ILXGHB Series
... while ensuring a Dust-Tite optical assembly. Three spring tabs provide a tool less mounting system. The lens retaining ring is finished in white UltraClad polyester powder. ...
... while ensuring a Dust-Tite optical assembly. Three spring tabs provide a tool less mounting system. The lens retaining ring is finished in white UltraClad polyester powder. ...
10-12-04 Air Conditioner Bulletin A27
... The positive temperature coefficient resistor/PTCR has replaced the compressor start relay and in some cases the start capacitor. It should be checked in two different ways: ...
... The positive temperature coefficient resistor/PTCR has replaced the compressor start relay and in some cases the start capacitor. It should be checked in two different ways: ...
SDM0230CSP Product Summary Features and Benefits
... Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: ...
... Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: ...
P84467
... Table 2: UL Current Ratings (Strobe Only) Maximum RMS Current (Amps) UL Voltage 135cd 16-33VDC ...
... Table 2: UL Current Ratings (Strobe Only) Maximum RMS Current (Amps) UL Voltage 135cd 16-33VDC ...
ALP20 and ALT20/21 Series, +85°C
... technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained. Although KEMET designs and manufactures its products to the most string ...
... technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained. Although KEMET designs and manufactures its products to the most string ...
Powercut 900
... Equipment and its implementation in accordance with national law, electrical and/or electronic equipment that has reached the end of its life must be disposed of at a recycling facility. As the person responsible for the equipment, it is your responsibility to obtain information on approved collecti ...
... Equipment and its implementation in accordance with national law, electrical and/or electronic equipment that has reached the end of its life must be disposed of at a recycling facility. As the person responsible for the equipment, it is your responsibility to obtain information on approved collecti ...
TSA7887 - Silicon Labs
... Analog Input Channel 1/External VREF Input: In single-channel mode, the AIN1/VREF pin is configured as VREFIN/OUT. In this mode, the TSA7887’s internal 2.5V reference can be accessed or an external reference can be applied to this pin thereby overriding the internal reference. The reference voltage ...
... Analog Input Channel 1/External VREF Input: In single-channel mode, the AIN1/VREF pin is configured as VREFIN/OUT. In this mode, the TSA7887’s internal 2.5V reference can be accessed or an external reference can be applied to this pin thereby overriding the internal reference. The reference voltage ...
BDTIC www.BDTIC.com/infineon AN2012-08 Evaluation Adapter Board for 62mm Half Bridge IGBT Modules
... between the auxiliary collector and the gate of an IGBT module. When the collector-emitter voltage exceeds the diodes breakdown voltage, the diodes current sums up with the current from the driver output. Due to the now increased gate-emitter voltage the transistor is held in an active mode and the ...
... between the auxiliary collector and the gate of an IGBT module. When the collector-emitter voltage exceeds the diodes breakdown voltage, the diodes current sums up with the current from the driver output. Due to the now increased gate-emitter voltage the transistor is held in an active mode and the ...
I - Strand Lighting
... 2.) Dimmer control electronics shall have 16 bit (minimum) fade processing and a dimmer update rate better than 16 ms (60 Hz). Dimmers set to the same level shall output within +/-.5V of each other, regardless of phase or input voltage, providing the desired level is less than the phase input voltag ...
... 2.) Dimmer control electronics shall have 16 bit (minimum) fade processing and a dimmer update rate better than 16 ms (60 Hz). Dimmers set to the same level shall output within +/-.5V of each other, regardless of phase or input voltage, providing the desired level is less than the phase input voltag ...
REVIEW ARTICLE Josephson voltage standards
... Measurement Institutes 共NMIs兲 have decreased over the last 70 years.25–31 The two major improvements coincide with the introduction of single-junction Josephson standards in the early 1970s and the introduction of series-array Josephson standards beginning in 1984. Although the ac Josephson effect p ...
... Measurement Institutes 共NMIs兲 have decreased over the last 70 years.25–31 The two major improvements coincide with the introduction of single-junction Josephson standards in the early 1970s and the introduction of series-array Josephson standards beginning in 1984. Although the ac Josephson effect p ...
Power Electronics - Talking Electronics
... system, it is often desirable and necessary to exercise control over both positive and negative halfcycles. For this purpose, a semiconductor device called triac is used. A triac is a three-terminal semiconductor switching device which can control alternating current in a load. Triac is an abbreviat ...
... system, it is often desirable and necessary to exercise control over both positive and negative halfcycles. For this purpose, a semiconductor device called triac is used. A triac is a three-terminal semiconductor switching device which can control alternating current in a load. Triac is an abbreviat ...
mv motor control centers fvnr spec
... 1.4.3.1 The following information shall be submitted for record purposes at time of shipment: 1.4.3.2 Final as-built drawings and information for items listed in Article 1.3.1. 1.4.3.3 Wiring diagrams. 1.4.3.4 Installation information. 1.4.3.5 Submit six (6) copies of the above information. 1.5 Qual ...
... 1.4.3.1 The following information shall be submitted for record purposes at time of shipment: 1.4.3.2 Final as-built drawings and information for items listed in Article 1.3.1. 1.4.3.3 Wiring diagrams. 1.4.3.4 Installation information. 1.4.3.5 Submit six (6) copies of the above information. 1.5 Qual ...
CISPR Guide
... CISPR 11 is applicable to all types of electrical equipment intended for use in industrial, scientific or medical applications which is operated at frequencies in the frequency range 0 Hz to 400 GHz. Its requirements apply to apparatus and systems in its s cope which are intended for use in resident ...
... CISPR 11 is applicable to all types of electrical equipment intended for use in industrial, scientific or medical applications which is operated at frequencies in the frequency range 0 Hz to 400 GHz. Its requirements apply to apparatus and systems in its s cope which are intended for use in resident ...
Brushless DC Motor Controller (Rev. B)
... chip to modulate either the low-side switches only, or both upper and lower switches, allowing the user to minimize switching losses in less demanding two-quadrant applications. The device includes a differential current-sense amplifier and absolute-value circuit which provide an accurate reconstruc ...
... chip to modulate either the low-side switches only, or both upper and lower switches, allowing the user to minimize switching losses in less demanding two-quadrant applications. The device includes a differential current-sense amplifier and absolute-value circuit which provide an accurate reconstruc ...
