Download Vendor Configuration Guide

T e c h C o n n e c t
A p p N o t e
TC-16029
Date: March 2016
Product: ShoreTel | Orange BTIP/BT
System version: ShoreTel 14.2
Configuration Guide
For Use with Orange BTIP/BT
(Direct Connectivity to Virtual & Physical ShoreTel Appliances)
Version 9
March 29th 2016
Page 1 of 32
ShoreTel tests and validates the interoperability of the Member's solution with ShoreTel's published
software interfaces. ShoreTel does not test, nor vouch for the Member's development and/or quality
assurance process, nor the overall feature functionality of the Member's solution(s). ShoreTel does not
test the Member's solution under load or assess the scalability of the Member's solution. It is the
responsibility of the Member to ensure their solution is current with ShoreTel's published interfaces.
The ShoreTel Technical Support organization will provide Customers with support of ShoreTel's
published software interfaces. This does not imply any support for the Member's solution directly.
Customers or reseller partners will need to work directly with the Member to obtain support for their
solution.
TABLE OF CONTENTS
1
Introduction ............................................................................................................................. 3
1.1
1.2
1.3
1.4
1.5
1.6
2
3
Description of the Orange Service .............................................................................. 3
Pre ShoreTel IP PBX Configuration Activity ................................................................ 3
Customer Questions ................................................................................................... 4
Trouble Reporting ....................................................................................................... 4
Document Feedback................................................................................................... 4
Document Change History .......................................................................................... 5
Version Information ................................................................................................................ 5
Special Notes .......................................................................................................................... 6
3.1
Emergency 911/E911 Services Limitations and Restrictions....................................... 6
3.2
Fax Support ................................................................................................................ 7
3.3
Test Environment ....................................................................................................... 7
3.4
ShoreTel IP Handset Support ..................................................................................... 8
3.5
Unsupported Features and Limitations ....................................................................... 9
3.5.1
ShoreTel SIP Unsupported Features .................................................................. 9
3.5.2
Features Out of Scope for this Interop ...............................................................10
3.5.3
Unsupported Features .......................................................................................10
3.5.4
Feature Warnings ..............................................................................................11
4
5
Configuration Component Overview .................................................................................... 12
Configuration Guide ............................................................................................................. 14
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
5.10
5.11
5.12
5.13
5.14
5.15
6
7
8
ShoreTel Configuration ..............................................................................................14
Login to ShoreTel Director .........................................................................................14
ShoreTel System Settings – General .........................................................................14
Call Control Settings ..................................................................................................14
Codec Lists................................................................................................................17
Sites Settings ............................................................................................................18
Sites Edit screen – Admission Control Bandwidth ......................................................19
Sites Edit screen – Intra / Inter-Site Calls...................................................................19
Switch Settings - Allocating Ports for SIP Trunks .......................................................19
ShoreTel System Settings – SIP Trunk Profile ...........................................................20
ShoreTel System Settings – Trunk Groups ................................................................22
Custom Dial Plan Configuration .................................................................................26
ShoreTel System Settings – Individual Trunks ...........................................................27
ShoreTel System Settings – Trusted IP Ranges ........................................................29
ShoreTel Technical Support ......................................................................................31
Document and Software Copyrights ..................................................................................... 31
Trademarks ........................................................................................................................... 31
Disclaimer ............................................................................................................................. 32
Page 2 of 32
1 Introduction
1.1
Description of the Orange Service
Orange Business Services is a global telecommunications operator and IT services company.
Our 20,000 employees support companies, local government bodies and public sector
organizations in every aspect of their digital transformation.
Business Talk is the global fixed voice service offer for Multi-National Companies (MNC)
relying on our state of the art IP network. It allows all sites of an MNC to effectively
communicate with each other (intra-company communications called on-net) and the outside
world (off-net communications) at competitive tariffs regardless of their location and access
technology.
Business Talk is designed for customer sites equipped with either traditional PBX systems or IP
PBX systems; offering direct access (TDM or IP) or indirect (carrier selection) to our network.
Business Talk offering enables calls to the PSTN network, landlines and mobiles, from any
customer site connected to our voice network in 150+ countries and territories, i.e. calls to
local, national and international fixed & mobile destinations. Calls actually supported depend
on local regulations and the service capabilities may differ from one country to another.
Business Talk offers an enhanced telephony service: calls to non-geographical destinations,
access to emergency and other short code services (e.g. directory assistance), DID numbering
resources allocation including number portability are supported.
BTIP (Business Talk IP) is the extension of the BT (Business Talk) offer dedicated to the French
market.
It is worth noting that, in addition to ShoreTel’s Innovation Network validation process,
ShoreTel have also gained certification through the Orange VISIT validation process.
1.2
Pre ShoreTel IP PBX Configuration Activity
This guide assumes that the administrator is knowledgeable in configuring and
administering the ShoreTel IP PBX. An important tool that administrators should have at
their disposal prior to testing their ShoreTel IP PBX with Orange BTIP is a network
protocol analyzer. Such software can be used to run traces on problem calls so the
information can be shared with equipment and network engineers. There is a free
version of such software that can be obtained at http://www.wireshark.org/. A second
alternative that customers may use is TCPDUMP which can be found on most UNIX
and Linux systems. To use this software the customer should have Wireshark or
TCPDUMP loaded on a server that is connected to a LAN switch or hub that can
monitor both the signaling and media packets on any calls between the customer PBX
and the BTIP service. Please note, however, that ShoreTel and Orange do not offer,
warrant, or support this software, and any use of the Wireshark or TCPDUMP software
is entirely at the customer’s own risk.
Page 3 of 32
1.3
Customer Questions
Section 5 of this guide provides screen shots and instructions for the configuration of
the ShoreTel IP PBX. Should you have questions regarding these instructions, please
call ShoreTel at 1-800-742-2348. When calling this number please have the following
information available:

Company Name

Company Location

Administrator Name & phone number

ShoreTel release and build number

Customer Configuration Guide - Issue number & date
1.4
1.5
Trouble Reporting

In the event that you experience problems with the ShoreTel system you may
contact ShoreTel Technical Assistance Centre at +1 (800) 742-2348 (Toll Free)
or +1 (408) 331-3313 (International). A support contract must be in place before
any assistance will be provided, for contract / account questions please send an
email to [email protected].

In case of an interoperability issue where the suspected source is the BTIP/BT
infrastructure, the client (or system integrator) may request assistance from the
Orange hot line number that will have been provided as part of the service
provisioning following acceptance tests that validate the connection of the
customer sites to BTIP/BT.

ShoreTel and Orange will make every effort to quickly resolve reported troubles.
The time required for trouble shooting can be reduced if the customer has the
necessary detailed information available when reporting a problem. Prior to
reporting a problem please provide a wireshark or TCPDUMP trace of the failed
call.
Document Feedback
ShoreTel IP PBX administrators who would like to provide feedback on the contents of
this document should send it to [email protected].
Page 4 of 32
1.6
Document Change History
Version 1 Issue 1
25/11/2015; Initial draft submitted for review
Version 2 Issue 1
24/12/2015; Minor changes following peer review
Version 3 Issue 1
11/01/2016; Emergency Services statement and minor changes
Version 4 Issue 1
28/01/2016; Minor changes following peer review
Version 5 Issue 1
04/02/2016; Minor changes following peer review
Version 6 Issue 1
26/02/2016; Changes to codec support and custom dial plan entries
Version 7 Issue 1
01/03/2016; Added section 1.4 support information for Orange
Version 8 Issue 1
04/03/2016; Added note informing of GA18 containing the CaC fix
Version 9 Issue 1
IP ranges
29/03/2016; Renumbered incorrect diagrams, added section for Trusted
2 Version Information
Orange
ShoreTel
Release
Business Talk IP (BTIP)
Business Talk (BT)
14.2
Build
19.46.1802.0

Following are screen shots of the versions of ShoreTel utilized for testing interoperability
with Orange BTIP/BT.
Page 5 of 32
Figure 1 – ShoreTel Director Login Page
3 Special Notes
3.1
Emergency 911/E911 Services Limitations and Restrictions
Static Emergency Services. BTIP/BT Local Voice Services support access to local
emergency services or local public safety access point (PSAP) from any Customer
Location that is connected to the Orange Voice Network (“Static Emergency Services”).
To enable the local emergency services dispatch centre or the PSAP to locate the origin
of the calls properly and to enable Orange to route the call to the nearest emergency
services dispatch center or local PSAP, the Customer shall ensure that the CLID/ANI
presented to the Orange Voice Network corresponds to the actual physical address
from which the call originates. By using the Business Talk Local Voice Services, the
Customer warrants that the Customer Location address and associated CLID/ANIs are
complete and accurate. The Customer acknowledges and agrees that the Static
Emergency Services may not function correctly or at all, and that Orange will not be
responsible or liable therefor, in the event of: User’s failure to enter accurate calling
location data, an Orange Network outage, Orange Network congestion, Customer's
network failure, misconfiguration of Customer’s network, equipment malfunctions, power
outages, an emergency or PSAP failure, Force Majeure Event, etc. The Customer
acknowledges that the Customer and its Users are responsible to inform their end users
and guests on their premises of the limitations and requirements of this type of service.
Page 6 of 32
Nomadic Emergency Services. In those countries where permitted by local regulation
and offered by Orange, the Business Talk Local Voice Services support access to local
emergency services or PSAP from any Location subscribed to the Service (e.g., fixed
public Internet access point, fixed personal Internet access point, etc.) (“Nomadic
Emergency Services”). To enable the emergency services dispatch centre or the PSAP
to locate the origin of the calls properly and to enable Orange to route the call to the
nearest emergency services dispatch center or local PSAP, the Customer shall ensure
that the CLID/ANI presented to the Orange Voice Network corresponds to the actual
physical address from which the call originates. By using the Business Talk Local
Services, the Customer warrants that the Location address and associated CLID/ANI’s
are complete and accurate. The Customer expressly acknowledges and agrees that it is
solely the Customer's obligation and responsibility to ensure that each User enters and
timely updates the correct, accurate and current calling location data into the End Point
for each calling location as specifically as possible (e.g., floor number, suite number,
seat or desk information, etc.). The Customer acknowledges and agrees that the
Nomadic Emergency Services may not function correctly or at all, and that Orange will
not be responsible or liable therefor, in the event of: User’s failure to enter accurate
calling location data, an Orange Network outage, Orange Network congestion,
Customer's network failure, misconfiguration of Customer’s network, equipment
malfunctions, power outages, an emergency or a local PSAP failure, Force Majeure
Event, etc. The Customer acknowledges that the Customer and its Users are
responsible to inform their end users and guests on their premises of the limitations and
requirements of this type of service.
3.2
Fax Support
The support of fax transmissions over the BTIP/BT service is out of scope for this
version of the application note.
3.3
Test Environment
The environment that was used to complete this interoperability testing with Orange BTIP/BT
services is shown below.
Page 7 of 32
In total, two different test environments were used – an Enterprise system with a remote
site; and a separate single site SBE system. The Enterprise system consisted of a
number of virtual appliances including a virtual trunk appliance to provide connectivity to
the BTIP/BT service. Additionally, the remote site has connectivity to the PSTN via a
traditional ISDN BRI connection. The SBE platform used an SG90BRI switch for
connectivity to the BTIP/BT service.
3.4
ShoreTel IP Handset Support
The testing for the Orange BTIP/BT service was carried out using IP400 series
handsets along with the IP930D DECT handsets. Testing for the remaining MGCP
handsets is out of scope for this version of the application note.
Page 8 of 32
3.5
Unsupported Features and Limitations
3.5.1
ShoreTel SIP Unsupported Features
Please refer to the ShoreTel Administration Guide, Chapter 18 – Session Initiation
Protocol, for supported and unsupported features via SIP Trunks. Following are some
feature limitations via SIP Trunks:

Fax redirect not supported via SIP Trunks using G.711 (though Direct Inward
Dialing (DID) to fax endpoint is supported)

ShoreTel supports Music On Hold (MOH) over SIP trunks. The maximum number
of music on hold (MOH) streams that a SIP-enabled hardware switch can support
varies with the switch model. The range of such streams across all the voice
switch models is 14–60. Limitation: MOH source needs be on SIP trunk switch.

If the ShoreTel server has a conference bridge 4.2 installed, you should not
enable SIP. The conference bridge is not compatible with a ShoreTel system that
has SIP enabled due to the dynamic RTP port required for SIP.

ShoreTel supports the Service Appliance (SA-100) conferencing / IM system
from Release -12. SIP trunk calls from / to the SA-100 is supported. The SA-100
accepts access codes in DTMF RFC2833 only.

4 to 6 party conferences, when a SIP trunk is involved, utilize Make Me
conference ports.

Silent Monitoring, Barge-In, Silent Coach, Park/Unpark , Call recording features
are supported on a SIP trunk call only if SIP trunk is configured with SIP profile
supporting media hairpinning and the trunk is on a half-width switch.

Silence detection on trunk-to-trunk transfers is not supported, it requires a
physical trunk.

The ShoreTel system does not initiate calls with a 30ms payload; all calls are
initiated with a 20ms payload.

External Party might not hear Music on Hold when Bridge Call Appearance User
places call on hold, due to ShoreTel Defect 1-708568181. Please note that this
issue is only identified on this specific scenario.
Page 9 of 32
At this time we are unable to provide additional information on a resolution to the issues
mentioned above, but suggest to periodically refer to the ShoreTel 14.2 Software
Release Notice (Build Notes) for updates, which can be found at the following location:
http://support.shoretel.com
There may be other feature limitations when using SIP Trunks. Please refer to Chapter
18 of the ShoreTel Administration Guide.
3.5.2
Features Out of Scope for this Interop
A number of features are considered out of scope for this version. This doesn’t mean
they won’t work, but they have not been included in any test plans and their use is not
supported. Features that are not included are as follows.

ShoreTel Enterprise Contact Centre

Bridged Call Appearances

Fax, both T.38 and Pass-through
3.5.3
Unsupported Features
During testing a number of features were found to be problematic for various reasons,
and are therefore considered unsupported at this time. These are listed below.

Simultaneous Ringing with External Numbers (where accept call on answer is
enabled) – Due to a software defect on the ShoreTel platform Simultaneous
Ringing calls that involve an external telephone number as the simultaneous
destination fail. This is due to the ShoreTel Hardware appliances re-inviting with
the G711u codec which is not supported by Orange. In this case Orange tear
down the call and the call does not complete.

G.729 – Use of the G.729 codec has been found to cause various issues
therefore it is deemed to be unsupported when used with Orange BTIP/BT SIP
Trunks.
Page 10 of 32
3.5.4
Feature Warnings
During testing two problems were discovered which must be taken into consideration.
These are detailed in this section.
When using External Assignment with an external number where the user selects to
press 1 to accept the call. In this case, the External Assignment destination receives the
call but the greeting played to the user by the ShoreTel system is very difficult to
understand, although the call does complete. The advice here is that the feature can be
used but you must select the option to accept the call on answer not the option to press
1 to accept.
A software defect was found that effects the ability to report on bandwidth utilization
within the Diagnostics and Monitoring dashboard and the ShoreTel Director reports. The
Virtual Service Appliance will always report bandwidth utilization of 0, and this value
overrides all other bandwidth reporting causing all reports to show 0 bandwidth
utilization across all sites. The fix for this issue was included in 14.2 GA18.
Page 11 of 32
4 Configuration Component Overview
This section provides a more detailed description of the ShoreTel requirements and
configuration.
The ShoreTel and Orange BTIP environment is shown next.
Figure 2 – Configuration Component Overview
The ShoreTel customer premises site shall consist of the following components:

ShoreTel IP Phones – The ShoreTel IP Phones tested in this application note
are IP400 series handsets that use SIP for call signaling with the ShoreTel
appliances. IP930D DECT handsets were also included in the testing.

ShoreTel IPBX – The ShoreTel Appliances provide connectivity for IP handsets
and SIP trunks. Both the IP handsets and all trunk resources communicate using
SIP as their call control mechanism with the exception of the IP930D handset
which uses MGCP. The ShoreTel PBX implements PBX functionality including
phone features, calling routing, voice mail, etc.

ShoreTel Communicator – This is ShoreTel Unified Communications client
application that is available to all users of the ShoreTel system.

Customer Edge – This is the customer premises equipment that is supplied and
managed by Orange.
As shown in the diagram above, SIP signaling is used between the IP phones and the
ShoreTel appliances. The trunk resources within the appliances use SIP to
communicate with the BTIP service. The RTP voice traffic flows from the IP phones to
Page 12 of 32
the BTIP platform via the trunk appliance (where media proxy resources are in use) or
from the handset direcly to the BTIP platform where media proxy resources are not
being used.
The Orange BTIP service is provided over a dedicated MPLS service over which is a
BVPN service with a private IP address range assigned by Orange. The a-sbc in the
network is where ShoreTel will direct all outbound SIP calls. Orange will provide the IP
address required for the SIP trunk configuration on the ShoreTel system.
The configuration information below shows examples for configuring the ShoreTel
platform. Even though configuration requirements can vary from setup to setup, the
information provided in these steps, along with ShoreTel Planning and Installation
Guide should prove to be sufficient. However, every design can vary and some may
require more planning than others.
Configuration guidelines as documented by Orange during Visit program certification
campaign can be found on OBS Web portal.
Page 13 of 32
5 Configuration Guide
5.1
ShoreTel Configuration
This section describes the ShoreTel system configuration to support SIP Trunking. The
section is divided into general system settings and trunk configurations (both group and
individual) needed to support SIP Trunking.
5.2
Login to ShoreTel Director
First you must login to ShoreTel Director in the usual manner (Figure 3).
Figure 3 – ShoreTel Director Login
5.3
ShoreTel System Settings – General
The first settings to address within the ShoreTel system are the general system
settings. These configurations include the Call Control, the site and the Switch Settings.
If these items have already been configured on the system, skip this section and go on
to the “ShoreTel System Settings – Trunk Groups” section below.
5.4
Call Control Settings
The first settings to configure within ShoreTel Director are the Call Control Options. To
configure these settings for the ShoreTel system, login to ShoreTel Director and select
“Administration” then “Call Control” followed by “Options” (Figure 4).
Page 14 of 32
Figure 4 –Administration Call Control Options
The “Call Control Options” screen will then appear (Figure 5).
Page 15 of 32
Figure 5 - Call Control Options
In the “General” parameters, the “DTMF Payload Type (96 – 127)” defaults to a value
of “102”. This must be changed to 101.
Within the “SIP” parameters; confirm that the appropriate settings are made for the
“Realm” “Enable SIP Session Timer”.
The “Realm” parameter is used in authenticating all SIP devices. It is typically a
description of the computer or system being accessed. Changing this value will require
a reboot of all ShoreGear switches serving SIP extensions. It is not necessary to modify
Page 16 of 32
this parameter to get the ShoreTel IP PBX system functional with Orange BTIP. Verify
that the “Enable SIP Session Timer” box is checked (enabled). Next the Session
Interval Timer needs to be set. The recommended setting for “Session Interval” is “90”
seconds. The last item to select is the appropriate refresher (from the pull down menu)
for the SIP Session Timer. The “Refresher” field will be set either to “Caller (UAC)”.
The next settings to verify are the “Voice Encoding and Quality of Service”,
specifically the “Media Encryption” parameter, make sure this parameter is set to
“None”, otherwise you may experience one-way audio issues. Please refer to
ShoreTel’s Administration Guide for additional details on media encryption and the other
parameters in the “Voice Encoding and Quality of Service” area.
5.5
Codec Lists
By default, ShoreTel 14.x has 13 built-in codecs; these codecs can be grouped into
Codec Lists and defined in the sites page for Inter-site and Intra-site calls. When
establishing a call with Orange BTIP the preferred codec choice is G.711a (PCMA) so
you must either modify an existing Codec List or create a new one, making sure that
PCMA is included. Codec Lists are modified by selecting “Administration”, then “Call
Control” followed by “Codec Lists” from ShoreTel Director (Figure 6).
Figure 6 – Administration Call Control Codec Lists
The following example shows a sample codec list which contains G.711a (Figure 7).
Please note that the G.722 codec is not supported for use with the virtualized SIP trunk
Page 17 of 32
switch. When creating the codec list ensure that G.711u is placed at the bottom of the
list as this codec is not supported by the BTIP/BT service.
Figure 7 – Modifying a Codec List
5.6
Sites Settings
The next settings to address are the administration of sites. These settings are modified
under the ShoreTel Director by selecting “Administration” then “Sites” (Figure 8).
Figure 8 – Administration Sites
This selection brings up the “Sites” screen. Within the “Sites” screen select the name of
the site to configure. The “Edit Site” screen will then appear. The only changes
Page 18 of 32
required to the “Edit Site” screen are to the “Admission Control Bandwidth” and “IntraSite / Inter-Site Calls” parameters (Figure 9).
Figure 9 – Site Bandwidth settings
Note: Bandwidth of 1024 is just an example. Please refer to the ShoreTel Planning and
Installation Guide for additional information on setting Admission Control Bandwidth. Be
sure to use the codec list created in the previous section for the Intra-Site Codec list.
5.7
Sites Edit screen – Admission Control Bandwidth
The Admission Control Bandwidth defines the bandwidth available to and from the site.
This is important as SIP trunk calls may be counted against the site bandwidth.
Bandwidth needs to be set appropriately based on site setup and configuration with the
Orange BTIP service. Please refer to the ShoreTel Planning and Installation Guide for
additional information.
5.8
Sites Edit screen – Intra / Inter-Site Calls
Configure the Inter-Site Calls option to a “Codec List” that contains the desired codecs
and save the change. The site that the SIP Trunk Group belongs to will determine which
Inter-Site Codec List will be utilized. Be sure to set the codec list you added / modified
earlier in this section to include the PCMA codec. Please refer to the ShoreTel Planning
and Installation Guide for additional information.
5.9
Switch Settings - Allocating Ports for SIP Trunks
The final general settings to configure are the ShoreTel appliance settings. These
changes are modified by navigating to Administration, Platform Hardware, Voice
Switches / Service Appliances, Primary in ShoreTel Director. The configuration of
ShoreTel appliance resources for SIP trunks is out of scope of this document as it is
assumed that the reader is familiar with this process.
Starting with ShoreTel 13, the additional Port Type of ‘SIP Trunk with Media Proxy’ was
added for half-width ShoreTel switches. It ensures that the ShoreTel system that is
being used for SIP Trunks will provide feature parity similar to PRI trunks. These feature
Page 19 of 32
include RFC 2833 DTMF detection for Office Anywhere, External or Simultaneous Ring
calls, three party Mesh Conferencing (without needing to configure “MakeMe”
conference ports), Call Recording, Silent Monitoring, Barge-In, Whisper Page, Invites
with no SDP and when there’s no common codec between ITSP and the local
extension. By default, ShoreTel Virtual Trunk Switches include “SIP Media Proxy”
resources therefore no configuration is required.
For further information on “SIP Trunk with Media Proxy” please refer to the ShoreTel
System Administration Guide.
5.10 ShoreTel System Settings – SIP Trunk Profile
It is necessary to configure specific SIP options for the BTIP service. This is done
through a SIP profile configured by selecting “Administration” then “Trunks” followed by
“SIP Profile” (Figure 10).
Page 20 of 32
Figure 10 – SIP Trunk Profile list
Modify the ‘Default ITSP’ profile and create a copy by clicking on the ‘Copy’ button, then
complete the form as follows (Figure 11).
Figure 11 – SIP Trunk Profile list
Figure 12 – SIP Trunk Profile configuration
Name: Orange Profile
Enable: Yes (check the box)
Custom Parameters:
Page 21 of 32

1CodecAnswer=1
5.11 ShoreTel System Settings – Trunk Groups
The settings for Trunk Groups are changed by selecting “Administration”, then “Trunks”
followed by “Trunk Groups” within ShoreTel Director (Figure 13).
Figure 13 – Administration Trunk Groups
This selection brings up the “Trunk Groups” screen (Figure 14).
Figure 14 – Trunk Groups Settings
From the pull down menus on the Trunk Groups screen select the desired site and then
choose ‘SIP’ as the trunk type to configure. Then click on the ‘Go’ link. The “Edit SIP
Trunk Group” screen will appear (Figure 15).
Page 22 of 32
Figure 15 – SIP Trunk Group Settings
The “Enable SIP Info for G.711 DTMF Signaling” parameter should not be enabled
(checked). Enabling SIP info is currently only used with SIP tie trunks between
ShoreTel systems.
The “Profile:” parameter should be configured to use the ‘Orange’ SIP Profile created in
a previous step.
The “Enable Digest Authentication” parameter defaults to “<None>” and no
modification is required when connecting to the BTIP service.
The next item to change in the “Edit SIP Trunks Group” screen is to make the
appropriate settings for the “Inbound:” parameters. (Figure 16).
Figure 16 – Inbound Trunk Group Settings
Within the “Inbound:” settings, ensure the “Number of Digits from CO:” is configured
to a value of “12”, this is the number of digits that the ShoreTel SIP trunk switch will be
Page 23 of 32
receiving from the BTIP service. Enable (check) the “DNIS” or “DID” parameters as
needed. It is no longer needed to enable the “Extension” and Tandem Trunking
parameter. For additional information on these parameters please refer to the ShoreTel
Administration Guide.
Page 24 of 32
The following section is configured in the same way as any normal Trunk Group (Figure
17).
Figure 17 – Outbound and Trunk Services
Enable (check) the “Outbound” parameter and define a Trunk “Access Code” and “Local
Area Code” as appropriate. In the “Billing Telephone Number:” be sure to specify the
main telephone number provided by Orange for your account.
In the “Trunk Services:” area, make sure the appropriate services are enabled or
disabled based on what Orange supports and what features are needed from this Trunk
Group. You will need to enable (check) the “Enable Original Caller Information”
parameter. This allows the ShoreTel system to include the called telephone number as
part of a SIP Diversion header for forwarded calls.
Page 25 of 32
The parameter “Caller ID not blocked by default” determines if the call is sent out as
<unknown> or with caller information (Caller ID), be sure to enable (check) this
parameter. User DID will impact how information is passed out to the SIP Trunk group.
5.12 Custom Dial Plan Configuration
As part of the configuration for the Orange BTIP service you are required to make
changes to the custom dial plan section of the trunk group, an activity that requires a
special logon into ShoreTel Director. There are two elements to the custom dial plan.
The first enables the ‘Make Number Private’ feature to work correctly. The second
prioritizes the primary and secondary trunk groups for setups where Orange have
provided a secondary trunk for the purposes of redundancy. A custom dial string must
be entered into both the primary and secondary trunk group.
Go to the ShoreTel Director login page (simply log out if you’re currently logged in), and
on your keyboard, hold down the <CTRL> and <Shift> keys and with the mouse pointer
and then click pointer on the “U” of the “Username:” field. This will enable the “Support
Entry” mode of the ShoreTel Director, as referenced below in (Figure 18).
Figure 18 – ShoreTel Director Support Entry
Login to ShoreTel Director with your normal administration user credentials. Select
“Administration”, then “Trunks” followed by “Trunk Groups” and modify the SIP trunk
group that you’ve created for the Primary trunks.
Enter the custom dial plan by clicking on the “Edit” button at the bottom of the page. A
small dialog box will appear to allow you to specify the custom dial plan entry (Figure
19). This custom dial plan entry is to facilitate the blocking of outbound CLID by the user
should they wish to do so.
For the PRIMARY trunk group copy and paste the following string into the dialog box
that appears and then click on the “Save” button (Figure 19).
Page 26 of 32
;-28A;65E
Figure 19 – Custom Dial Plan Entry
Next, edit the SECONDARY trunk group’s custom dial plan by clicking on the “Edit”
button at the bottom of the page. You must repeat the process and use the following
custom dial string and then click on the “Save” button.
;-10A;65E
5.13 ShoreTel System Settings – Individual Trunks
ShoreTel Trunk Groups only support Static IP Addresses for Individual Trunks and
Orange will provide the IP address where your SIP trunks should be pointed. This
section covers the configuration of the individual trunks. Select “Administration”, then
“Trunks” followed by “Individual Trunks” to configure the individual trunks (Figure 20).
Page 27 of 32
Figure 20 – Individual Trunks
The “Trunks by Group” screen is used to change the individual trunks settings that
appear (Figure 20).
Figure 21 – Trunks by Group
Select the site for the new trunk(s) to be added and select the appropriate trunk group
from the pull down menu in the “Add new trunk at site” area. In this example, the site is
“Headquarters” and the trunk group is “Primary SIP Trunks”, as created above, see
Figure 21. Click on the “Go” button to bring up the “Edit Trunk” screen (Figure 22).
Page 28 of 32
Figure 22 - Edit Trunks Screen for Individual Trunks
From the individual trunks “Edit Trunk” screen, input a name for the individual trunks,
select the appropriate switch, select the SIP Trunk type and input the number of trunks.
When selecting a name, the recommendation is to name the individual trunks the same
as the name of the trunk group so that the trunk type can easily be tracked. Select the
switch upon which the individual trunk will be created. For the “IP Address” you must
specify the IP address supplied to you by Orange. The last step is to select the number
of individual trunks desired (each one supports “one” audio path – example if 10 is
configured, then 10 audio paths can be established at one time). Once these changes
are complete, select the “Save” button to commit changes.
After setting up the trunk groups and individual trunks, refer to the ShoreTel Planning
and Installation Guide to make the appropriate changes for the User Group settings.
This completes the settings for the ShoreTel system.
5.14 ShoreTel System Settings – Trusted IP Ranges
In this configuration the ShoreTel system is connecting directly to the Orange network,
therefore it may be necessary to define Orange IP address ranges as trusted so the
ShoreTel system does not discard packets received from these addresses. For
example, if RTP traffic is being received from IP addresses that are not defined as
trusted then the ShoreTel system will drop these packets.
Select “Administration”, then “System Parameters” followed by “Trusted IP Ranges” to
configure the individual trunks (Figure 23).
Page 29 of 32
Figure 23 – Trusted IP Ranges
From here you can see the currently defined IP address ranges that are trusted. Click
on the ‘New’ button to create a new range (Figure 24).
Figure 24 – Create new trusted IP range
Give the range a name (‘Orange’, for example), then specify the lower and upper
address of the range as defined by Orange (Figure 25). These will be the addresses
from which you will receive SIP and RTP traffic from Orange. Click on the “Save” button
to commit the changes.
Page 30 of 32
Figure 25 – Define the trusted IP range
5.15 ShoreTel Technical Support
In the event that you have problems with the ShoreTel system you may contact
ShoreTel Technical Assistance Center at +1 (800) 742-2348 (Toll Free) or +1 (408)
331-3313 (International). A support contract must be in place before any assistance will
be provided, for contract / account questions please send an email to
[email protected].
6 Document and Software Copyrights
Copyright © 2013 by ShoreTel, Inc., Sunnyvale, California, U.S.A. All rights reserved.
Printed in the United States of America. Contents of this publication may not be
reproduced or transmitted in any form or by any means, electronic or mechanical, for
any purpose, without prior written authorization of ShoreTel Communications, Inc.
ShoreTel, Inc. reserves the right to make changes without notice to the specifications
and materials contained herein and shall not be responsible for any damage (including
consequential) caused by reliance on the materials presented, including, but not limited
to typographical, arithmetic or listing errors.
7 Trademarks
The ShoreTel logo, ShoreTel, ShoreCare, ShoreGear, ShoreWare and ControlPoint are
registered trademarks of ShoreTel, Inc. in the United States and/or other countries.
ShorePhone is a trademark of ShoreTel, Inc. in the United States and/or other
countries. All other copyrights and trademarks herein are the property of their
respective owners.
Page 31 of 32
8 Disclaimer
ShoreTel tests and validates the interoperability of the Member's solution with
ShoreTel's published software interfaces. ShoreTel does not test, nor vouch for the
Member's development and/or quality assurance process, nor the overall feature
functionality of the Member's solution(s). ShoreTel does not test the Member's solution
under load or assess the scalability of the Member's solution. It is the responsibility of
the Member to ensure their solution is current with ShoreTel's published interfaces.
The ShoreTel Technical Support organization will provide Customers with support of
ShoreTel's published software interfaces. This does not imply any support for the
Member's solution directly. Customers or reseller partners will need to work directly with
the Member to obtain support for their solution.
This Customer Configuration Guide ("CCG") is offered as a convenience to Orange's
customers. The specifications and information regarding the product in this CCG are
subject to change without notice. All statements, information, and recommendations in
this CCG are believed to be accurate but are presented without warranty of any kind,
express or implied, and are provided “AS IS”. Users must take full responsibility for the
application of the specifications and information in this CCG.
In no event shall Orange or its suppliers be liable for any indirect, special,
consequential, or incidental damages, including, without limitation, lost profits or loss or
damage arising out of the use or inability to use this CCG, even if Orange or its
suppliers have been advised of the possibility of such damage.
ShoreTel, Inc.
960 Stewart Drive
Sunnyvale, California 94085 USA
+1.408.331.3300
+1.408.331.3333 fax
Page 32 of 32