www.cbradio.nl: Manual Onwa KC
... Normally, this control should be set to MAX. position to provide maximum receiver sensitivity for long range reception. However. when communicating with a nearb y station, you may find that the strong signal from this station may cause overloading of your receiver. In such a case, you can use this c ...
... Normally, this control should be set to MAX. position to provide maximum receiver sensitivity for long range reception. However. when communicating with a nearb y station, you may find that the strong signal from this station may cause overloading of your receiver. In such a case, you can use this c ...
SatelliteCommunication - IndiaStudyChannel.com
... observer.[8+8] 3. Write in detail about Altitude and orbit control systems (AOCS).[16] 4. Explain in detail the losses that occur during propagation of EM wave from earth station to satellite and vice versa. In what way they help in satellite communication link design.[16] 5. (a) Define Bits, Symbols ...
... observer.[8+8] 3. Write in detail about Altitude and orbit control systems (AOCS).[16] 4. Explain in detail the losses that occur during propagation of EM wave from earth station to satellite and vice versa. In what way they help in satellite communication link design.[16] 5. (a) Define Bits, Symbols ...
Amateur Radio Technician Class Element 2
... If a receiver mixes a 13.800 MHz VFO with a 14.255 MHz received signal to produce a 455 kHz intermediate frequency (IF) signal, a 13.345 MHz signal will produce an image response in the receiver. (G8B02) • To prevent this many receivers use a tuned preamplifier before the mixer input (sometimes ca ...
... If a receiver mixes a 13.800 MHz VFO with a 14.255 MHz received signal to produce a 455 kHz intermediate frequency (IF) signal, a 13.345 MHz signal will produce an image response in the receiver. (G8B02) • To prevent this many receivers use a tuned preamplifier before the mixer input (sometimes ca ...
Short Wave receiver
... I have inserted a switch which activates the spectrum monitor circuitry when set to SCAN. The monitor circuit settings were made in such a way that the ham band between 7.0 and 7.2 MHz can be visualized on the oscilloscope. ...
... I have inserted a switch which activates the spectrum monitor circuitry when set to SCAN. The monitor circuit settings were made in such a way that the ham band between 7.0 and 7.2 MHz can be visualized on the oscilloscope. ...
High density Luminato receivers for Cable TV and IPTV networks
... Multiservice descrambling Luminato receivers use DVB Common Interface modules to descramble incoming services with DVB scrambling. Receiver models with descrambling capability are equipped with two Common Interface modules slots and two or four satellite, terrestrial or cable inputs. The Common Int ...
... Multiservice descrambling Luminato receivers use DVB Common Interface modules to descramble incoming services with DVB scrambling. Receiver models with descrambling capability are equipped with two Common Interface modules slots and two or four satellite, terrestrial or cable inputs. The Common Int ...
WM-UR802 8 Channel UHF Wireless Microphone
... 8 Channel UHF Wireless Microphone System WM-UR802 Applications: Board room, conference hall, class room, conventional center and religious gathering. ...
... 8 Channel UHF Wireless Microphone System WM-UR802 Applications: Board room, conference hall, class room, conventional center and religious gathering. ...
WM-UR800 8 Channel UHF Wireless Microphone
... individual channels to be used simultaneously (multiple receivers required, 200 point x 8 band =1600 channels). This is perfect for any situation where multiple microphones are required. This system provides the quality and durability required in venues such as a KTV room, karaoke bar, restaurant, o ...
... individual channels to be used simultaneously (multiple receivers required, 200 point x 8 band =1600 channels). This is perfect for any situation where multiple microphones are required. This system provides the quality and durability required in venues such as a KTV room, karaoke bar, restaurant, o ...
Information
... • Can program any number of transmitters to a receiver • High Security Applications • Remote control of garage doors, gates, lights, alarms Description These hand held GIGALINK™ transmitters operate on 27MHz. These GIGALINK™ transmitters can be programmed to the 27MHz Gigalink receivers. The GLT27 s ...
... • Can program any number of transmitters to a receiver • High Security Applications • Remote control of garage doors, gates, lights, alarms Description These hand held GIGALINK™ transmitters operate on 27MHz. These GIGALINK™ transmitters can be programmed to the 27MHz Gigalink receivers. The GLT27 s ...
Didel Ir3x - 3 outputs IR receiver for less than 5 grams planes
... 1mm pitch connectors can be soldered and add 0.10g to the weight (plus 0.08g for the male part). ...
... 1mm pitch connectors can be soldered and add 0.10g to the weight (plus 0.08g for the male part). ...
receivers OF RADIO and TV broadcastING systems
... visual, and machine-generated information over vast distances. Most radios are hardware defined with little or no software control; they are fixed in function for mostly consumer items for broadcast reception. They have a short life and are designed to be discarded and replaced. ...
... visual, and machine-generated information over vast distances. Most radios are hardware defined with little or no software control; they are fixed in function for mostly consumer items for broadcast reception. They have a short life and are designed to be discarded and replaced. ...
FTA receiver
A free-to-air or FTA Receiver is a satellite television receiver designed to receive unencrypted broadcasts. Modern decoders are typically compliant with the MPEG-2/DVB-S and more recently the MPEG-4/DVB-S2 standard for digital television, while older FTA receivers relied on analog satellite transmissions which have declined rapidly in recent years.