AM2305 - AiT Semiconductor Inc
... AiT Semiconductor Inc. (AiT) reserves the right to make changes to any its product, specifications, to discontinue any integrated circuit product or service without notice, and advises its customers to obtain the latest version of relevant information to verify, before placing orders, that the infor ...
... AiT Semiconductor Inc. (AiT) reserves the right to make changes to any its product, specifications, to discontinue any integrated circuit product or service without notice, and advises its customers to obtain the latest version of relevant information to verify, before placing orders, that the infor ...
SA-600R Series Pure Sine Wave Inverter User`s Manual
... During the AC wiring installation, AC input and output ground wires are connected to the inverter. The AC input ground wire must be connected to the incoming ground from AC utility source. The AC output ground wire should go to the grounding point for your loads (for example, a distribution panel gr ...
... During the AC wiring installation, AC input and output ground wires are connected to the inverter. The AC input ground wire must be connected to the incoming ground from AC utility source. The AC output ground wire should go to the grounding point for your loads (for example, a distribution panel gr ...
Tower Electronic Systems
... When the primary source becomes available again, a linear soft start circuit ensures that there is no inrush current drawn by the UPS. 1.2.2 Inverter The inverter’s input is connected directly to the DC link with which it generates three phase power to support the load. The inverter uses Digital Sig ...
... When the primary source becomes available again, a linear soft start circuit ensures that there is no inrush current drawn by the UPS. 1.2.2 Inverter The inverter’s input is connected directly to the DC link with which it generates three phase power to support the load. The inverter uses Digital Sig ...
1.5 A 280 kHz/560 kHz Boost Regulators
... Boost Regulators The CS5171/2/3/4 products are 280 kHz/560 kHz switching regulators with a high efficiency, 1.5 A integrated switch. These parts operate over a wide input voltage range, from 2.7 V to 30 V. The flexibility of the design allows the chips to operate in most power supply configurations, ...
... Boost Regulators The CS5171/2/3/4 products are 280 kHz/560 kHz switching regulators with a high efficiency, 1.5 A integrated switch. These parts operate over a wide input voltage range, from 2.7 V to 30 V. The flexibility of the design allows the chips to operate in most power supply configurations, ...
AN2839
... specialized IC products. The L6228 is a fully-integrated stepper motor driver IC specifically developed to drive a wide range of two-phase (bipolar) stepper motors. This IC is a onechip, cost-effective solution that includes several unique circuit design features. These features, including a decodin ...
... specialized IC products. The L6228 is a fully-integrated stepper motor driver IC specifically developed to drive a wide range of two-phase (bipolar) stepper motors. This IC is a onechip, cost-effective solution that includes several unique circuit design features. These features, including a decodin ...
IPower Control 2x6 User Guide English www.lindy.co.uk
... Optionally the device can be accessed by using the pearl script “EPC_Control.pl” through the command line (e.g. for automatic or time-triggered switching). ...
... Optionally the device can be accessed by using the pearl script “EPC_Control.pl” through the command line (e.g. for automatic or time-triggered switching). ...
Network Analyzer Basics
... S11 = forward reflection coefficient (input match) S22 = reverse reflection coefficient (output match) S21 = forward transmission coefficient (gain or loss) S12 = reverse transmission coefficient (isolation) ...
... S11 = forward reflection coefficient (input match) S22 = reverse reflection coefficient (output match) S21 = forward transmission coefficient (gain or loss) S12 = reverse transmission coefficient (isolation) ...
module - Autonerdz
... • The scan tool connected to the DLC; there should be 12 volts* at the Tx circuit. • The scan tool connected to the DLC and Engine selected from the Select System menu; there should be 5 volts at the Tx circuit. ...
... • The scan tool connected to the DLC; there should be 12 volts* at the Tx circuit. • The scan tool connected to the DLC and Engine selected from the Select System menu; there should be 5 volts at the Tx circuit. ...
3-phase motor control demonstration board featuring IGBT
... and high voltage. All measuring equipment must be isolated from the mains before powering the board. When using an oscilloscope with the demonstration board, it must be isolated from the AC line. This prevents shock from occurring as a result of touching any SINGLE point in the circuit, but does NOT ...
... and high voltage. All measuring equipment must be isolated from the mains before powering the board. When using an oscilloscope with the demonstration board, it must be isolated from the AC line. This prevents shock from occurring as a result of touching any SINGLE point in the circuit, but does NOT ...
Wirewound Resistors - Pulse Handling Capabilities
... The cross-over point is the time where significant energy starts to be dissipated not only in the wire itself but is now being dissipated into the core, leads, and encapsulation material. This is the point where the pulse is no longer considered a short pulse, but is now considered a long pulse. The ...
... The cross-over point is the time where significant energy starts to be dissipated not only in the wire itself but is now being dissipated into the core, leads, and encapsulation material. This is the point where the pulse is no longer considered a short pulse, but is now considered a long pulse. The ...
LT1940/LT1940L - Dual Monolithic 1.4A, 1.1
... the inductor and operate with higher ripple current. This allows you to use a physically smaller inductor, or one with a lower DCR resulting in higher efficiency. Be aware that if the inductance differs from the simple rule above, then the maximum load current will depend on input voltage. There are ...
... the inductor and operate with higher ripple current. This allows you to use a physically smaller inductor, or one with a lower DCR resulting in higher efficiency. Be aware that if the inductance differs from the simple rule above, then the maximum load current will depend on input voltage. There are ...
DS1817 Active High 3.3V EconoReset FEATURES PIN ASSIGNMENT
... The DS1817 EconoReset uses a precision temperature reference and comparator circuit to monitor the status of the power supply (VCC). When an out-of-tolerance condition is detected, an internal power-fail signal is generated which forces reset to the active state. When VCC returns to an in-tolerance ...
... The DS1817 EconoReset uses a precision temperature reference and comparator circuit to monitor the status of the power supply (VCC). When an out-of-tolerance condition is detected, an internal power-fail signal is generated which forces reset to the active state. When VCC returns to an in-tolerance ...
