PLUS+1® Controllers MC012-110 and MC012-112
... yy 2 outputs –– (2) universal (PWMOUT/DOUT/PVGOUT) that are user-defined as either: Digital: (3 A), configurable as source or sink; PWM: (30 to 4000 Hz), configurable as open or closed loop with current control; Analog voltage: open loop PWM at 4000 Hz –– Any PWMOUT/DOUT/PVGOUT can be used to provid ...
... yy 2 outputs –– (2) universal (PWMOUT/DOUT/PVGOUT) that are user-defined as either: Digital: (3 A), configurable as source or sink; PWM: (30 to 4000 Hz), configurable as open or closed loop with current control; Analog voltage: open loop PWM at 4000 Hz –– Any PWMOUT/DOUT/PVGOUT can be used to provid ...
Mipco™ Connections for Refrigerated Containers No One Does It
... modular design, mechanically interlocked to allow the circuit to be energized only after a mating plug is fully inserted into the receptacle and the actuating rod is pushed forward. All interlocked receptacles shall allow the de-energizing of the circuit before mated contacts are disengaged upon plu ...
... modular design, mechanically interlocked to allow the circuit to be energized only after a mating plug is fully inserted into the receptacle and the actuating rod is pushed forward. All interlocked receptacles shall allow the de-energizing of the circuit before mated contacts are disengaged upon plu ...
IP-600D,450D,300D CE ›p
... • An internal limiter limits the current during overload, and a protection circuit disconnects the output during an output short circuit by detecting the levels of both voltage and current. The protection circuit also disconnects the output during an abnormal temperature rise. • Large output screw t ...
... • An internal limiter limits the current during overload, and a protection circuit disconnects the output during an output short circuit by detecting the levels of both voltage and current. The protection circuit also disconnects the output during an abnormal temperature rise. • Large output screw t ...
DFW Series Wig-Wag Flasher
... The DFW flasher unit employs a pair of heavy duty automotive relays, each of which are driven by a silicon transistor connected in a switching configuration. The oscillator circuit provides proven solid state reliability while the relays allow control of heavy load currents without the need for a he ...
... The DFW flasher unit employs a pair of heavy duty automotive relays, each of which are driven by a silicon transistor connected in a switching configuration. The oscillator circuit provides proven solid state reliability while the relays allow control of heavy load currents without the need for a he ...
HARDWARE MANUAL 4K242, 4K1042, 4K1142
... DA15 GPIO The GPIO switch/led connector is a DA15 female. This connector is used to allow the player to control external LEDs or other devices requiring 24mA of current or less. Connect the LED outputs to the LED ANODE and connect the LED CATHODE to the ground. If you want to connect another device, ...
... DA15 GPIO The GPIO switch/led connector is a DA15 female. This connector is used to allow the player to control external LEDs or other devices requiring 24mA of current or less. Connect the LED outputs to the LED ANODE and connect the LED CATHODE to the ground. If you want to connect another device, ...
DMPA MANUAL
... The optical output jack of the DMPA can have one of two formats. When this switch is depressed AND lit blue, this jack will output 8 channels of ADAT. (ADAT cannot be output if the sample rate exceeds 48KHZ - the Sample Rate selection being set to an internal rate). In this case the switch cap will ...
... The optical output jack of the DMPA can have one of two formats. When this switch is depressed AND lit blue, this jack will output 8 channels of ADAT. (ADAT cannot be output if the sample rate exceeds 48KHZ - the Sample Rate selection being set to an internal rate). In this case the switch cap will ...
Instruction Manual
... PCB round pin terminals. The marking on the PC board shows this. The signal output can provide balanced or unbalanced signals. See fig. 2 and fig. 3 ...
... PCB round pin terminals. The marking on the PC board shows this. The signal output can provide balanced or unbalanced signals. See fig. 2 and fig. 3 ...
One Home. One App.
... every LightwaveRF device has been carefully designed so that it works manually as well as remotely; a LightwaveRF light switch can be used like any other standard light switch. ...
... every LightwaveRF device has been carefully designed so that it works manually as well as remotely; a LightwaveRF light switch can be used like any other standard light switch. ...
A 400 MHz DDS Core Unit
... As an option, the I/OSync signal (pin 5) can be tied to the Reset signal; the Reset signal can be generated either locally, by placing on the capacitor C23 and the resistor R14 or by the microcontroller subsystem, but in this case C23 must be removed. U2 provides the regulation for the 3,3 Volt Digi ...
... As an option, the I/OSync signal (pin 5) can be tied to the Reset signal; the Reset signal can be generated either locally, by placing on the capacitor C23 and the resistor R14 or by the microcontroller subsystem, but in this case C23 must be removed. U2 provides the regulation for the 3,3 Volt Digi ...
MAX2204EVKIT.pdf
... the EV kit and testing the device’s function. Caution: Do not turn on the DC power or RF signal generators until all connections are made: 1) Set the jumper (JP1) on the EV kit to ON. This enables the device. 2) Connect a DC supply set to +2.85V (through a DMM, if desired) to the VCC and GND termina ...
... the EV kit and testing the device’s function. Caution: Do not turn on the DC power or RF signal generators until all connections are made: 1) Set the jumper (JP1) on the EV kit to ON. This enables the device. 2) Connect a DC supply set to +2.85V (through a DMM, if desired) to the VCC and GND termina ...
usa 1310 specifications
... Each channel of the amplifier shall typically be capable of meeting the following performance criteria, with both channels driven simultaneously, unless otherwise stated: Output power, 8 ohms per channel, 20 Hz-20 kHz, less than 0.1% distortion, at least 375 watts rms per channel. Output power, 4 oh ...
... Each channel of the amplifier shall typically be capable of meeting the following performance criteria, with both channels driven simultaneously, unless otherwise stated: Output power, 8 ohms per channel, 20 Hz-20 kHz, less than 0.1% distortion, at least 375 watts rms per channel. Output power, 4 oh ...
Phone connector (audio)
In electronics, a phone connector, also known as phone jack, audio jack or jack plug, is a common family of connector typically used for analog signals, primarily audio. It is cylindrical in shape, typically with two, three or four contacts. Three-contact versions are known as TRS connectors, where T stands for ""tip"", R stands for ""ring"" and S stands for ""sleeve"". Similarly, two- and four-contact versions are called TS and TRRS connectors respectively.The phone connector was invented for use in telephone switchboards in the 19th century and is still widely used. In its original configuration, the outside diameter of the ""sleeve"" conductor is 1⁄4 inch (exactly 6.35 mm). The ""mini"" connector has a diameter of 3.5 mm (approx. 1⁄8 inch) and the ""sub-mini"" connector has a diameter of 2.5 mm (approx. 3⁄32 inch).