MAX987/MAX988/MAX991/MAX992/MAX995/MAX996 High-Speed, Micropower, Low-Voltage, SOT23, Rail-to-Rail I/O Comparators ________________General Description
... stage that sinks as well as sources current. Large internal output drivers allow rail-to-rail output swing with loads up to 8mA. The MAX988/MAX992/MAX996 have an open-drain output stage that can be pulled beyond VCC to 6V (max) above VEE. These open-drain versions are ideal for level translators and ...
... stage that sinks as well as sources current. Large internal output drivers allow rail-to-rail output swing with loads up to 8mA. The MAX988/MAX992/MAX996 have an open-drain output stage that can be pulled beyond VCC to 6V (max) above VEE. These open-drain versions are ideal for level translators and ...
IOSR Journal of Dental and Medical Sciences (IOSR-JDMS)
... operation. For ideal electrical systems, the supplied power should have perfect current and voltage sinusoidal waveforms, being safe and reliable. The electric utilities can control the voltage levels but, are unable to control the current, since the load profile dictates the shape of the current wa ...
... operation. For ideal electrical systems, the supplied power should have perfect current and voltage sinusoidal waveforms, being safe and reliable. The electric utilities can control the voltage levels but, are unable to control the current, since the load profile dictates the shape of the current wa ...
MAX5038/MAX5041 Dual-Phase, Parallelable, Average Current
... Differential Output Voltage-Sensing Positive Input. Used to sense a remote load. Connect SENSE+ to VOUT+ at the load. The MAX5038 regulates the difference between SENSE+ and SENSE- according to the factory preset output voltage. The MAX5041 regulates the SENSE+ to SENSE- difference to +1.0V. ...
... Differential Output Voltage-Sensing Positive Input. Used to sense a remote load. Connect SENSE+ to VOUT+ at the load. The MAX5038 regulates the difference between SENSE+ and SENSE- according to the factory preset output voltage. The MAX5041 regulates the SENSE+ to SENSE- difference to +1.0V. ...
LM348-N 数据资料 dataSheet 下载
... Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant ...
... Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant ...
MINISTRY OF SCIENCE AND TECHNOLOGY DEPARTMENT OF TECHNICAL AND VOCATIONAL EDUCATION
... A sine wave,f(t), is zero and increasing at t =2.1 ms and the succeeding positive maximum of 8.5 occurs at t =7.5 ms. Express the wave in the from f(t) equals (a) C1 sin(ωt + φ), where φ is positive, as small as possible, and in degrees; (b) C2 cos (ωt + β), where β has the smallest possible magnitu ...
... A sine wave,f(t), is zero and increasing at t =2.1 ms and the succeeding positive maximum of 8.5 occurs at t =7.5 ms. Express the wave in the from f(t) equals (a) C1 sin(ωt + φ), where φ is positive, as small as possible, and in degrees; (b) C2 cos (ωt + β), where β has the smallest possible magnitu ...
High-voltage, High-current Darlington Transistor Array, ULN2003B
... of each respective NPN act as pull-downs and suppress the amount of leakage that may occur from the input. The diodes connected between the output and COM pin is used to suppress the kick-back voltage from an inductive load that is excited when the NPN drivers are turned off (stop sinking) and the s ...
... of each respective NPN act as pull-downs and suppress the amount of leakage that may occur from the input. The diodes connected between the output and COM pin is used to suppress the kick-back voltage from an inductive load that is excited when the NPN drivers are turned off (stop sinking) and the s ...
HSTL16918 9-bit to 18-bit HSTL-to-LVTTL
... Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditi ...
... Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditi ...
OPAx132 High-Speed FET-Input Operational Amplifiers (Rev. B)
... combination of high slew rate and wide bandwidth provide fast settling time. Single, dual, and quad versions have identical specifications for maximum design flexibility. High performance grades are available in the single and dual versions. All are ideal for general-purpose, audio, data acquisition ...
... combination of high slew rate and wide bandwidth provide fast settling time. Single, dual, and quad versions have identical specifications for maximum design flexibility. High performance grades are available in the single and dual versions. All are ideal for general-purpose, audio, data acquisition ...
The 2N4352 is an enhancement mode N-Channel Mosfet
... Note 1 ‐ Absolute maximum ratings are limiting values above which 2N4352 serviceability may be impaired. Note 2 ‐ Device must not be tested at ±125V more than once or longer than 300ms. ...
... Note 1 ‐ Absolute maximum ratings are limiting values above which 2N4352 serviceability may be impaired. Note 2 ‐ Device must not be tested at ±125V more than once or longer than 300ms. ...
ADS5421 数据资料 dataSheet 下载
... data latency of 10 clock cycles after which the output data is available as a 14-bit parallel word either coded in a Straight Offset Binary or Binary Two’s Complement format. The analog input of the ADS5421 consists of a differential track-and-hold circuit, as shown in Figure 1. The differential top ...
... data latency of 10 clock cycles after which the output data is available as a 14-bit parallel word either coded in a Straight Offset Binary or Binary Two’s Complement format. The analog input of the ADS5421 consists of a differential track-and-hold circuit, as shown in Figure 1. The differential top ...
CS1680 Dimmable LED Driver IC for Low-voltage Lighting Features
... Mode1 algorithm regulates value at the trough of the rectified waveform. Mode2 algorithm regulates boost output voltage at the phase cut of each rectified waveform. LED output current begins changing if boost output voltage is outside the Mode3 algorithm regulation range. Accelerated increase in LED ...
... Mode1 algorithm regulates value at the trough of the rectified waveform. Mode2 algorithm regulates boost output voltage at the phase cut of each rectified waveform. LED output current begins changing if boost output voltage is outside the Mode3 algorithm regulation range. Accelerated increase in LED ...
LT1228 - 100MHz Current Feedback Amplifier with DC Gain Control
... to convert the output current to a voltage, which is then amplified with a current feedback amplifier. The LT1228 combines both amplifiers into an 8-pin package, and operates on any supply voltage from 4V (±2V) to 30V (±15V). A complete differential input, gain controlled amplifier can be implemente ...
... to convert the output current to a voltage, which is then amplified with a current feedback amplifier. The LT1228 combines both amplifiers into an 8-pin package, and operates on any supply voltage from 4V (±2V) to 30V (±15V). A complete differential input, gain controlled amplifier can be implemente ...
NCP3127 - PWM Switching Converter
... RSET = Current set resistor The RSET values range from 5 kW to 55 kW. If RSET is not connected, the device switches the OCP threshold to a fixed 375 mV value (3.57 A), an internal safety clamp on ISET is triggered as soon as ISET voltage reaches 700 mV, enabling the 375 mV fixed threshold and ending ...
... RSET = Current set resistor The RSET values range from 5 kW to 55 kW. If RSET is not connected, the device switches the OCP threshold to a fixed 375 mV value (3.57 A), an internal safety clamp on ISET is triggered as soon as ISET voltage reaches 700 mV, enabling the 375 mV fixed threshold and ending ...
ADA4861-3
... The maximum safe power dissipation for the ADA4861-3 is limited by the associated rise in junction temperature (TJ) on the die. At approximately 150°C, which is the glass transition temperature, the plastic changes its properties. Even temporarily exceeding this temperature limit can change the stre ...
... The maximum safe power dissipation for the ADA4861-3 is limited by the associated rise in junction temperature (TJ) on the die. At approximately 150°C, which is the glass transition temperature, the plastic changes its properties. Even temporarily exceeding this temperature limit can change the stre ...
Name - Bowles Physics
... Part I – Using Ohm’s Law Obtain a resistor with the code Brown-Black-Brown and record its resistance in the data table. Place the resistor into a pair of springs. Attach 1 wire in between the batteries so that you use BOTH batteries. Attach 1 wire from the positive terminal of the first battery to o ...
... Part I – Using Ohm’s Law Obtain a resistor with the code Brown-Black-Brown and record its resistance in the data table. Place the resistor into a pair of springs. Attach 1 wire in between the batteries so that you use BOTH batteries. Attach 1 wire from the positive terminal of the first battery to o ...
AP_Physics_B_-_Series_Circuit_Lab
... Part I – Using Ohm’s Law 1. Obtain a resistor with the code Brown-Black-Brown and record its resistance in the data table. 2. Place the resistor into a pair of springs. 3. Attach 1 wire in between the batteries so that you use BOTH batteries. 4. Attach 1 wire from the positive terminal of the first ...
... Part I – Using Ohm’s Law 1. Obtain a resistor with the code Brown-Black-Brown and record its resistance in the data table. 2. Place the resistor into a pair of springs. 3. Attach 1 wire in between the batteries so that you use BOTH batteries. 4. Attach 1 wire from the positive terminal of the first ...
AD7367 数据手册DataSheet下载
... simultaneously appears on both pins from the simultaneous conversions of both ADCs. The data stream consists of the 14 bits of conversion data and is provided MSB first. If CS is held low for a further 14 SCLK cycles on either DOUTA or DOUTB, the data from the other ADC follows on the DOUT pin. This ...
... simultaneously appears on both pins from the simultaneous conversions of both ADCs. The data stream consists of the 14 bits of conversion data and is provided MSB first. If CS is held low for a further 14 SCLK cycles on either DOUTA or DOUTB, the data from the other ADC follows on the DOUT pin. This ...
Schmitt trigger
In electronics a Schmitt trigger is a comparator circuit with hysteresis implemented by applying positive feedback to the noninverting input of a comparator or differential amplifier. It is an active circuit which converts an analog input signal to a digital output signal. The circuit is named a ""trigger"" because the output retains its value until the input changes sufficiently to trigger a change. In the non-inverting configuration, when the input is higher than a chosen threshold, the output is high. When the input is below a different (lower) chosen threshold the output is low, and when the input is between the two levels the output retains its value. This dual threshold action is called hysteresis and implies that the Schmitt trigger possesses memory and can act as a bistable multivibrator (latch or flip-flop). There is a close relation between the two kinds of circuits: a Schmitt trigger can be converted into a latch and a latch can be converted into a Schmitt trigger.Schmitt trigger devices are typically used in signal conditioning applications to remove noise from signals used in digital circuits, particularly mechanical contact bounce. They are also used in closed loop negative feedback configurations to implement relaxation oscillators, used in function generators and switching power supplies.