20090826_FlatPanel_status
... ultra low distortion bandwidth at gain 2: 1.7GHz (output signal <0.5Vpp) bandwidth at gain 10: 370MHz operated in inverting mode fast slew rate: 3100V/ms low noise: 1.83nV/ Hz ...
... ultra low distortion bandwidth at gain 2: 1.7GHz (output signal <0.5Vpp) bandwidth at gain 10: 370MHz operated in inverting mode fast slew rate: 3100V/ms low noise: 1.83nV/ Hz ...
UC2852 数据资料 dataSheet 下载
... circuit to reactivate the switch cycle. Even though switching frequency varies with both load and instantaneous line voltage, it can be maintained within a reasonable range to minimize noise generation. While allowing higher peak switch currents than continuous PFCs such as the UC1854, this device o ...
... circuit to reactivate the switch cycle. Even though switching frequency varies with both load and instantaneous line voltage, it can be maintained within a reasonable range to minimize noise generation. While allowing higher peak switch currents than continuous PFCs such as the UC1854, this device o ...
Analog and Digital Multi
... While some impact is inevitable, it can be minimized through good meter design. Voltmeters are always connected in parallel with the component under test. A perfect voltmeter has infinite resistance, so that it draws no current from the circuit under test. However, perfect voltmeters only exist in t ...
... While some impact is inevitable, it can be minimized through good meter design. Voltmeters are always connected in parallel with the component under test. A perfect voltmeter has infinite resistance, so that it draws no current from the circuit under test. However, perfect voltmeters only exist in t ...
DN254 - LT1806: 325MHz Low Noise Rail-to-Rail SOT-23 Op Amp Saves Board Space
... bandwidth and noise performance achieved with several large-area photodiodes (and a small-area SFH213 for comparison). Note that large-area detectors also place extra demands on the gain bandwidth of an amplifier. The final case in Table 1 shows a 1MΩ transimpedance amplifier with 650kHz bandwidth f ...
... bandwidth and noise performance achieved with several large-area photodiodes (and a small-area SFH213 for comparison). Note that large-area detectors also place extra demands on the gain bandwidth of an amplifier. The final case in Table 1 shows a 1MΩ transimpedance amplifier with 650kHz bandwidth f ...
Rodgers_HPM_Effects - TerpConnect
... • The basic electronics of HPM effects • Summary of 2008 work – Began testing of mixed-signal systems – Studied HPM susceptibility of sensors (ARL) – Development of systems modeling capability ...
... • The basic electronics of HPM effects • Summary of 2008 work – Began testing of mixed-signal systems – Studied HPM susceptibility of sensors (ARL) – Development of systems modeling capability ...
EUP3510 Preliminary Current Limited Load Switch
... The EUP3510 is a Current Limited P-channel MOSFET power switch designed for high-side load-switching applications. An integrated current-limiting circuit protects the input supply against large currents which may cause the supply to fall out of regulation. It can be used to control loads that requir ...
... The EUP3510 is a Current Limited P-channel MOSFET power switch designed for high-side load-switching applications. An integrated current-limiting circuit protects the input supply against large currents which may cause the supply to fall out of regulation. It can be used to control loads that requir ...
News Musikmesse Frankfurt 2008
... signal that has to be processed by the external effect unit is connected to In 1. The signal can be attenuated by control Atten. before it is output to the 1/4" socket FX Send. The output of the external effect unit is connected to the 1/4" socket FX Return. The CF control of the A-138d works now as ...
... signal that has to be processed by the external effect unit is connected to In 1. The signal can be attenuated by control Atten. before it is output to the 1/4" socket FX Send. The output of the external effect unit is connected to the 1/4" socket FX Return. The CF control of the A-138d works now as ...
LM139, LM139A, LM239, LM239A, LM339, LM339A, LM2901
... SLCS006L − OCTOBER 1979 − REVISED JUNE 2004 ...
... SLCS006L − OCTOBER 1979 − REVISED JUNE 2004 ...
Bipolar Transistor 30V 300mA fT;3.5GHz typ. NPN Single PCP
... Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment (home appliances, AV equipment, communication device, office equipment, industrial equipment etc.). The products mentioned ...
... Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment (home appliances, AV equipment, communication device, office equipment, industrial equipment etc.). The products mentioned ...
Lecture-7 - WordPress.com
... The rectifier with a filter capacitor- Peak Rectifier • Assume, diode to be ideal. For an sine input, the capacitor charges to the peak of the input, Vp. • Then, diode operates in cut off mode and capacitor discharges through the load R. • The capacitor discharge will continue for almost the entire ...
... The rectifier with a filter capacitor- Peak Rectifier • Assume, diode to be ideal. For an sine input, the capacitor charges to the peak of the input, Vp. • Then, diode operates in cut off mode and capacitor discharges through the load R. • The capacitor discharge will continue for almost the entire ...
2 - Stephen F. Austin State University
... Control of the Power Factor Most household appliances are highly resistive and require high PF. Industry tends to be rather inductive. Some substations have capacitor banks timed to break in at certain times when inductive load changes, adjusting the PF to the desired value ...
... Control of the Power Factor Most household appliances are highly resistive and require high PF. Industry tends to be rather inductive. Some substations have capacitor banks timed to break in at certain times when inductive load changes, adjusting the PF to the desired value ...
RFVC1842 数据资料DataSheet下载
... Caution! ESD sensitive device. Exceeding any one or a combination of the Absolute Maximum Rating conditions may cause permanent damage to the device. Extended application of Absolute Maximum Rating conditions to the device may reduce device reliability. Specified typical performance or functional op ...
... Caution! ESD sensitive device. Exceeding any one or a combination of the Absolute Maximum Rating conditions may cause permanent damage to the device. Extended application of Absolute Maximum Rating conditions to the device may reduce device reliability. Specified typical performance or functional op ...
Opto-isolator
In electronics, an opto-isolator, also called an optocoupler, photocoupler, or optical isolator, is a component that transfers electrical signals between two isolated circuits by using light. Opto-isolators prevent high voltages from affecting the system receiving the signal. Commercially available opto-isolators withstand input-to-output voltages up to 10 kV and voltage transients with speeds up to 10 kV/μs.A common type of opto-isolator consists of an LED and a phototransistor in the same opaque package. Other types of source-sensor combinations include LED-photodiode, LED-LASCR, and lamp-photoresistor pairs. Usually opto-isolators transfer digital (on-off) signals, but some techniques allow them to be used with analog signals.