correlation fundamentals
... In many ways the C/A code correlation/discriminator/PN tracking system is equivalent to a carrier recovery system using a Phase Locked Loop. A PLL recovery of 1.023Mhz carrier using a 1khz comparison frequency is a good model to use for the GPS code clock recovery. In fact if the equations for secon ...
... In many ways the C/A code correlation/discriminator/PN tracking system is equivalent to a carrier recovery system using a Phase Locked Loop. A PLL recovery of 1.023Mhz carrier using a 1khz comparison frequency is a good model to use for the GPS code clock recovery. In fact if the equations for secon ...
AEC - Q100-004 - Rev-D - Automotive Electronics Council
... If all device pins pass per the failure criteria requirements specified in Section 5 herein, then the following information shall be reported for each pin: ...
... If all device pins pass per the failure criteria requirements specified in Section 5 herein, then the following information shall be reported for each pin: ...
Datasheet - Intersil
... pins to the VON2 supply and a dv/dt-triggered clamp. This dv/dt-triggered clamp imposes a maximum supply turn-on slew rate of 10V/µs. This clamp will trigger if the supply powers up too fast, causing amps of current to flow. Ground and VON1 are treated as I/O pins with this protection scheme. In app ...
... pins to the VON2 supply and a dv/dt-triggered clamp. This dv/dt-triggered clamp imposes a maximum supply turn-on slew rate of 10V/µs. This clamp will trigger if the supply powers up too fast, causing amps of current to flow. Ground and VON1 are treated as I/O pins with this protection scheme. In app ...
MAX5920 -48V Hot-Swap Controller with External R SENSE
... The MAX5920A/MAX5920B provide undervoltage, overvoltage, and overcurrent protection. These devices ensure the input voltage is stable and within tolerance before applying power to the load. Both the MAX5920A and MAX5920B protect a system against overcurrent and short-circuit conditions by turning of ...
... The MAX5920A/MAX5920B provide undervoltage, overvoltage, and overcurrent protection. These devices ensure the input voltage is stable and within tolerance before applying power to the load. Both the MAX5920A and MAX5920B protect a system against overcurrent and short-circuit conditions by turning of ...
Design Strategy For Barrel Shifter Using 2:1 Mux at 45 nm
... Abstract- Designing a mux for low power to use it as a repetitive block in the barrel shifter will considerably reduce the simulation time .our basic objective is to compare existing 2:1 multiplexers with proposed multiplexer design in term of power consumption ,temperature sustainability ,noise imm ...
... Abstract- Designing a mux for low power to use it as a repetitive block in the barrel shifter will considerably reduce the simulation time .our basic objective is to compare existing 2:1 multiplexers with proposed multiplexer design in term of power consumption ,temperature sustainability ,noise imm ...
MAX® 5500 ACRegenerator™ Owner`s Manual
... power. The Voltmeter is Always-On and indicates the incoming line voltage even during an unsafe voltage condition. Readings above 150V will not be accurate due to the meter’s damping characteristics. The Ammeter measures the amount of current being drawn by the connected equipment and the MAX® 5500. ...
... power. The Voltmeter is Always-On and indicates the incoming line voltage even during an unsafe voltage condition. Readings above 150V will not be accurate due to the meter’s damping characteristics. The Ammeter measures the amount of current being drawn by the connected equipment and the MAX® 5500. ...
Radio frequency signals are used for wireless
... Electromechanical isolation prevents RF circuit from leakage or from coupling significantly with actuation circuit. Electromechanical coupling is done electro statically through air because less power is required and is consumed only At the time of actuation MEMS (Micro-Electro-Mechanical-Switch) ac ...
... Electromechanical isolation prevents RF circuit from leakage or from coupling significantly with actuation circuit. Electromechanical coupling is done electro statically through air because less power is required and is consumed only At the time of actuation MEMS (Micro-Electro-Mechanical-Switch) ac ...
LVDT SELECTION, HANDLING AND INSTALLATION GUIDELINES APPLICATION NOTE Preamble
... inherently frictionless, they have a virtually infinite cycle life when properly used. As AC operated LVDTs do not contain any electronics, they can be designed to operate at cryogenic temperatures or up to 1,200°F (650°C), in harsh environments, under high vibration and shock levels. These are the ...
... inherently frictionless, they have a virtually infinite cycle life when properly used. As AC operated LVDTs do not contain any electronics, they can be designed to operate at cryogenic temperatures or up to 1,200°F (650°C), in harsh environments, under high vibration and shock levels. These are the ...
DACs
... reference is multiplied or subdivided, and the speed depends on how fast each level can be selected and established at the output. ...
... reference is multiplied or subdivided, and the speed depends on how fast each level can be selected and established at the output. ...
Lab 1 - Introduction - PSU MNE
... position, etc.). The key to a successful lab experience is to become familiar with the function and operation of the laboratory instruments. Instruments are available for both static and dynamic measurements. Static measurements are satisfactory for parameters that are either constant or changing ve ...
... position, etc.). The key to a successful lab experience is to become familiar with the function and operation of the laboratory instruments. Instruments are available for both static and dynamic measurements. Static measurements are satisfactory for parameters that are either constant or changing ve ...
Interpretation of Datasheet Parameters for ESD Devices
... may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor ...
... may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor ...
Animal Contact Current Mitigation
... (s) "Steady state" means a 1 minute average of RMS voltage or amperage values. (t) "Stray voltage," also referred to as AcV, means the measured difference in an AC electrical potential when measured with a shunt resistor between 2 points that an animal can simultaneously contact in locations normall ...
... (s) "Steady state" means a 1 minute average of RMS voltage or amperage values. (t) "Stray voltage," also referred to as AcV, means the measured difference in an AC electrical potential when measured with a shunt resistor between 2 points that an animal can simultaneously contact in locations normall ...
TPS76701-Q1 数据资料 dataSheet 下载
... with layers 1, 2, 4, 5, 7, and 8 at 5% coverage (0.9 in2) and layers 3 and 6 at 100% coverage (6 in2). For more information, refer to TI technical brief SLMA002. ...
... with layers 1, 2, 4, 5, 7, and 8 at 5% coverage (0.9 in2) and layers 3 and 6 at 100% coverage (6 in2). For more information, refer to TI technical brief SLMA002. ...
