500 MHz Four-Quadrant Multiplier AD834 Data Sheet FEATURES
... CERDIP, operates over the military temperature range of −55°C to +125°C. S-grade chips are also available. Two application notes featuring the AD834 (AN-212 and AN-216) can be found at www.analog.com. For additional applications circuits, consult the AD811 data sheet. ...
... CERDIP, operates over the military temperature range of −55°C to +125°C. S-grade chips are also available. Two application notes featuring the AD834 (AN-212 and AN-216) can be found at www.analog.com. For additional applications circuits, consult the AD811 data sheet. ...
ADA4922-1 数据手册DataSheet 下载
... The ADA4922-1 is a differential driver for 16-bit to 18-bit ADCs that have differential input ranges up to ±20 V. Configured as an easy-to-use, single-ended-to-differential amplifier, the ADA4922-1 requires no external components to drive ADCs. The ADA4922-1 provides essential benefits such as low d ...
... The ADA4922-1 is a differential driver for 16-bit to 18-bit ADCs that have differential input ranges up to ±20 V. Configured as an easy-to-use, single-ended-to-differential amplifier, the ADA4922-1 requires no external components to drive ADCs. The ADA4922-1 provides essential benefits such as low d ...
design_review
... The data sheet provided by Texas Instruments outlined a general design procedure and external circuit set-up. The values of each analog component were chosen as follows: The output voltage is programmed by selecting R1 and R2 such that ...
... The data sheet provided by Texas Instruments outlined a general design procedure and external circuit set-up. The values of each analog component were chosen as follows: The output voltage is programmed by selecting R1 and R2 such that ...
Keysight 1GC1-4268 DC - 12 GHz Packaged Divide-by
... sinusoidal input signal over a 200 MHz to 12 GHz bandwidth. Below 200 MHz the prescaler input is “slew–rate” limited, requiring fast rising and falling edge speeds to properly divide. The device will operate at frequencies down to DC when driven with a square–wave. Due to the presence of an off–chip ...
... sinusoidal input signal over a 200 MHz to 12 GHz bandwidth. Below 200 MHz the prescaler input is “slew–rate” limited, requiring fast rising and falling edge speeds to properly divide. The device will operate at frequencies down to DC when driven with a square–wave. Due to the presence of an off–chip ...
Visio-ALD-214012PJ132 (CTR-4474-X) Instruction - TDK
... ●This product is designed for driving LED backlight systems. Do not use it with any other load. ●Store this product under the conditions defined in the specification document. ●Do not store this product in an environment where dust, dirt or corrosive gas(salt,acid,base, etc.) is present. ●This produ ...
... ●This product is designed for driving LED backlight systems. Do not use it with any other load. ●Store this product under the conditions defined in the specification document. ●Do not store this product in an environment where dust, dirt or corrosive gas(salt,acid,base, etc.) is present. ●This produ ...
Another W97M/Cartman.Poppy Infected Document
... To change the attribute values of devices 1 Double-click the attribute value (0V) of the VDC symbol, V1. 2 In the Set Attribute Value dialog box, type 5V. 3 Click OK. 4 Continue changing the attribute values of the circuit devices until all devices are named as in Fig.2. Your schematic should now ha ...
... To change the attribute values of devices 1 Double-click the attribute value (0V) of the VDC symbol, V1. 2 In the Set Attribute Value dialog box, type 5V. 3 Click OK. 4 Continue changing the attribute values of the circuit devices until all devices are named as in Fig.2. Your schematic should now ha ...
A Compact Low Voltage CMOS Four-Quadrant Analog Multiplier
... two identical voltage controlled square root blocks which operate as non-linear cancellation paths. Injecting the output currents of the input transistors into the square root blocks, a differential output current of the overall circuit will become a multiplication function of two input signals V12 ...
... two identical voltage controlled square root blocks which operate as non-linear cancellation paths. Injecting the output currents of the input transistors into the square root blocks, a differential output current of the overall circuit will become a multiplication function of two input signals V12 ...
Class I, II, and III Dielectric Capacitor Codes
... Top 8 Capacitor Concepts Do not use the property of magnetism like inductors do! Capacitors store energy in an electrostatic field instead The number of electrons it can store in this field determines its capacitance size The units of Capacitance are measured in Farads [F] and the symbol fo ...
... Top 8 Capacitor Concepts Do not use the property of magnetism like inductors do! Capacitors store energy in an electrostatic field instead The number of electrons it can store in this field determines its capacitance size The units of Capacitance are measured in Farads [F] and the symbol fo ...
315MHz/433MHz ASK Superheterodyne Receiver with Extended Dynamic Range General Description Features
... frequency range. Its signal range is from -114dBm to 0dBm. With few external components and a low-current power-down mode, it is ideal for cost- and power-sensitive applications typical in the automotive and consumer markets. The chip consists of a low-noise amplifier (LNA), a fully differential ima ...
... frequency range. Its signal range is from -114dBm to 0dBm. With few external components and a low-current power-down mode, it is ideal for cost- and power-sensitive applications typical in the automotive and consumer markets. The chip consists of a low-noise amplifier (LNA), a fully differential ima ...
NL1036_NL7171
... Heat Conditioning - Before applying voltage, heat anode stud to 100-1250C (keeping cathode near room temperature) for two hours minimum. This drives mercury away from anode and anode seal area. Voltage Conditioning (after Heat Conditioning) - Apply 110% of operating voltage (preferably DCV) or up to ...
... Heat Conditioning - Before applying voltage, heat anode stud to 100-1250C (keeping cathode near room temperature) for two hours minimum. This drives mercury away from anode and anode seal area. Voltage Conditioning (after Heat Conditioning) - Apply 110% of operating voltage (preferably DCV) or up to ...
Difet OPA121 Low Cost Precision OPERATIONAL AMPLIFIER
... warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or ...
... warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or ...
AD2S83: 数据手册DataSheet 下载
... The position output from the converter is presented via 3-state output pins which can be configured for operations with 8- or 16-bit bus. BYTE SELECT, ENABLE and INHIBIT pins ensure easy data transfer to 8- and 16-bit data bus, and outputs are provided to allow for cycle or pitch counting in externa ...
... The position output from the converter is presented via 3-state output pins which can be configured for operations with 8- or 16-bit bus. BYTE SELECT, ENABLE and INHIBIT pins ensure easy data transfer to 8- and 16-bit data bus, and outputs are provided to allow for cycle or pitch counting in externa ...
Clamp-on Testers - nbn Elektronik AG
... Influence of external magnetic field 0.01% or less (on current value of adjacent cable) 0.0005% typical*1 (on current value of adjacent cable) ...
... Influence of external magnetic field 0.01% or less (on current value of adjacent cable) 0.0005% typical*1 (on current value of adjacent cable) ...
PURE SINE WAVE INVERTER FOR HOUSE BACKUP
... Easy to Generate – PWM signals are quite easy to generate. Many modern microcontrollers include PWM hardware within the chip; using this hardware often takes very little attention from the microprocessor and it can run in the background without interfering with executing code. PWM signals are also ...
... Easy to Generate – PWM signals are quite easy to generate. Many modern microcontrollers include PWM hardware within the chip; using this hardware often takes very little attention from the microprocessor and it can run in the background without interfering with executing code. PWM signals are also ...
g PWM Output Accelerometer ADXL212
... The ADXL212 is a high precision, low power, complete dual axis accelerometer with signal conditioned, duty cycle modulated outputs, all on a single monolithic IC. The ADXL212 measures acceleration with a full-scale range of ±2 g (typical). The ADXL212 measures both dynamic acceleration (such as vibr ...
... The ADXL212 is a high precision, low power, complete dual axis accelerometer with signal conditioned, duty cycle modulated outputs, all on a single monolithic IC. The ADXL212 measures acceleration with a full-scale range of ±2 g (typical). The ADXL212 measures both dynamic acceleration (such as vibr ...
4-bit dual supply level translator without direction control pin
... impedance of the output at HIGH state depends on the pull-up resistor placed at the I/Os. As the device has pull-up resistors on both the I/OVCC and I/OVL ports, the user needs to ensure that the driver is able to sink the required amount of current. For example, if the settings are VCC = 5.5 V, VL ...
... impedance of the output at HIGH state depends on the pull-up resistor placed at the I/Os. As the device has pull-up resistors on both the I/OVCC and I/OVL ports, the user needs to ensure that the driver is able to sink the required amount of current. For example, if the settings are VCC = 5.5 V, VL ...
GSK-24 Logic Probe Kit The purpose of a logic probe is to examine
... Before the pulse detector circuit are two inverters. They perform a number of functions. They shape the level change into a sharp pulse and put out signals at rail voltage. Any change of level (low to high or high to low) at the probe will cause one inverter to go high and the other to go low. By ad ...
... Before the pulse detector circuit are two inverters. They perform a number of functions. They shape the level change into a sharp pulse and put out signals at rail voltage. Any change of level (low to high or high to low) at the probe will cause one inverter to go high and the other to go low. By ad ...
INCREASE OF STRAIN GAGE OUTPUT VOLTAGE SIGNALS ACCURACY
... In measurement of sample deformation strain gages convert sample deformation into the resistance change. This resistance change is usually small (permitted strain gage deformation is 0,1 %), therefore the resistance change is measured in bridge configuration where measured signals are small and nois ...
... In measurement of sample deformation strain gages convert sample deformation into the resistance change. This resistance change is usually small (permitted strain gage deformation is 0,1 %), therefore the resistance change is measured in bridge configuration where measured signals are small and nois ...
50 μA, 2 mm × 1.7 mm WLCSP, Low Noise, Heart Rate Monitor for
... Reference Buffer Input. Use REFIN, a high impedance input terminal, to set the level of the reference buffer. High-Pass Sense Input for Instrumentation Amplifier. Connect HPSENSE to the junction of R and C that sets the corner frequency of the dc blocking circuit. High-Pass Driver Output. Connect HP ...
... Reference Buffer Input. Use REFIN, a high impedance input terminal, to set the level of the reference buffer. High-Pass Sense Input for Instrumentation Amplifier. Connect HPSENSE to the junction of R and C that sets the corner frequency of the dc blocking circuit. High-Pass Driver Output. Connect HP ...
Oscilloscope history
This article discusses the history and development of oscilloscope technology.