Survey
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
Download DR40LCM 900 Specification
Document related concepts
no text concepts found
Transcript
LEDDR700MA-1-10V Dimmable Driver for Led Panels 40W , 900mA F 110 M M ■ Features � SELV ■ Applications � � � � � � � � � ■ Description ～ ℃℃ ■ Model Encoding LCM - 40 FROM SOURCE TO SITE ® W - www.orlight.com T - 01923 851 890 E - [email protected] LEDDR700MA-1-10V Dimmable Driver for Led Panels 40W , 900mA SPECIFICATION DR40LCM-900 MODEL Current level selectable via DIP switch, please refer to”DIP SWITCH TABLE” section CURRENT LEVEL OUTPUT 900mA RATED POWER 42W DC VOLTAGE RANGE 2 ~ 45V OPEN CIRCUIT VOLTAGE (max.) 65V CURRENT RIPPLE Note.5 CURRENT TOLERANCE AUXILIARY DC OUTPUT Nominal 12V(deviation 11.4~12.6V)@50mA SETUP TIME 500ms / 230VAC Note.3 VOLTAGE RANGE INPUT Note.2 47 ~ 63Hz POWER FACTOR (Typ.) PF≧0.975/230VAC, PF≧0.96/277VAC @full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section) THD< 20%(@load≧75%) TOTAL HARMONIC DISTORTION (Please refer to “TOTAL HARMONIC DISTORTION(THD)” section) Note.4 91% AC CURRENT (Typ.) 0.23A/230VAC INRUSH CURRENT (Typ.) COLD START 20A(twidth=260μs measured at 50% Ipeak) at 230VAC; Per NEMA 410 MAX. No. of PSUs on 16A CIRCUIT BREAKER 26 units (circuit breaker of type B) / 44 units (circuit breaker of type C) at 230VAC LEAKAGE CURRENT <0.5mA / 240VAC STANDBY POWER CONSUMPTION Note.6 <1W SHORT CIRCUIT Constant current limiting, recovers automatically after fault condition is removed PROTECTION OVER VOLTAGE EMC OTHERS NOTE 0.2A/277VAC 110 ~ 130V Shutdown o/p voltage, re-power on to recover OVER TEMPERATURE Shutdown o/p voltage,re-power on to recover DIMMING Please refer to "DIMMING OPERATION" section FUNCTION SYNCHRONIZATION SAFETY & 180 ~ 295VAC 254 ~ 417VDC (Please refer to "STATIC CHARACTERISTIC" section) FREQUENCY RANGE EFFICIENCY (Typ.) ENVIRONMENT 5.0% max. @rated current ±5% Please refer to "SYNCHRONIZATION OPERATION” section TEMP. COMPENSATION By external NTC, please refer to “TEMPERATURE COMPENSATION OPERATION”section WORKING TEMP. Tcase=-30 ~ +90℃ (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section) MAX. CASE TEMP. Tcase=+90℃ WORKING HUMIDITY 20 ~ 90% RH non-condensing STORAGE TEMP., HUMIDITY -40 ~ +80℃, 10 ~ 95% RH TEMP. COEFFICIENT ±0.03%/℃ (0 ~ 50℃) VIBRATION 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes SAFETY STANDARDS UL8750, CSA C22.2 No.250.13-12, ENEC EN61347-1, EN61347-2-13, EN62384 independent,GB19510.14,GB19510.1 approved WITHSTAND VOLTAGE I/P-O/P:3.75KVAC ISOLATION RESISTANCE I/P-O/P:>100M Ohms / 500VDC / 25℃/ 70% RH EMC EMISSION Note.7 Compliance to EN55015, EN61000-3-2 Class C(@load≧40%) ; EN61000-3-3; GB17625.1,GB17743 EMC IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547, light industry level(surge immunity Line-Line 2KV) MTBF 260.6K hrs min. DIMENSION 123.5*81.5*23mm (L*W*H) PACKING 0.24Kg ; 54pcs/15Kg/1.12CUFT MIL-HDBK-217F (25℃) ℃ ® T - 01923 851 890 E - [email protected] FROM SOURCE TO SITE ~ W - www.orlight.com LEDDR700MA-1-10V Dimmable Driver for Led Panels 40W , 900mA BLOCK DIAGRAM PFC fosc : 60KHz PWM fosc : 80KHz I/P EMI FILTER & RECTIFIERS POWER SWITCHING PFC CIRCUIT O.L.P. PFC CONTROL O.T.P. PWM CONTROL RECTIFIERS +12Vaux RECTIFIERS & FILTER +V -V DIM+ DIM- CURRENT LIMIT DETECTION CIRCUIT O.V.P. DIP SWITCH TABLE DR40LCM-900 is a multiple-stage constant current driver, selection of output current through DIP switch is exhibited below. DIP S.W. 1 2 3 4 5 6 350mA ---- ---- ---- ---- ---- ---- 500mA ON ---- ---- ---- ---- ---- 600mA ON ON ---- ---- ---- ---- 700mA(factory default) ON ON ON ---- ---- ON 900mA ON ON ON ON ---- ON 1050mA ON ON ON ON ON ON Io FROM SOURCE TO SITE ® W - www.orlight.com T - 01923 851 890 E - [email protected] LEDDR700MA-1-10V Dimmable Driver for Led Panels 40W , 900mA DIMMING OPERATION 1 2 TB1 1 2 3 4 5 6 TB3 SYN. 1 CN101 2 3 CN100 4 1 2 TB5 ON 1 2 3 4 5 6 ※ 3 in 1 dimming function �Output constant current level can be adjusted by applying one of the three methodologies between DIM+ and DIM-: 0 ~ 10VDC, or 10V PWM signal or resistance. �Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. �Dimming source current from power supply: 100μA (typ.) ◎ Applying additive 0 ~ 10VDC 100% 90% -V 80% + + - DIM+ + - DIM- Output current (%) +V Additive Voltage 70% 60% 50% 40% 30% 20% 10% 0% “DO NOT connect "DIM- to -V" 0V 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V Dimming input: Additive voltage ◎ Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz): 100% 90% -V 80% + + - - DIM+ Output current (%) +V Additive PWM signal 70% 60% 50% 40% 30% 20% DIM- 10% 0% “DO NOT connect "DIM- to -V" ◎ Applying additive resistance: 0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% Duty cycle of additive 10V PWM signal dimming input 100% 90% -V 80% + - - DIM+ Additive Resistance Output current (%) +V + DIM- 70% 60% 50% 40% 30% 20% 10% “DO NOT connect "DIM- to -V" 0% Short 10K/N 20K/N 30K/N 40K/N 50K/N 60K/N 70K/N 80K/N 90K/N 100K/N (N=driver quantity for synchronized dimming operation ) Dimming input: Additive resistance Note : 1. Min. dimming level is about 6% and the output current is not defined when 0%< I out<6%. 2. The output current could drop down to 0% when dimming input is about 0kΩ or 0Vdc, or 10V PWM signal with 0% duty cycle. 3. Please do not activate”temperature compensation” when performing dimming operation. FROM SOURCE TO SITE ® W - www.orlight.com T - 01923 851 890 E - [email protected] LEDDR700MA-1-10V Dimmable Driver for Led Panels 40W , 900mA SYNCHRONIZATION OPERATION �Synchronization up to 10 drivers (1 master + 9 slaves) �Maximum cable length between each unit : 20 meter. SYN. - - LCM-40 (Slave 1) + + + + LCM-40 (Master) 20m SYN. - - + + SYN. - - LCM-40 (Slave 2) 20m NOTE: Please make sure all units are set to 100% dimming setting(factory default) before synchronizing. TEMPERATURE COMPENSATION OPERATION DR40LCM-900 have the built-in temperature compensation function ; by connecting a temperature sensor (NTC resistor) between the +NTC / -NTC terminal of DR40LCM-900 and the detecting point on the lighting system or the surrounding environment, output current of DR40LCM-900 could be correspondingly changed, based on the sensed temperature, to ensure the long life of LED. NTC derating curve 105 100 Output Current (%) 220KO 220KΩ 95 330KO 330KΩ 470KO 470KΩ 90 85 80 75 70 65 55 60 65 70 75 80 85 90 95 Sensed Temperature(℃) ◎ DR40LCM-900 can still be operated normally when the NTC resistor is not connected and the value of output current will be the current level selected through the DIP switch. ◎ NTC reference: NTC resistance Output Current 220K < 60℃, 100% of the rated current (corresponds to the setting current level) > 60℃, output current begins to reduce, please refer to the curve for details. 330K < 70℃, 100% of the rated current (corresponds to the setting current level) > 70℃, output current begins to reduce, please refer to the curve for details. 470K < 80℃, 100% of the rated current (corresponds to the setting current level) > 80℃, output current begins to reduce, please refer to the curve for details. Notes: 1. MEAN WELL does not offer the NTC resistor and all the data above are measured by using THINKING TTC03 series. 2. If other brands of NTC resistor is applied,please check the temperature curve first. ◎ Dimming and synchronization function of the driver will be invalid when the "temperature compensation" function is in use. FROM SOURCE TO SITE ® W - www.orlight.com T - 01923 851 890 E - [email protected] LEDDR700MA-1-10V Dimmable Driver for Led Panels 40W , 900mA OUTPUT LOAD vs TEMPERATURE 100 others 80 80 60 60 40 LOAD (%) LOAD (%) 100 1050mA 20 -30 -15 0 15 30 40 50 60 70 (HORIZONTAL) 40 20 -30 -25 AMBIENT TEMPERATURE,Ta (℃) 0 20 45 55 65 75 90 (HORIZONTAL) Tcase (℃) STATIC CHARACTERISTIC 100 90 80 LOAD (%) 70 60 50 40 180 190 200 210 220 230 240 250 260 270 280 295 INPUT VOLTAGE (V) 60Hz ※ De-rating is needed under low input voltage. FROM SOURCE TO SITE ® W - www.orlight.com T - 01923 851 890 E - [email protected]
Related documents