BD63940EFV
... Users should be aware that this series has been designed to expose their frames at the back of the package, and should be used with suitable heat dissipation treatment in this area to improve dissipation. As large a dissipation pattern should be taken as possible, not only on the front of the basebo ...
... Users should be aware that this series has been designed to expose their frames at the back of the package, and should be used with suitable heat dissipation treatment in this area to improve dissipation. As large a dissipation pattern should be taken as possible, not only on the front of the basebo ...
Document
... It is apparent from equations 4.4a and 4.4b that, once the power level has been fixed by the DC supply voltage Ud and the maximum load current iLmax, the switching frequency fs is an important design parameter. It is discussed in Section 4.4.6 that fs must be high enough to ensure that the switching ...
... It is apparent from equations 4.4a and 4.4b that, once the power level has been fixed by the DC supply voltage Ud and the maximum load current iLmax, the switching frequency fs is an important design parameter. It is discussed in Section 4.4.6 that fs must be high enough to ensure that the switching ...
Technical Data Sheet
... servicing purposes. If less than 12” is available, an optional remote room temperature sensor is recommended. • Heater may be recessed into a wall but do not enclose obstruct access to heaters front panel and grill. • Weight of heater must be considered when selecting placement location. Refer to ...
... servicing purposes. If less than 12” is available, an optional remote room temperature sensor is recommended. • Heater may be recessed into a wall but do not enclose obstruct access to heaters front panel and grill. • Weight of heater must be considered when selecting placement location. Refer to ...
AN-EVAL3GS03LJG
... Drain to source voltage and current @ maximum load................................................................. 22 Load transient response (Dynamic load from 10% to 100%) ....................................................... 23 Output ripple voltage at maximum load .......................... ...
... Drain to source voltage and current @ maximum load................................................................. 22 Load transient response (Dynamic load from 10% to 100%) ....................................................... 23 Output ripple voltage at maximum load .......................... ...
SP385A
... the input logic levels. Typically the RS-232 output voltage swing is ±9V for 5V supply and ±4.2V for 3.3V supply. Even under worst case loading conditions of 3kΩ and 2500pF, the output is guaranteed to be ±5V for a 5V supply and ±3.7V for a 3.3V supply which adheres to EIA-232 and EIA562 specificati ...
... the input logic levels. Typically the RS-232 output voltage swing is ±9V for 5V supply and ±4.2V for 3.3V supply. Even under worst case loading conditions of 3kΩ and 2500pF, the output is guaranteed to be ±5V for a 5V supply and ±3.7V for a 3.3V supply which adheres to EIA-232 and EIA562 specificati ...
Find the Right Fuse!
... Circuitry overcurrent protection rarely receives the attention it deserves. An inadequately thought out selection of fuses can lead to the breakdown of equipment and installation, resulting in high replacement costs and dissatisfied customers. This technical article focuses on the correct selection ...
... Circuitry overcurrent protection rarely receives the attention it deserves. An inadequately thought out selection of fuses can lead to the breakdown of equipment and installation, resulting in high replacement costs and dissatisfied customers. This technical article focuses on the correct selection ...
BDTIC 6ED003L06-F Gate Drive IC for three phase converters -
... to the reference voltage (pin VSx) and the bias voltage (pin VBx). The internal structure of the output driver itself is the same as for all three low voltage output pins. Please note, that there is a parasitic connection from each high side to the low side control area, which is not given in Figure ...
... to the reference voltage (pin VSx) and the bias voltage (pin VBx). The internal structure of the output driver itself is the same as for all three low voltage output pins. Please note, that there is a parasitic connection from each high side to the low side control area, which is not given in Figure ...
Dist Training materials HK & China Jun 07 Ver3.0
... Bipolar- Leader in Power Density and Space Efficiency ...
... Bipolar- Leader in Power Density and Space Efficiency ...
You are required to lead a lab activity with the class
... - It fill up faster with higher currents - Only will fill up to the supplied voltage - Larger capacitors take longer to charge Show the circuit diagram representation of the capacitor - Be sure to emphasize the polarity of the capacitor and how the long lead is the positive one. Have students look a ...
... - It fill up faster with higher currents - Only will fill up to the supplied voltage - Larger capacitors take longer to charge Show the circuit diagram representation of the capacitor - Be sure to emphasize the polarity of the capacitor and how the long lead is the positive one. Have students look a ...
INA19xA-Q1: Current Shunt Monitors With -16-V to 80
... Figure 20. INA19xA Basic Connections 7.3.2 Selecting RS The value chosen for the shunt resistor, RS, depends on the application and is a compromise between smallsignal accuracy and maximum permissible voltage loss in the measurement line. High values of RS provide better accuracy at lower currents b ...
... Figure 20. INA19xA Basic Connections 7.3.2 Selecting RS The value chosen for the shunt resistor, RS, depends on the application and is a compromise between smallsignal accuracy and maximum permissible voltage loss in the measurement line. High values of RS provide better accuracy at lower currents b ...
262900 - Low Medium Voltage Motor Controlers
... For motors shut down by the fire alarm system; refer to Division 28 31 00 Fire Alarm Systems. Meet building control systems requirements. ...
... For motors shut down by the fire alarm system; refer to Division 28 31 00 Fire Alarm Systems. Meet building control systems requirements. ...
Alternating current
Alternating current (AC), is an electric current in which the flow of electric charge periodically reverses direction, whereas in direct current (DC, also dc), the flow of electric charge is only in one direction. The abbreviations AC and DC are often used to mean simply alternating and direct, as when they modify current or voltage.AC is the form in which electric power is delivered to businesses and residences. The usual waveform of alternating current in most electric power circuits is a sine wave. In certain applications, different waveforms are used, such as triangular or square waves. Audio and radio signals carried on electrical wires are also examples of alternating current. These types of alternating current carry information encoded (or modulated) onto the AC signal, such as sound (audio) or images (video).