connectors as submitted in article
2.07 (A).
9. The optical link shall be tested with either a
power meter, at a minimum, or OTDR to
ensure the link budget (overall path loss)
plus an added 3dB of optical safety margin
does not exceed the optical power budget as
submitted in article 2.05.
10. All optical connectors on cable shall be
cleaned in compliance to optical connector
manufactures specifications and covered
with dust caps until connection to the fiber
optic module.
3.03 INSTALLATION
B. General: Locate fiber optic modules as indicated
on the approved detail drawings and install
module in compliance with the ComNet
installation and operations manual.
3.04 TESTING
B. Testing the Fiber Optic Ethernet Link.
4. Verify that the data leads and optical fibers
are properly connected.
5. Make sure that power is applied to all fiber
optic modules, controllers, and receiver
drivers or other equipment used in the
system.
6. Successful data link operation should be
confirmed at this point by communicating
with other equipment.
3.05 CLEANING
C. Follow all instructions for proper use of solvents
and adhesives used for termination and splicing.
D. At completion of the installation, dispose of all
fiber scraps properly.
MANUFACTURED UNITS REFERENCE
TABLES
Table A: Product Number Descriptions
CNFE4FX4US SERIES
DESCRIPTION
CNFE4FX4US
4-port unmanaged Fast Ethernet switch
Table B: Product Compatibility Chart
TRANSCEIVER
CNFE4FX4US
END OF SECTION
COMPATIBLE REPEATER / TRANSCEIVER
CNFE4FX4US, CNFE4FX2TX2US, CNFE4TX4US
CNFE8FX4TX4US, CNFE8FX8US, CNFE8TX8US
CNFE2MC, CNFE2MC-M, CNFE22MC, CNFE100x
CNGE3FE7MS2, CNGE2FE24MS, CNGE2FE24MS-PoE
DIVISION 27 21 29
CNFE4TX4US SERIES –FOUR PORT
UNMANAGED FAST ETHERNET SWITCH
ENGINEERING SPECIFICATIONS
PART 1 - GENERAL
1.01 SUMMARY
C. Four Port Unmanaged Fast Ethernet Switch
1.02 SECTION INCLUDES
C. CNFE4TX4US four port unmanaged fast
Ethernet switch, standalone or rack mountable
1.03 REFERENCES
G. Underwriters Laboratory (UL)
H. Underwriters Laboratory Canada (ULC)
I. European Union Compliance (CE)
1.04 SYSTEM DESCRIPTION
C. Performance Requirements: Provide four Fast
Ethernet 10/100 ports
1.05 SUBMITTALS
C. Manufacturer’s Installation and Operating
Manual: Printed installation and operating
information.
1.06 DELIVERY, STORAGE AND HANDLING
C. Store in original packaging in a climate
controlled environment. Storage Temperature
not to exceed: -40˚ C to +85˚ C
1.07 PROJECT/SITE CONDITIONS
E. Temperature Requirements: Products shall
operate in an environment with an ambient
temperature range of –40˚ C to +75˚ C without
the assistance of fan-forced cooling.
F. Humidity Requirements: Products shall operate
in an environment with relative humidity of 0%
to 95% (non-condensing). If product is installed
in condensation conditions, add –C to the part
number.
1.08 WARRANTY
C. Standard Communication Networks
Comprehensive Lifetime Warranty: ComNet
warrants the product to be free of factory defects
under manufacture’s Lifetime Warranty as
submitted under article 1.05
PART 2 - PRODUCTS
2.01 MANUFACTURER
G. Acceptable Manufacturer: Communication
Networks, Inc.; 3 Corporate Drive, Danbury, CT
06810 USA; Telephone: 203-796-5300; Fax
203-796-5303; Email: [email protected];
Internet: www.comnet.com
H. Substitutions: Not Permitted
I. All modules shall be supplied from a single
manufacturer.
2.02 MANUFACTURED UNITS
E. Model Number Descriptions: Reference Table
A: Product Number Descriptions
F. Model Compatibility Chart: Reference Table B:
Product Compatibility Chart
2.03 GENERAL SPECIFICATIONS
C. The Ethernet data switch shall be a ComNet
CNFE4TX4US series module. The module shall
support the transmission of four channels of 10
or 100 Mbps over unshielded twisted pair. The
module shall support the Ethernet data IEEE
802.3 protocol using Auto-negotiating and AutoMDI/MDI-X features. The module shall feature
four electrical ports. The module shall require
no in-field electrical or in-line attenuators to ease
installation. The module shall provide power,
link speed, simplex or duplex transmission, and
fiber port status indicating LED’s for monitoring
proper system operation. The modules shall
provide automatic re-settable solid-state current
limiters and independent voltage regulators on
each module to reduce the chance of a single
point failure of the system. The module shall be
hot swappable in a rack mount system to reduce
complete system shut down during maintenance
or repair. The module shall have a lifetime
warranty to reduce system life cycle cost in an
event of a module failure.
2.04 DATA SPECIFICATIONS
I. Data Interface: Ethernet IEEE802.3
J. Data Rate: 10/100 Mbps
K. Data Inputs: 4
L. Operation Mode: Simplex or Duplex
2.05 STATUS INDICATORS
G. Power: On/Green – Off/Off
H. Link/Speed: 100Mbps/Green – 10 Mbps/Red No Fiber Connection/Off
I. Simplex/Duplex: Simplex/Off, Duplex/Green.
2.06 CONNECTORS
F. Power: Terminal Block with Screw Clamps.
G. Data: RJ-45
2.07 ELECTRICAL SPECIFICATIONS
K. Power: 12VDC @ 800 mA
L. Current Protection: Automatic re-settable solidstate current limiters
M. Voltage Regulation: Solid-state, Independent on
each board
N. Circuit Board: UL 94 flame rated and meets all
IPC standards.
O. Rack mount Card: Shall be hot-swappable with
ComNet Model Number C1 (EIA 19” card cage)
2.09 MECHANICAL SPECIFICATIONS
G. Dimensions: 7.0” x 4.9” x 1.0” (17.80 cm x 12.5
cm x 2.5 cm)
H. Number of Rack Slots: 1
I. Weight: <2.0 lbs./0.9kg
2.10 ENVIRONMENTAL SPECIFICATIONS
I. MTBF: >100,000 Hours
J. Operating Temp: –40˚ C to +75˚ C
K. Storage Temp: -40˚ C to +85˚ C
L. Relative Humidity: 0% to 95% (noncondensing). If product is installed under
condensation conditions, unit shall have
conformal coating applied to the printed circuit
board. (Add –C to model number for conformal
coated printed circuit board)
2.11 REGULATORY AGENCIES/APPROVALS
AND LISTINGS
G. Underwriters Laboratory (UL) Listing
H. Underwriters Laboratory Canada (ULC)
I. UL 94-flame rated PCB board
2.12 ACCESSORIES
E. Card Cage: C1 Model Number C1 (EIA 19” card
cage) shall be available to house and power rack
mount modules.
F. Blank Panels: C1 Model Number C1-BP shall be
available to cover unused rack slots.
PART 3 - EXECUTION
3.01 EXAMINATION
C. All connectors shall be covered with dust caps
and remain on the module until installing cable
connectors to module.
3.02 PREPARATION
G. Standalone Module (Surface Mount)
3. Shall be mounted on a properly prepared
surface adequate for the size and weight of
module. The placement of the unit shall
allow provision for cable installation and
maintenance as indicated on the approved
detail drawings and in compliance with the
ComNet mounting template and installation
manual.
H. Rack Mount Module (19” Rack)
3. Shall be installed in the ComNet Model
Number C1 card cage. Ensure the card cage
is installed in a standard EIA 19” (482.6
mm) rack or wall standoff bracket adequate
for the size and weight of the card cage. The
placement of the unit shall allow provision
for cable installation and maintenance as
indicated on the approved detail drawings
and in compliance with the ComNet
installation manual.
3.03 INSTALLATION
C. General: Locate modules as indicated on the
approved detail drawings and install module in
compliance with the ComNet installation and
operations manual.
3.04 TESTING
C. Testing the Ethernet Link.
7. Verify that the data leads are properly
connected.
8. Make sure that power is applied to all
modules, controllers, and receiver drivers or
other equipment used in the system.
9. Successful data link operation should be
confirmed at this point by communicating
with other equipment.
3.05 CLEANING
E. Follow all instructions for proper use of solvents
and adhesives used for termination and splicing.
MANUFACTURED UNITS REFERENCE TABLES
Table A: Product Number Descriptions
CNFE4TX4US SERIES
DESCRIPTION
CNFE4TX4US
4-port unmanaged Fast Ethernet switch
Table B: Product Compatibility Chart
TRANSCEIVER
CNFE4TX4US
COMPATIBLE REPEATER / TRANSCEIVER
CNFE4TX4US, CNFE4FX4US, CNFE4FX2TX2US
CNFE8FX4TX4US, CNFE8FX8US, CNFE8TX8US
CNFE2MC, CNFE2MC-M, CNFE22MC, CNFE100x
CNGE3FE7MS2, CNGE2FE24MS, CNGE2FE24MS-PoE
END OF SECTION