THS3201-EP
... The THS3201 is a wide-band, high-speed current-feedback amplifier, designed to operate over a wide supply range of ±3.3 V to ±7.5 V for today's high-performance applications. The wide supply range, combined with low distortion and high slew rate, makes the THS3201 ideally suited for arbitrary wavefo ...
... The THS3201 is a wide-band, high-speed current-feedback amplifier, designed to operate over a wide supply range of ±3.3 V to ±7.5 V for today's high-performance applications. The wide supply range, combined with low distortion and high slew rate, makes the THS3201 ideally suited for arbitrary wavefo ...
General Description Features
... The average current-mode control technique offers inherently stable operation, reduces component derating and size by accurately controlling the inductor current. The devices achieve high efficiency at high currents (up to 30A) with a minimum number of external components. A logic input (MODE) allow ...
... The average current-mode control technique offers inherently stable operation, reduces component derating and size by accurately controlling the inductor current. The devices achieve high efficiency at high currents (up to 30A) with a minimum number of external components. A logic input (MODE) allow ...
MAX4631/MAX4632/MAX4633 Fault-Protected, High-Voltage, Dual Analog Switches General Description
... analog switches are pin compatible with the industry-standard DG401/DG403/DG405. They upgrade the existing devices with fault-protected inputs and Rail-to-Rail® signal handling capabilities. The MAX4631/MAX4632/MAX4633’s normally open (NO) and normally closed (NC) terminals are protected from overvo ...
... analog switches are pin compatible with the industry-standard DG401/DG403/DG405. They upgrade the existing devices with fault-protected inputs and Rail-to-Rail® signal handling capabilities. The MAX4631/MAX4632/MAX4633’s normally open (NO) and normally closed (NC) terminals are protected from overvo ...
SN65HVD11-HT - Texas Instruments
... The SN65HVD11-HT device combines a 3-state differential line driver and differential input line receiver that operates with a single 3.3-V power supply. It is designed for balanced transmission lines and meets or exceeds ANSI TIA/EIA-485-A and ISO 8482:1993, with the exception that the thermal shutd ...
... The SN65HVD11-HT device combines a 3-state differential line driver and differential input line receiver that operates with a single 3.3-V power supply. It is designed for balanced transmission lines and meets or exceeds ANSI TIA/EIA-485-A and ISO 8482:1993, with the exception that the thermal shutd ...
Dynaco Stereo 70 Repair Guide
... etc.) you should review our Stereo 70 Troubleshooting Repair Guide available at our website. The most problematic components in the Dynaco power amplifiers are (in order of severity) the Quad electrolytic capacitor, selenium rectifier, output tube sockets, output tubes, and driver pc board. Of those ...
... etc.) you should review our Stereo 70 Troubleshooting Repair Guide available at our website. The most problematic components in the Dynaco power amplifiers are (in order of severity) the Quad electrolytic capacitor, selenium rectifier, output tube sockets, output tubes, and driver pc board. Of those ...
4-Channel, 625 kSPS, 12-Bit Parallel ADC with a Sequencer AD7934-6
... enabled. Data and the channel ID are transferred on Pin DB0 to Pin DB7, and Pin DB8/HBEN assumes its HBEN functionality. When operating in byte transfer mode, unused data lines should be tied off to DGND. Data Bit 0 to Data Bit 7. Three-state parallel digital I/O pins that provide the conversion res ...
... enabled. Data and the channel ID are transferred on Pin DB0 to Pin DB7, and Pin DB8/HBEN assumes its HBEN functionality. When operating in byte transfer mode, unused data lines should be tied off to DGND. Data Bit 0 to Data Bit 7. Three-state parallel digital I/O pins that provide the conversion res ...
MAX5100 +2.7V to +5.5V, Low-Power, Quad, Parallel General Description
... less than the reference input resistance. To keep within 1LSB error in an 8-bit system, RS must be less than RREF / 256. Hence, maintain a value of RS <1kΩ to ensure 8-bit accuracy. If VREF is DC only, bypass REF to GND with a 0.1µF capacitor. Values greater than this improve noise rejection. ...
... less than the reference input resistance. To keep within 1LSB error in an 8-bit system, RS must be less than RREF / 256. Hence, maintain a value of RS <1kΩ to ensure 8-bit accuracy. If VREF is DC only, bypass REF to GND with a 0.1µF capacitor. Values greater than this improve noise rejection. ...
74LCXH245 Low Voltage Bidirectional Transceiver with Bushold 7 4LCXH
... buffers with 3-STATE outputs and is intended for bus oriented applications. The device is designed for low voltage (2.5V and 3.3V) VCC applications. The T/R input determines the direction of data flow through the device. The OE input disables both the A and B ports by placing them in a high impedanc ...
... buffers with 3-STATE outputs and is intended for bus oriented applications. The device is designed for low voltage (2.5V and 3.3V) VCC applications. The T/R input determines the direction of data flow through the device. The OE input disables both the A and B ports by placing them in a high impedanc ...
HMC377QS16G 数据资料DataSheet下载
... The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top ...
... The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top ...
file_46198 - Teaching Advanced Physics
... Back to reality After a lot of maths, there is a danger that students will lose sight of the fact that capacitors are common components with a wide range of uses. ...
... Back to reality After a lot of maths, there is a danger that students will lose sight of the fact that capacitors are common components with a wide range of uses. ...
Manual
... The patented THRUST® function can be switched in and out via the front panel as well, applying a high pass filter before the RMS detector circuit that preserves that punchy bottom end. A SIDE CHAIN input is provided for keying and external detector path processing. The 527 Compressor sections of two ...
... The patented THRUST® function can be switched in and out via the front panel as well, applying a high pass filter before the RMS detector circuit that preserves that punchy bottom end. A SIDE CHAIN input is provided for keying and external detector path processing. The 527 Compressor sections of two ...
Phototriac
... isolation between the TRIAC output and input driving LED, and the need to reduce board real estate, a ZC phototriac looks very attractive as illustrated in the two schematics of figure 15 and figure 16. ...
... isolation between the TRIAC output and input driving LED, and the need to reduce board real estate, a ZC phototriac looks very attractive as illustrated in the two schematics of figure 15 and figure 16. ...
ABUT
... switch action for almost any type of dc-dc converter. A complete pulse-width modulation block creates a PWM switching function, with adjustable frequency and duty ratio. As in the SCR circuit, this means that the terminals of the FET can be connected to any voltage level up to the device ratings. Th ...
... switch action for almost any type of dc-dc converter. A complete pulse-width modulation block creates a PWM switching function, with adjustable frequency and duty ratio. As in the SCR circuit, this means that the terminals of the FET can be connected to any voltage level up to the device ratings. Th ...
VCA810 数据资料 dataSheet 下载
... Operating from ±5V supplies, the gain control voltage for the VCA810 will adjust the gain from –40dB at 0V input to +40dB at –2V input. Increasing the control voltage above ground will attenuate the signal path to greater than 80dB. Signal bandwidth and slew rate remain constant over the entire gain ...
... Operating from ±5V supplies, the gain control voltage for the VCA810 will adjust the gain from –40dB at 0V input to +40dB at –2V input. Increasing the control voltage above ground will attenuate the signal path to greater than 80dB. Signal bandwidth and slew rate remain constant over the entire gain ...
AE-2 Draft of Section 22 9/24/08
... injection transformer to form an insulated secondary winding. It should be low enough in impedance to achieve the test level and waveform. Core Wire An individual wire inside a shield. The individual wire induced voltages/currents are reduced from the driven loop voltages/currents by the presence of ...
... injection transformer to form an insulated secondary winding. It should be low enough in impedance to achieve the test level and waveform. Core Wire An individual wire inside a shield. The individual wire induced voltages/currents are reduced from the driven loop voltages/currents by the presence of ...
OPA3691 Triple Wideband, Current-Feedback OPERATIONAL AMPLIFIER With Disable FEATURES
... delivers a high output current with minimal voltage headroom and crossover distortion. This gives exceptional singlesupply operation. Using a single +5V supply, the OPA3691 can deliver a 1V to 4V output swing with over 120mA drive current and 150MHz bandwidth. This combination of features makes the ...
... delivers a high output current with minimal voltage headroom and crossover distortion. This gives exceptional singlesupply operation. Using a single +5V supply, the OPA3691 can deliver a 1V to 4V output swing with over 120mA drive current and 150MHz bandwidth. This combination of features makes the ...
Oscilloscope history
This article discusses the history and development of oscilloscope technology.