AMC1203 数据资料 dataSheet 下载
... This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete devi ...
... This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete devi ...
Analog Dialogue Volume 43, Number 2, 2009
... The PLC evaluation system3 described here integrates all the stages needed to generate a complete input/output design. It contains four fully isolated ADC channels, an ARM7™ microprocessor with RS-232 interface, and four fully isolated DAC output channels. The board is powered by a dc supply. Hardwa ...
... The PLC evaluation system3 described here integrates all the stages needed to generate a complete input/output design. It contains four fully isolated ADC channels, an ARM7™ microprocessor with RS-232 interface, and four fully isolated DAC output channels. The board is powered by a dc supply. Hardwa ...
17-V, 1.5-A, SYNCHRONOUS STEP-DOWN
... In constant frequency mode, the output voltage is regulated by varying the duty cycle of the PWM signal in the range of 100% to 10%. Connecting the SYNC pin to a voltage greater than 1.5 V forces the converter to operate permanently in the PWM mode even at light or no-load currents. The advantage is ...
... In constant frequency mode, the output voltage is regulated by varying the duty cycle of the PWM signal in the range of 100% to 10%. Connecting the SYNC pin to a voltage greater than 1.5 V forces the converter to operate permanently in the PWM mode even at light or no-load currents. The advantage is ...
SIMULATION OF LCC RESONANT CIRCUITS PURPOSE POWER ELECTRONICS ECE562 COLORADO STATE UNIVERSITY
... Doesn’t this violate the “Conservation of Energy” concept? Answer: No, it doesn’t. Power can only be dissipated in R, since L, Cp and Cs are considered non-lossy, or ideal. In Figure 10, the input current peaks at -19.215 dB(Amps) = 109.5 mA, so input power would be 109.5 mW. This makes it look like ...
... Doesn’t this violate the “Conservation of Energy” concept? Answer: No, it doesn’t. Power can only be dissipated in R, since L, Cp and Cs are considered non-lossy, or ideal. In Figure 10, the input current peaks at -19.215 dB(Amps) = 109.5 mA, so input power would be 109.5 mW. This makes it look like ...
DRV600 数据资料 dataSheet 下载
... Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such informati ...
... Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such informati ...
ADM3485E 数据手册DataSheet 下载
... The ADM3485E is a 3.3 V, low power data transceiver with ±15 kV ESD protection, suitable for half-duplex communication on multipoint bus transmission lines. The ADM3485E is designed for balanced data transmission and complies with TIA/EIA standards RS485 and RS-422. The ADM3485E is a half-duplex tr ...
... The ADM3485E is a 3.3 V, low power data transceiver with ±15 kV ESD protection, suitable for half-duplex communication on multipoint bus transmission lines. The ADM3485E is designed for balanced data transmission and complies with TIA/EIA standards RS485 and RS-422. The ADM3485E is a half-duplex tr ...
ADS822 数据资料 dataSheet 下载
... With the RSEL pin connected HI, the full-scale input range is set to 2Vp-p. In this configuration, the top and bottom references (REFT, REFB) provide an output voltage of +3.5V and +1.5V, respectively. Two resistors ( 2x 1.62kΩ) are used to create a common-mode voltage (VCM) of approximately +2.5V t ...
... With the RSEL pin connected HI, the full-scale input range is set to 2Vp-p. In this configuration, the top and bottom references (REFT, REFB) provide an output voltage of +3.5V and +1.5V, respectively. Two resistors ( 2x 1.62kΩ) are used to create a common-mode voltage (VCM) of approximately +2.5V t ...
HIGH INPUT VOLTAGE BUCK-BOOST CONVERTER WITH 2
... DETAILED DESCRIPTION DETAILED DESCRIPTION The controller circuit of the device is based on an average current mode topology. The controller also uses input and output voltage feedforward. Changes of input and output voltage are monitored and immediately can change the duty cycle in the modulator to ...
... DETAILED DESCRIPTION DETAILED DESCRIPTION The controller circuit of the device is based on an average current mode topology. The controller also uses input and output voltage feedforward. Changes of input and output voltage are monitored and immediately can change the duty cycle in the modulator to ...
2.5 V/3.0 V High Precision Reference AD780
... the high gain amplifier, which produces a precision 3 V output from an input voltage as low as 4.5 V (or 2.5 V from a 4.0 V input). The amplifier design also allows the part to work with +VIN = VOUT when current is forced into the output terminal. This allows the AD780 to work as a 2-terminal shunt ...
... the high gain amplifier, which produces a precision 3 V output from an input voltage as low as 4.5 V (or 2.5 V from a 4.0 V input). The amplifier design also allows the part to work with +VIN = VOUT when current is forced into the output terminal. This allows the AD780 to work as a 2-terminal shunt ...
