MAX3243 数据资料 dataSheet 下载
... absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 6 V Positive output supply voltage range, V+ (see Note 1) . . . . ...
... absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 6 V Positive output supply voltage range, V+ (see Note 1) . . . . ...
MAX4554/MAX4555/MAX4556 Force-Sense Switches General Description Features
... normally closed (NC) switches, two force switches, and two sense switches. The MAX4556 contains three independent single-pole/double-throw (SPDT) switches, of which one is a force switch and two are sense switches. These devices operate from a single supply of +9V to +40V or dual supplies of ±4.5V t ...
... normally closed (NC) switches, two force switches, and two sense switches. The MAX4556 contains three independent single-pole/double-throw (SPDT) switches, of which one is a force switch and two are sense switches. These devices operate from a single supply of +9V to +40V or dual supplies of ±4.5V t ...
LT5525 - High Linearity, Low Power Downconverting Mixer.
... Enable Voltage ............................... –0.3V to VCC + 0.3V LO Input Power ............................................... +10dBm LO+ to LO– Differential DC Voltage ......................... ±1V LO+ and LO– Common Mode DC Voltage... –0.5V to VCC RF Input Power ................................ ...
... Enable Voltage ............................... –0.3V to VCC + 0.3V LO Input Power ............................................... +10dBm LO+ to LO– Differential DC Voltage ......................... ±1V LO+ and LO– Common Mode DC Voltage... –0.5V to VCC RF Input Power ................................ ...
MAX8904 High-Efficiency Power-Management IC with I C
... of the ADJ power rail and boost regulator (voltage source mode), WLED current setting for the boost regulator (WLED current regulator mode), GPIO control, and enable/disable of ADJ, 5V0, boost regulator, CSA blocks. The I2C interface also enables the host processor to read on-board fault status regi ...
... of the ADJ power rail and boost regulator (voltage source mode), WLED current setting for the boost regulator (WLED current regulator mode), GPIO control, and enable/disable of ADJ, 5V0, boost regulator, CSA blocks. The I2C interface also enables the host processor to read on-board fault status regi ...
ZXTC6720MC Features and Benefits Mechanical Data
... 4. For a dual device surface mounted on 28mm x 28mm (8cm ) FR4 PCB with high coverage of single sided 2 oz copper, in still air conditions; the device is measured when operating in a steady-state condition. The heatsink is split in half with the exposed collector pads connected to each half. 5. Same ...
... 4. For a dual device surface mounted on 28mm x 28mm (8cm ) FR4 PCB with high coverage of single sided 2 oz copper, in still air conditions; the device is measured when operating in a steady-state condition. The heatsink is split in half with the exposed collector pads connected to each half. 5. Same ...
BDTIC www.BDTIC.com/infineon ® Version 2.0, 11 Jan 2012
... of peak power before entering protection, active burst mode for lowest standby power, propagation delay compensation for close power limit between high line and low line which also takes into consideration of slope compensation, frequency jittering for low EMI performance, the built-in auto-restart ...
... of peak power before entering protection, active burst mode for lowest standby power, propagation delay compensation for close power limit between high line and low line which also takes into consideration of slope compensation, frequency jittering for low EMI performance, the built-in auto-restart ...
Electromagnetism Qns - Tavistock College Science Department
... Source: adapted from V. PRUDEN and K. HIRST, AQA GCSE Sceince Reproduced by permission of Hodder and Soughton Educational Ltd ...
... Source: adapted from V. PRUDEN and K. HIRST, AQA GCSE Sceince Reproduced by permission of Hodder and Soughton Educational Ltd ...
differential integrator pixel architecture for dark current
... sensors is about 54dB which assesses the ability of a sensor to properly image both high lights and dark shadows in a scene. Also, the dark current prevents the sensor from taking images at low illumination levels. Several techniques have been proposed to reduce or compensate dark current. The diffe ...
... sensors is about 54dB which assesses the ability of a sensor to properly image both high lights and dark shadows in a scene. Also, the dark current prevents the sensor from taking images at low illumination levels. Several techniques have been proposed to reduce or compensate dark current. The diffe ...
AD7171 数据手册DataSheet下载
... Serial Clock Input. This serial clock input is for data transfers from the ADC. The SCLK has a Schmitt-triggered input. The serial clock can be continuous with all data transmitted in a constant train of pulses. Alternatively, it can be a noncontinuous clock with the information being transmitted fr ...
... Serial Clock Input. This serial clock input is for data transfers from the ADC. The SCLK has a Schmitt-triggered input. The serial clock can be continuous with all data transmitted in a constant train of pulses. Alternatively, it can be a noncontinuous clock with the information being transmitted fr ...
LTC1562-2 - Very Low Noise, Low Distortion Active RC Quad Universal Filter
... monolithic filters, no clock is needed. Four independent 2nd order filter blocks can be cascaded in any combination, such as one 8th order or two 4th order filters. Each block’s response is programmed with three external resistors for center frequency, Q and gain, using simple design formulas. Each ...
... monolithic filters, no clock is needed. Four independent 2nd order filter blocks can be cascaded in any combination, such as one 8th order or two 4th order filters. Each block’s response is programmed with three external resistors for center frequency, Q and gain, using simple design formulas. Each ...
Thevenin`s Theorem
... sources, current sources, and resistors. The sources can be any combination of dependent and independent sources. 2. We can find the values of the Thévenin equivalent by finding the opencircuit voltage and short-circuit current. The reference polarities of these quantities are important. 3. To find ...
... sources, current sources, and resistors. The sources can be any combination of dependent and independent sources. 2. We can find the values of the Thévenin equivalent by finding the opencircuit voltage and short-circuit current. The reference polarities of these quantities are important. 3. To find ...