Download topic 1 - Department of Electronic Engineering

Document related concepts
no text concepts found
Transcript
EE 2301
BASIC ELECTRONIC CIRCUIT
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
INSTRUCTOR: DR. ANGUS WU
OFFICE:
G6352
PHONE:
9391
EMAIL:
[email protected]
URL: www.ee.cityu.edu.hk/~ee2301
ID:
ee2301
passwd: ee2301
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
LECTURE 1
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Fundamentals
• Charge, Current, Voltage
• Ohm’s Law and Power
• Series Circuits and Kirchhoff’s
Voltage Law
• Parallel Circuits and Kirchholf’s
Current Law
• Resistive Circuits
• Circuit Analysis Techniques
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Charge
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
The Starting Point: Elements,
Atoms and Charge
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Charge
• Charge
– Force that causes two particles to be attracted
to, or repelled from, each other
– Two types – positive and negative
– Atom – proton (positive), electron (negative),
neutron (electrically neutral)
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
• Attraction and Repulsion - Like charges repel
each other and opposite charges attract each other
• Ions
– Outside force can cause an electron to leave its
orbit -atom is referred to as a positive ion
– Outside force can cause an atom to gain an
electron -atom is referred to as a negative ion
• Free Electrons
– An electron that is not bound to any particular
atom
– Can neutralize a positive ion
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Current
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Current
• Current – the directed flow of charge
through a conductor
– Thermal energy (heat) is sufficient to free
electrons in copper
– Free electron motion is random unless outside
force is applied
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Current
• Represented by the letter i (for intensity)
• Measured in charge per unit time
where
i = the intensity of the current
dq = the amount of charge
dt = the time (in seconds) required for the
charge (dq) to pass
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Current
• Coulomb (C) – represents the total charge of
approximately 6.25 x 1018 electrons
• Unit of Current – Ampere (A) = 1
coulomb/second
• Example: 3 coulombs of charge pass a point in a
wire every two seconds. Calculate current.
Q 3C
I 
 1.5 C/s  1.5 A
t
2s
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Electrical Current
Electrical current is the time rate of flow of
electrical charge through a conductor or
circuit element. The units are amperes (A),
which are equivalent to coulombs per
second (C/s).
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Electrical Current
dq(t )
i (t ) 
dt
t
q(t )   i (t )dt  q(t0 )
t0
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Electrical Current
• Electron Flow Versus Conventional Current
Insert Figure 1.10
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Direct Current
Alternating Current
When a current is constant with time, we
say that we have direct current,
abbreviated as dc. On the other hand, a
current that varies with time, reversing
direction periodically, is called alternating
current, abbreviated as ac.
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Figure 4.17,
4.18
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
.
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Two different methods of labeling the same current.
(a,b) Incomplete, improper, and incorrect definitions of a current.
(c) the correct definition of i1(t).
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Current
Insert Figure 1.11
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Voltage
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Voltage
The voltage associated with a circuit element
is the energy transferred per unit of charge
that flows through the element. The units of
voltage are volts (V), which are equivalent
to joules per coulomb (J/C).
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Voltage
• Voltage – a “difference of potential” that
generates the directed flow of charge
(current) through a circuit
Insert Figure 1.12
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Voltage
• Often referred to as electromotive force
(emf)
• Unit of Voltage – volt (V) = 1
joule/coulomb
• Volt – the difference of potential that uses
one joule of energy to move one coulomb of
charge.
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
(a, b) These are inadequate definitions of a
voltage. (c) A correct definition includes
both a symbol for the variable and a plusminus symbol pair.
BASIC ELECTRONIC ENGINEERING
(a, b) Terminal B is 5 V positive with
respect to terminal A; (c,d)
terminal A is 5 V positive with
respect to terminal B.
Department of Electronic Engineering
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Ideal voltage sources
Various representations of an electrical system
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Symbol for ideal current source
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Ohm’s Law and Power
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Ohm’s Law
• German Physicist – George Simon Ohm
– Found that current is inversely proportional to
resistance for a given voltage
– Known as Ohm’s law
• The Relationship Between Current and Voltage
• The Relationship Between Current and Resistance
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Basic Circuit Calculations
• Using Ohm’s Law to Calculate Current
V
I
R
where
R = the circuit resistance
V = the applied voltage
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Basic Circuit Calculations
• Using Ohm’s Law to Calculate Voltage
V  IR
where
I = the circuit current
R = the circuit resistance
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Basic Circuit Calculations
• Using Ohm’s Law to Calculate Resistance
V
R
I
where
V = the circuit voltage
I = the circuit current
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Resistance Element
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Power
• Power – the amount of energy used per unit
time
• Unit of Power – Watt (W) = 1 joule/second
• Calculating Power
P = IV
where
P = the power used, in watts (W)
V = the applied voltage, in volts (V)
I = the generated current, in amperes (A)
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Power
• Other Power Equations
– Use IR in place of V
P  VI  IR  I  I R
2
– Use V/R in place of I
2
V V
P  VI  V  
R
R
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
If the current arrow is directed into the “ +” marked terminal of an
element, then p = vi yields the absorbed power. A negative value
indicates that power is actually being generated by the element.
If the current arrow is directed out of the “ +” terminal of an element, then
p = vi yields the supplied power. A negative value in this case indicates
that power is actually being absorbed instead of generated.
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Passive Sign Conversion
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
POWER AND ENERGY
p(t )  v(t )i (t )
t2
w   p(t )dt
t1
W  Pt
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
instantaneous power
Power
• Power and Heat
– Resistors and other components convert energy
to heat (transducer)
– If power rating is exceeded, the component will
keep getting hotter and be destroyed
– Common guideline – select a component with
twice the required power-dissipation capability
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Power
• Efficiency – the ratio of a circuit or
components output power to its input power
Po
   100
Pi
where
 = the efficiency, as a percentage
Po = the output power
Pi = the input power
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Miscellaneous Topics
• Resistor Tolerance
– Resistor value falls within a range
– Circuit current also falls within a range
I min
V

Rmax
BASIC ELECTRONIC ENGINEERING
I max
Department of Electronic Engineering
V

Rmin
Miscellaneous Topics
• Circuit Loads
– Source – supplies the power
– Load – absorbs (uses) the power
– Full Load – one that draws the maximum
current
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Practical Voltage Source
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Practical Current Source
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Circuit Topology Fundamental
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Definition of a branch
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Definitions of node and supernode
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
(a) A circuit containing three nodes
and five branches.
(b) Node 1 is redrawn to look like two
nodes; it is still one node.
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Definition of a loop
Definition of a mesh
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Series Circuits
and
Kirchhoff’s Voltage Law
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Voltage Relationships: Kirchhoff’s Voltage Law
• Kirchhoff’s Voltage Law
– The sum of the component voltages in a series
circuit must equal the source voltage
VS  V1  V2 ...  Vn
1840 – German Physicist, Gustav Kirchhoff
– Actual wording – The algebraic sum of the
voltages around a closed loop is zero
– The following equation takes polarity into
account
VS  V1  V2  ...  Vn  0 V
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Kirchhoff’s Voltage Law,
• Example:
VS = +10V, V1 = +2V, V2 = +8V
 VS  V1  V2  -10 V  2 V  8 V  0 V
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Series Circuit Characteristics
• Series Circuit – a circuit that contains only
one current path
R1
R2
R3
Vin
R4
R6
BASIC ELECTRONIC ENGINEERING
R5
Department of Electronic Engineering
(a) Series combination of N resistors. (b) Electrically equivalent circuit.
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Series Circuit Characteristics
• Total Series Resistance
RT  R1  R2 ...  Rn
where
RT = the total circuit resistance
Rn = the highest-numbered resistor
in the circuit
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Series Circuit Characteristics
• Current Characteristics – the current at any
point in a series circuit must equal the
current at every other point in the circuit
Insert Figure 4.5
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Series Circuit Characteristics
• Voltage Characteristics
VS  V1  V2 ...  Vn
where
VS = the source (or total) voltage
Vn = the voltage across the highest numbered
resistor in the circuit
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
(a) Series connected voltage sources can be replaced
by a single source.
(b) Parallel current sources can be replaced by a single
source.
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Examples of circuits with multiple sources, some of which are
“illegal” as they violate Kirchhoff’s laws.
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Series Circuit Characteristics
• Power Characteristics
PS  P1  P2 ...  Pn
 VS I T
where
PS = the source (or total) voltage
Pn = the power that is dissipated across the
highest numbered resistor in the circuit
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Series Circuit Characteristics
Insert Figure 4.10
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Voltage References
• Voltage References - Circuits have a point
that serves as the 0 V reference (ground)
Insert Figure 4.12
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Voltage Divider
• The Voltage Divider Relationship
– Voltage Divider – often used to analyze a series
circuit
Vn Rn
Rn

Vn  Vs
Vs RT
RT
R1
Vs
where
Rn = the resistor of interest
Vn = the voltage drop across Rn
(where n is the component number)
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
RT
R2
We may find v2 by applying KVL
and Ohm’s law:
so
An illustration of
voltage division.
Thus,
or
For a string of N series resistors, we
may write:
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
• Source Resistance: A Practical
Consideration
– Ideal Voltage Source – maintains a constant
output voltage regardless of the resistance of its
load
– Real Voltage Source – internal resistance causes
a decrease in load resistance results in a
decrease in the source voltage
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
• Source Resistance: A Practical
Consideration (Continued)
Insert Figure 4.20
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Maximum Power Transfer Theorem
• maximum power transfer from a voltage
source to its load occurs when the load
resistance is equal to the source resistance
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Series-Connected Voltage Sources
• Series-Aiding Voltage Sources – the total
voltage equals the sum of the voltages
• Series-Opposing Voltage Sources – the total
voltage equals the difference of the voltages
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Earth Ground Versus Chassis Ground
Insert Figure 4.28
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Parallel Circuits
and
Kirchholf’s Current Law
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Current Relationships: Kirchhoff’s Current
• Kirchhoff’s Current
Law – the algebraic
Law
sum of the currents entering and leaving a
point must equal zero
– In other words, the total current leaving a point
must equal the total current entering that point
i2
i1
i3
BASIC ELECTRONIC ENGINEERING
n
i
k 1
k
Department of Electronic Engineering
0
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Parallel Circuit Characteristics
• Parallel Circuit – a circuit that provides more
than one current path between any two points
Insert Figure 5.1
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Parallel Circuit Characteristics
• Current Characteristics
IT  I1  I 2 ...  I n
where
In = the current through the highest-numbered
branch in the circuit
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Parallel Circuit Characteristics
• Voltage and Current Values
– Voltage across each component is equal
– Current through each branch is determined by
the source voltage and the resistance of the
branch.
VS
In 
Rn
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Parallel Circuit Characteristics
• Resistance Characteristics – the total circuit
resistance is always lower than any of the
branch resistance values
Insert Figure 5.5
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Parallel Circuit Characteristics
• Power Characteristics
– Total Power – sum of the power dissipation
values for the individual components
– The lower value of the branch resistance, the
higher percentage of the total power it
dissipates (opposite that of series circuits)
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Parallel Circuit Characteristics
Insert Figure 5.6
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Parallel Resistance Relationships
• Conductance (G)
– A measure of the ability of a component or
circuit to conduct
– Total conductance (GT) in a parallel circuit
equals the sum of the branch conductance
values
GT  G1  G2 ...  Gn
where
Gn = the conductance of the highest-numbered
branch in the circuit
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Parallel Resistance Relationships
• Calculating Total Resistance: The Reciprocal
Method
1
1

1
1
1
G1  G2  ...  Gn

 ... 
R1 R2
Rn
Proof – Using KVL and KCL
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Beginning with a simple KCL equation,
or
Thus,
A special case worth remembering is
(a) A circuit with N resistors in
parallel. (b) Equivalent circuit.
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Parallel Resistance Relationships
• Calculating Total Resistance: The ProductOver-Sum Method
R1R2
RT 
R1  R2
BASIC ELECTRONIC ENGINEERING
RT
Department of Electronic Engineering
R2
R1
Current Sources
• a source that is designed to provide an output
current value that remains relatively constant over
a wide range of load resistance values
Insert Figure 5.12
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Current Dividers
• Current Dividers – the source current is
divided among the branches
Insert Figure 5.15
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
The current flowing through R2 is
or
An illustration of
current division.
BASIC ELECTRONIC ENGINEERING
For a parallel combination
of N resistors, the current
through Rk is
Department of Electronic Engineering
Practical Current Sources:
• The Effects of Source Resistance
– Ideal Current Source – constant current and
infinite internal resistance
– Real Current Source – current varies for a
change in load resistance and internal resistance
is not infinite
– Internal resistance is usually much greater than
the load resistance
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Maximum Power Transfer
– For a fixed value of RS , maximum power transfer
occurs when
RL = RS
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Series-Parallel Circuits
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Series-Parallel Circuits
• Connecting Series Circuits in Parallel
Insert Figure 6.3
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Series-Parallel Circuits
• Connecting Parallel Circuits in Series
Insert Figure 6.5
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Analyzing Series-Parallel Circuits
REQ1  R2 || R3
REQ 2  R5 || RL
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
KIRCHHOFF’S VOLTAGE
LAW
Formal Expression
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
KIRCHHOFF’S VOLTAGE
LAW
The algebraic sum of the voltages equals zero
for any closed path (loop) in an electrical
circuit.
In a closed path, each element is encountered
only once.
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Define the voltage for each component
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Loop 1
-Va + Vb + Vc =0
Loop 2
-Vc – Vd + Ve =0
Loop 3
-Ve + Vd – Vb + Va = 0
Va is ‘+’ in loop 3
But ‘-’ in loop 1
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
VOLTAGE SOURCE
AND
CURRENT SOURCE
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Why ?
As I = V/R, R = 0,
implies, I is infinitive
Power = VI = infinitive?
Theoretical correct but not
in real world.
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Symbols for dependent sources
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
KIRCHHOFF’S CURRENT
LAW
Formal Expression
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
KIRCHHOFF’S CURRENT LAW
• The net current entering a node is zero.
n

k 1
ik  0
• Alternatively, the sum of the currents
entering a node equals the sum of the
currents leaving a node.
n

k 1
n
iinputk   ioutputk
k 1
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
(a)
(b)
i a = 1A + 3A = 4A
i b + 1 A + 3 A = 2 A, i b = - 2A, that is flowing outward
(c) i c + 4 A + 1 A + 3 A = 0, i c = - 8 A, flows outward too
BASIC ELECTRONIC ENGINEERING
Department of Electronic Engineering
Related documents