UNISONIC TECHNOLOGIES CO., LTD MC34118
... To distinguish speech (consists of bursts) from background noise (a relatively constant signal level) is the main purpose of the background noise monitors. There is one background noise monitor for the receive path and another one for the transmit path. The receive background noise monitor is operat ...
... To distinguish speech (consists of bursts) from background noise (a relatively constant signal level) is the main purpose of the background noise monitors. There is one background noise monitor for the receive path and another one for the transmit path. The receive background noise monitor is operat ...
100+100W stereo BASH® power amplifier
... Notice that normally only one Digital Converter is needed to supply a stereo or multi-channel amplifier system, therefore most of the functions implemented in the circuit have summing outputs The signal circuits are biased by fixed negative and positive voltages referred to Ground. Instead the final ...
... Notice that normally only one Digital Converter is needed to supply a stereo or multi-channel amplifier system, therefore most of the functions implemented in the circuit have summing outputs The signal circuits are biased by fixed negative and positive voltages referred to Ground. Instead the final ...
Precision Lowest Cost ISOLATION AMPLIFIER FEATURES
... Each power supply pin should be bypassed with 1µF tantalum capacitors located as close to the amplifier as possible. The internal frequency of the modulator/demodulator is set at 500kHz by an internal oscillator. Therefore, if it is desired to minimize any feedthrough noise (beat frequencies) from a ...
... Each power supply pin should be bypassed with 1µF tantalum capacitors located as close to the amplifier as possible. The internal frequency of the modulator/demodulator is set at 500kHz by an internal oscillator. Therefore, if it is desired to minimize any feedthrough noise (beat frequencies) from a ...
SP6644/6645 Evaluation Board Manual
... The SP6644/6645 Evaluation Board is designed to help the user evaluate the performance of the SP6644/6645 for use as a single or dual cell input to +3.3V output DC-DC Converter. The output of the SP6644/6645 is preset to +3.3V or can be adjusted from +2V to +5.5V by manipulating two external resisto ...
... The SP6644/6645 Evaluation Board is designed to help the user evaluate the performance of the SP6644/6645 for use as a single or dual cell input to +3.3V output DC-DC Converter. The output of the SP6644/6645 is preset to +3.3V or can be adjusted from +2V to +5.5V by manipulating two external resisto ...
SP4446 High Output Voltage Boost Regulator LCD Bias
... the FB pin to minimize copper trace connections that can inject noise into the system. The ground connection for the feedback resistor network should connect directly to the GND pin or to an analog ground plane that is tied directly to the GND pin. The inductor and the Schottky diode should be place ...
... the FB pin to minimize copper trace connections that can inject noise into the system. The ground connection for the feedback resistor network should connect directly to the GND pin or to an analog ground plane that is tied directly to the GND pin. The inductor and the Schottky diode should be place ...
AD8605 数据手册DataSheet 下载
... Changes to Figure 13, Figure 14, and Figure 16 Captions .... 10 Changes to Figure 15, Figure 17, and Figure 18 ..................... 10 Changes to Figure 34 and Figure 35 Captions........................ 13 Changes to Figure 36 ................................................................. 13 Cha ...
... Changes to Figure 13, Figure 14, and Figure 16 Captions .... 10 Changes to Figure 15, Figure 17, and Figure 18 ..................... 10 Changes to Figure 34 and Figure 35 Captions........................ 13 Changes to Figure 36 ................................................................. 13 Cha ...
TQP3M9037 数据资料DataSheet下载
... 1. See PC Board Layout for more information. 2. R3 (0 Ω jumper) is not shown on the schematic and may be replaced with copper trace in the target application layout. 3. All components are of 0402 size unless stated on the schematic. 4. C1, C2, and C3 are non-critical values. The reactive impedance s ...
... 1. See PC Board Layout for more information. 2. R3 (0 Ω jumper) is not shown on the schematic and may be replaced with copper trace in the target application layout. 3. All components are of 0402 size unless stated on the schematic. 4. C1, C2, and C3 are non-critical values. The reactive impedance s ...
